Posiflex LM-2412E User manual

Brand: Posiflex

Model: LM-2412E

Category: LED displays

Type: User manual

This manual is also suitable for

Package Contents

 12.1” TM/LM-2X12E LCD Monitor (x 1)

 VGA Cable (x 1)

 USB type A to B cable for TM-series

monitors (x 1)

 Mounting Kits (x 1)

 User Manual (x 1)

Product Features

 12.1” rear-mount monitor

 High compatibility with various Posiflex terminals

Monitor Model

Posiflex POS model

TM/LM-2212E

XP series models

TM/LM-2312E

KS 15”/17” series models

TM/LM-2412E

KS-7212E model

TM/LM-2512E

XT series models

TM/LM-2612E

HS series models

 Support of tilt adjustment: 42.5˚〜77.5 ˚

 Color choices: Black/Ivory

19630903010 Ver. Original

http://www.posiflex.com

TM/LM-2212E/2312E/2412E/2512E/2612E

LCD Monitor User Manual

Views of TM/LM-2212E

Front View

Rear View

Views of TM/LM-2312E/2412E

Front View

Rear View

Views of TM/LM-2512E

Front View

Rear View

Monitor Bracket

OSD Buttons

12.1” LM-2012E LCD Panel

12.1” TM-2012E Resistive Touch Panel

12.1” LM-2012E LCD Panel

12.1” TM-2012E Resistive Touch Panel

12.1” LM-2012E LCD Panel

12.1” TM-2012E Resistive Touch Panel

Power LED Indicator

Views of TM/LM-2612E

Front View

Rear View

View of I/O Interface of OSD Buttons

View of I/O Interface of LM-2X12E

View of I/O Interface of TM-2X12E

Monitor Bracket

OSD Button

EXT Button

＋ Button

－Button

Power Button

OSD Buttons

DC-IN Power Jack

USB (Type B) Port

USB (Type A) Port

VGA Port

DC-IN Power Jack

VGA Port

12.1” LM-2012E LCD Panel

12.1” TM-2012E Resistive Touch Panel

Power LED Indicator

Installing TM/LM-2X12E LCD Monitor

The installation of TM/LM-2212E/2312E/2412E/2512E/2612E are similar, but

slightly different due to the diverse content of mounting kits included in each

model. According to the model of your monitor, the relevant instructions are

provided below to help you mount TM/LM-2X12E onto your Posiflex

terminals. During installation, please ensure the terminal is properly turned off

and disconnected from the power sources to avoid potential hazards.

Mounting TM/LM-2212E onto XP series terminals

XP-3000 will be used to demonstrate installation of TM/LM-2212E in the

following example.

1. Position your terminal with its rear facing

towards you.

2. Lay the TM/LM-2212E on a flat surface with

the screen facing downward and its top side

facing toward you.

3. Steady the monitor with on hand, and then pull

the monitor bracket upright as shown in the

figure.

4. Lift the monitor. Align the three screw holes

on the monitor bracket with those on the rear

of the terminal.

5. Well secure the monitor bracket with the three

#6-32-10L fixing screws. Make sure TM/LM-

2212E is well mounted onto your terminal.

6. Connect the monitor to the terminal using VGA cable.

6.1 Align one end of the VGA cable with the

VGA port at the bottom I/O plate of your

monitor.

6.2 Take the other end of VGA cable to insert it into the VGA port in the

bottom I/O compartment of your terminal.

7. If the monitor you are using isn’t TM series, please skip this step.

For TM series users, connect the monitor to the terminal using USB

type A to B cable to enable touch function for your monitor.

7.1 Grab Type-B connector of USB cable, and

then insert it into Type-B USB port of your

monitor

7.2 Properly attach Type-A connector of USB cable to the POS terminal.

8. The installation of TM/LM-2212E is

completed.

Mounting TM/LM-2312E onto 15”/17” KS-series terminals

KS-7215 with Gen 8.5 base will be used to demonstrate installation of

TM/LM-2312E in the following example.

1. Position your terminal with its rear facing

towards you.

2. Take L type mounting bracket out of TM/LM-

2312E box package. Align the four screw holes

of the mounting bracket with the hole pattern

at the back of the terminal.

3. Insert four #6-32-12L fixing screws into the

screw holes and then tighten the screws to

secure the mounting bracket.

4. Lay the TM/LM-2312E on a flat surface with

the screen facing downward and its I/O ports

facing toward you. While holding the monitor

steady with one hand, pull the monitor bracket

upright.

5. Lift the monitor to align three screw holes on

the monitor bracket with those on the bracket

attached to the terminal using the alignment

dots.

6. Properly attach two brackets with three #6-32-

6L fixing screws. Make sure TM/LM-2312E is

well mounted onto your terminal.

7. Remove cable cover from the base of the

terminal.

8. Pull outward the locking levers and then

remove the neck cover in the direction shown

by the arrow.

9. Position the terminal with its screen facing toward you and then tilt the

screen up. Connect VGA and USB cables to I/O plate of your terminal.

9.1 Take the VGA cable out of the package to

insert one end of VGA cable to the VGA

port of your terminal.

9.2 For TM series users, attach Type-A connector of USB cable to

your POS terminal.

Alignment Dot

10. Pass the cables through the cable exit as shown

in the picture.

11. Flip the terminal with its rear toward you.

Neatly pull the cables out of the cable exit and

route it along the cable passage.

12. Push back the neck cover into place.

13. Push back the cable cover. Meanwhile, ensure the cable could be pulled

out of the cable exit from the base.

14. Install VGA and USB cables to the monitor.

14.1 Align the other end of the VGA cable with

the VGA port at the bottom I/O plate of

your monitor and secure it.

14.2 For TM series users, grab Type-B

connector of USB cable, and then insert it

into Type-B USB port of your monitor to

enable touch function.

15. The installation of TM/LM-2312E is

completed.

Cable exit

Cable Exit

Mounting TM/LM-2412E onto KS-7212E terminal

1. Position KS-7212E with its rear facing towards

you.

2. Take L type mounting bracket out of

TM/LM-2412E box package. Align the four

screw holes of the mounting bracket with the

hole pattern at the back of the terminal.

3. Insert four #6-32-12L fixing screws into the

screw holes and then tighten the screws to secure

the mounting bracket.

4. Lay the TM/LM-2412E on a flat surface with the

screen facing downward and its I/O ports facing

toward you. While holding the monitor steady

with one hand, pull the monitor bracket upright.

5. Lift the monitor to align three screw holes on the

monitor bracket with those on the bracket

attached to the terminal using the alignment dots.

6. Well attach two brackets with three #6-32-6L

fixing screws. Make sure TM/LM-2412E is well

mounted onto your terminal.

7. To release the neck cover from the base of the

terminal, pull outward four locking levers and

then remove it in the direction shown by the

arrow.

Alignment Dot

8. Connect VGA and USB cables to I/O plate of your terminal.

8.1 Take the VGA cable out of the package. Then, insert one end of

VGA cable to the VGA port of your terminal.

8.2 For TM series users, attach Type-A connector of USB cable to

your POS terminal.

9. Route the VGA cable through the cable exit of

the base.

10. Have you terminal positioned with its rear facing

towards you. Pull the cable out of the cable exit,

and then neatly route it along cable passage.

11. After ensuring the cable length is long enough

for you to connect to the monitor, push back the

neck over into place.

12. Make sure the cable can be pulled out of the

cable exit from the base.

13. Install VGA and USB cables to the monitor.

13.1 Align the other end of the VGA cable with the

VGA port at the bottom I/O plate of your

monitor and secure it.

13.2 For TM series users, grab Type-B connector

of USB cable, and then insert it into Type-B

USB port of your monitor to enable touch

function.

Cable exit

14. The installation of TM/LM-2412E is completed.

Mounting TM/LM-2512E onto XT series terminal

XT-3615 with Gen 7E base will be used to demonstrate installation of

TM/LM-2512E in the following example. The similar cable-routing skill can

also be applied to Gen 8E base.

1. Position your terminal with its rear facing

toward you. At the edges of the base stand

bracket are located two shorter horizontal rails

(2) (3) and two longer vertical rails (1) (4),

which are used to hold your cable into place.

2. Release the rail from the base.

To run the cable through the cable passage on the left, according to

the sequence number, first remove the longer rail and then the shorter

one from the base stand by sliding them in the direction shown by the

arrow.

Or, if you prefer to thread the cable through the cable passage on the

right side, first remove the longer rail and then shorter one from the

base stand according to the sequence number.

3. After positioning your terminal with its screen

facing downwards, lift the monitor and then

align the four fixing screw holes on its

mounting bracket with the hole pattern at the

rear of the terminal as shown in the figure.

4. Insert four #6-32-10L screws into the screws

holes and then tighten them to secure the

mounting bracket.

5. Install VGA and USB cables to the monitor.

5.1 Align the other end of the VGA cable with

the VGA port at the bottom I/O plate of your

monitor and secure it.

5.2 For TM series users, grab Type-B connector

of USB cable, and then insert it into Type-B

USB port of your monitor to enable touch

function.

6. Tuck the extra cables into cable passages. Please also reserve the

enough cable needed for tilting the monitor. In the example, it is

demonstrated how to route the cable through the cable passage on the

right side.

7. Push the rails back to the base.

If the cable is threaded through the cable passage on the right, by

following the sequence number, first slide the shorter rail horizontally

and then longer one vertically into place in the direction shown by the

arrow to fix your cable into place.

Alternatively, if you intend to lock the cable into the cable passage on

the left, according to to the sequence number, first slide the shorter rail

and then longer one into place in the direction shown by the arrow.

8. After the rails are sild back, make sure the

cable can be pull out of the bottom cable exit.

9. Remove the cover for the bottom I/O compartment.

10. Connect VGA and USB cables to I/O plate of your terminal.

10.1 Insert the other end of VGA cable to the VGA port of your

terminal.

10.2 For TM series users, attach Type-A connector of USB cable to

your POS terminal.

Cable Exit

11. After tucking the extra cable into the bottom

I/O compartment, push back the cover to close

the compartment.

12. After ensuring TM/LM-2512E is well

installed, tilt your monitor up or down to your

desired angle. While setting up the tilting

adjustment, be careful not to press on the LCD

panel.

Mounting TM/LM-2612E onto HS series terminal

HS-2310 will be used to demonstrate installation of TM/LM-2612E in the

following example.

1. Lay your POS terminal on a flat surface with

its rear facing towards you.

2. Press down the release tab of top I/O interface

cover.

3. Pull the top I/O cover in the direction shown

by the arrow in the figure to remove the

cover.

4. Position the monitor on a flat surface. While

keeping it steady with one hands, pull the rear

mounting bracket upright as shown in the

figure.

5. Lift the monitor up to align the four screw

holes of the mounting bracket with the holes

in the top I/O interface compartment of your

POS as shown in the figure.

6. Insert four #6-32-8L fixing screws into the

screw holes and tighten them to secure the

mounting bracket.

7. Connect the monitor to the terminal using VGA cable.

7.1 Insert one end of the VGA cable to the VGA

port at the bottom I/O plate of your monitor.

7.2 Take the other end of VGA cable to insert it into the VGA port in the

top I/O compartment of your terminal.

8. If the monitor you are using isn’t TM series, please skip this step.

For TM series users, connect the monitor to the terminal using USB

type A to B cable to enable touch function for your monitor..

8.1 Grab Type-B connector of USB cable, and

then insert it into Type-B USB port of your

monitor

8.2 Properly attach Type-A connector of USB cable to your POS

terminal.

9. Break the release tab of the top I/O interface

cover.

10. After tucking the extra cable into the I/O

compartment and thread the cable through the

cable exit, push the back cover into place.

Cable Exit

11. After ensuring TM/LM-2612E is well

installed, tilt your monitor up or down to your

desired angle. While setting up the tilting

adjustment, be careful not to press on the

LCD panel.

Identifying your Monitor as Secondary Touchscreen Monitor

in Extended Mode

Based on the type of your touch panels, you are required to adopt different

approaches to set up TM series as the extended monitor when you attempt to

extend the desktop across multiple monitors. In the following section the

related descriptions will be offered to help you achieve the purpose.

For TM-2X12E Model with Resistive Touchscreen

For TM-2X12E users, please follow the below instructions to complete

installation of The Dual Touch Manager, a tool designed to allow your monitor

to work as a secondary touchscreen monitor in extended mode.

1. Make sure that the monitor is well connected to your POS terminal with

USB type A to B cable.

2. Insert the Peripheral Information CD, which

is included in the package, into your CD-

ROM. Locate and double click the index

file.

3. Click on Peripheral Drivers & Utilities.

4. Click on TM/LM Series at the left side of

the menu.

5. Click on the Setup icon of USB Dual Touch Manager to install the

USB Dual Touch Manager.

6. Follow the instructions to complete the manager installation. After the

installation is finished, restart your terminal.

Activating Power Output to VGA port via BIOS Settings

In general, Posiflex terminals will disable the VGA power output in BIOS due

to safety concerns. In the case of using your Posiflex terminal to supply power

to monitors, it is required to manually enable the VGA power of the terminals

in BIOS settings so that the monitor is able to extract power from the Posiflex

terminals. However, if the monitor you are using is not manufactured by

Posiflex, it is strongly suggested to deactivate the VGA power of your terminal

in preventing your device from being damaged.

The following will describe the steps required to enable VGA port in BIOS

setting. For those users who intend to power the monitors using power

adaptor included in your package, you may skip this section. Besides,

please DO NOT plug the VGA cable into VGA connectors while the terminal

is still running.

1. Make sure that TM/LM-2X12E is well connected to the Posiflex terminals

using the VGA cable.

2. Press the power button of the POS to power on the POS. During the boot

process, hit F2 key to access BIOS setting.

3. Navigate through BIOS using arrow and Enter keys to access the setting

of VGA port. If it is set to be disabled, hit Enter key to enable the VGA

power output.

4. Switch to Exit tab and select Exit Saving Changes option. Choose Yes in

Setup Confirmation message box to save your configurations.

5. After rebooting your POS, make sure the monitor is correctly detected.

Status LED Indicator

LED status indicators, which are located at the bottom of the screen, are

designed to notify users of the current status of your monitor by emitting

various LED signals. Please refer to the below chart to accurately interpret the

status indicators to facilitate your troubleshooting.

LED

Status

Description

POWER LED

ON, solid green

System Standby

ON, solid blue

System power ON

OFF

System power OFF

Powering ON/OFF TM/LM-2X12E

Instead of using an external power supply, TM/LM-2X12E mainly depends on

Posiflex POS terminals as primary power sources. In such a case, the LCD

monitor will be automatically initiated when the terminal is powered up and

shut down immediately after you power the POS down. If the monitor does not

work as expected, please make sure that you properly change BIOS settings as

specified in Activating Power Output to TM/LM-2X12E via POS System

BIOS section.

Power ON TM/LM-2212E/2312E/2412E/2512E/2612E

Press the power button of the POS terminal to power on your terminal. Few

seconds later the monitor will be initiated.

Power OFF TM/LM-2212E/2312E/2412E/2512E/2612E

After following the standard shutdown procedure to power off the POS

terminal, the monitor will be turned off accordingly.

Setting up the Best Display Resolution for your Monitor

The below chart defines the list of recommended display settings which you

are able to use for TM/LM-2X12E. Improper display configuration will

prevent the monitor from displaying the image and lead to a warning message

of “out of range” prompted on the screen.

Display Resolution

Refresh Rate (Hz)

Horizontal Frequency (KHz)

640*400

37.9

640*480

31.5

37.9

37.5

720*400

37.9

800*600

35.1

37.9

48.1

46.9

1024*768

48.4

56.5

Introducing the Posiflex OSD Menu

OSD, as known as On Screen Display, is employed to assist users in adjusting

a variety of monitor-related settings depending on personal preference.

Through this section, it is expected to familiarize you with the options which

are accessible via OSD menu and to optimize your experiences with

TM/LM-2X12E

Power & OSD Buttons

Below are guidelines on how to navigate through OSD menu:

1. To get started with OSD, press OSD button to access OSD menu.

2. Scroll through OSD menu options using EXT button.

3. Push OSD button to choose the particular menu option of interest and to

enter its sub-menu.

4. If the selected menu option contains sub-menu items, push EXT button

to browse available items.

5. Use “＋” or “－” buttons to adjust the value of the selected OSD item.

Power & OSD buttons are located on the rear, right-hand

side of TM/LM-2X12E. Each of five OSD controls works

differently in various occasions. Please refer to the below

figure to get an idea of how they could possibly function in

relation to OSD menu.

Icon

Description

OSD button

 to activate OSD menu

 to select the specific menu option

EXT button

 to exit from the current configuration

 to navigate through OSD menu options

“＋” Button

 to increase the value of the specific item

“－” Button

 to decrease the value of the specific item

 auto-tune feature

Power Button

 to turn the monitor ON/OFF

OSD Options

Posiflex OSD menu contains a set of six OSD options, and each option could

be comprised of several sub-options to offer more specific configurations.

OSD Menu Options

Sub-menu items & Description

Picture

 Backlight

Press the “＋” button to increase backlight

intensity;

Press the “－” button to decrease backlight

intensity.

 Brightness

Press the “＋” button to increase brightness;

Press the “－” button to decrease brightness.

 Contrast

Press the “＋” button to increase contrast;

Press the “－” button to decrease contrast.

 Sharpness

Press the “＋” button to increase sharpness;

Press the “－” button to decrease sharpness.

Display

 Auto Adjustment

Execute the auto-tune function for OSD menu,

which will automatically perform fine tune of

the image quality for optimizing screen

performance.

 H Position

Press the “＋” button to move the screen to the

right;

Press the “－” button to move the screen to the

left.

 V Position

Press the “＋” button to move the screen up;

Press the “－” button to move the screen down.

 Pixel Clock

Use the “＋” or “－” button to adjust the

Clock setting for VGA input.

 Phase

Use the “＋” or “－” button to adjust the

Phase setting for VGA input.

OSD Menu Options

Sub-menu items & Description

Other

 Reset

Restore the current menu back to the default

setting.

 Menu Time

Specify the length of time for OSD menu to

stay active on the screen.

 Language

Specify the language used in the OSD menu.

Information

Display information regarding display resolution,

horizontal/vertical sync frequency, pixel clock

(PCLK), etc.

Specifications

TM-2X12E

LM-2X12E

Display

LCD Panel

12.1" TFT LCD

Resolution

1024 (H) x 768 (V)

Active Area (mm)

245.76 (H) x 184.32 (V)

Pixel Pitch (mm)

0.24(H) x 0.24 (V)

Pixel Arrangement

R.G.B. Rectangle

Viewing Angle

70/70/70/70 degree (U/D/L/R)

Contrast Ratio

800 : 1

Response Time

16 ms

Brightness

350 cd/m

General Specification

Display Interface

VGA

Power Supply

12V from Posiflex terminal VGA port

Touch

Touch type

5-wire Resistive

N/A

Interface

USB

N/A

※ The product information and specifications are subject to change without

prior notice. To get the detailed information on TM/LM-

2212E/2312E/2412E/2512E/2612E, please check this model from Posiflex

Global Website (http://www.posiflex.com/en-global/Download/download).

Posiflex LM-2412E User manual

Brand: Posiflex

Model: LM-2412E

Category: LED displays

Type: User manual

This manual is also suitable for

Download PDF

report

Posiflex LM-2412E User manual

This manual is also suitable for

Posiflex LM-2412E User manual

Related papers

Other documents