Baby Lock Coronet Longarm Assembly Instructions

Brand
Baby Lock
Model
Coronet Longarm
Category
Car kits
Type
Assembly Instructions
5-Foot Pole Upgrade Kit Assembly Instrucons | 1
5-Foot Pole Upgrade Kit
Assembly Instrucons
Table of Contents
2 Frame Parts and Hardware
6 Geng Started: New Frame or Updang an Exisng Frame
7 Top and Boom Bracket Assembly
8 Pole Bearing Assembly
9 Ratchet Stop Boom Assembly
10 Ratchet Stop Top Assembly
11 Pole Assembly
15 Velcro®
16 Leader Assembly
Introducon
This 5-Foot Pole Upgrade Kit includes special brackets and poles which allow the quilt to be rolled and
advanced to simplify quilng small quilts on your space-saving frame.
Back of
Frame
Front of
Frame
2 | 5-Foot Pole Upgrade Kit Assembly Instrucons
What’s Included:
Parts and Hardware
Box 1
1 - Top Bracket Le
1 - Top Bracket Right
2 - Pole Bearing Assembly Unplugged
1 - Bracket Boom Le QB
1 - Bracket Boom Right QB
2 - Pole Bearing Assembly Plugged
1 - Ratchet Wheel Assembly Long
1 - Ratchet Wheel Assembly Short
2 - Pole End Assembly
1 - Hand-wheel Assembly
1 - Set of 2 Pole Keeper Cap
4 - Screw Thread End Cap
2 - Ratchet Stop Bushing
2 - Ratchet Stop Holder
4 - Ratchet Stop Mount
2 - Ratchet Stop
2 - Screw M6 X 48 SWH
4 - Screw M6 X 25
8 - Screw M6 X 20
4 - Screw M6 X 10
12 - Nut M6, Lock nut
2 - 4 1/2 Foot Leaders
2 - 5' 8" Velcro®
1 - Pole End Wrench (10mm)
1 - Hex Key L4mm
1 - Hex Key L5mm
Box 2
2 – Pole Rear
5-Foot Pole Upgrade Kit Assembly Instrucons | 3
Top Bracket Le
(1) QF00011-04
Pole Rear
(2) QF10009
Hand Wheel Plug Insert
Info only, to order insert use:
(0) QF09318-713
Hand-wheel Assy w/insert
(1) QF09318-09325
Pole End Assy
(2) QF09326
Ratchet Wheel Assy Short
(1) QF09320
Ratchet Wheel Assy Long
(1) QF09321
Pole Bearing Assy Unplugged
(2) QF00011-50
Bracket Boom Right QB
(1) QF00011-01
Bracket Boom Le QB
(1) QF00011-02
Pole Bearing Assy Plugged
(2) QF0001-40
Top Bracket Right
(1) QF00011-03
4 | 5-Foot Pole Upgrade Kit Assembly Instrucons
Screw Thread End Cap
(4) QF09318-716
Screw M6 X 48 SWH
(2) QF09318-204
Ratchet Stop
(2) QF09318-203
Ratchet Stop Mount
(4) QF09318-202
Ratchet Stop Holder
(2) QF09318-205
Ratchet Stop Bushing
(2) QF09318-201
Screw M6 X 20
(8) QM10443
5' 8" Velcro® Hook Tape
(2) QF00662
4 ½ Foot Leaders
(2) QF09561
Screw M6 X 10
(4) QM13300
Nut M6, Locknut
(12) HG01100-100
Screw M6 X 25
(4) QM10447
5-Foot Pole Upgrade Kit Assembly Instrucons | 5
Wrench Pole Assy (10mm)
(1) QF09318-12
L Hex Key 5mm
(1) QM10289
L Hex Key 4mm
(1) QM10288
Set of 2 Pole Keeper Cap
(1) QF05300-01
6 | 5-Foot Pole Upgrade Kit Assembly Instrucons
Geng Started
New Frame
1. Follow the frame assembly instrucons unl
it discusses the front L-brackets for 16" and
18" machines.
2. Begin 5-Foot Pole Upgrade Kit assembly
steps on page 7.
3. Aer compleng the 5-Foot Pole Upgrade
Kit assembly instrucons, complete the
frame instrucons.
Exisng Frame
1. The screws in the frame front L-brackets
will need to be removed and replaced with
the longer screws and nuts to hold the front
bracket assembly shown on the next page
(page 7).
 IMPORTANT: It is recommended that
you have a second person to help
hold the front bracket and L-bracket
while you replace the screws through
the front bracket assembly into the
L-Bracket.
5-Foot Pole Upgrade Kit Assembly Instrucons | 7
The vercal piece at the top rear of the
exisng frame side arm bracket is for the
5-Foot Pole Upgrade top bracket. It is
pre-threaded for the M4 x 10 screws found
in the 5-Foot Pole Upgrade hardware.
Parts Needed
1 - Bracket Top Le
1 - Bracket Top Right
1 - Bracket Boom Le
1 - Bracket Boom Right
4 - Screw, M6 X 10
4 - Screw, M6 X 25
4 - Nut, M6 Locknut
Tools Needed
4mm L Hex Key (provided)
5mm L Hex Key (provided)
10mm Wrench (provided)
1. Locate the top right bracket.
2. Align it with the side arm as shown in the
image at the right (A).
3. Start the screws into the pre-threaded
holes and ghten the screws rmly with
the provided 4mm L hex tool.
4. Locate the boom right bracket.
5. Align the bracket as shown in the image
at the right (B).
6. Insert the screws through the boom
bracket and the side arm bracket.
7. Place a locknut onto both screws. The
screw heads will be on the outside and
the locknuts will be towards the inside
of the frame (C).
8. Tighten the nuts fully using the provided
5mm L hex key and the 10mm wrench.
9. Repeat steps 1-8 for the le side of the
frame.
Top and Boom Bracket Assembly
(A)
(B)
(C)
8 | 5-Foot Pole Upgrade Kit Assembly Instrucons
Pole Bearing Assembly
These instrucons show the hand-wheel
and ratchet stops on the right side. They can
be installed on either side, based on your
preference.
Parts Needed
2 - ENG-QF00011-100
2 - ENG-QF00011-200
8 - Screw, M6 X 20
8 - Nut, M6 Locknut
Tools Needed
5mm L Hex Key
10mm Wrench
1. Locate the unplugged pole bearing
assemblies (QF00011-50).
2. Place the unplugged pole bearing
assembly down over the right top
bracket. The pole bearing assembly will
straddle it. See image A.
3. Insert the two screws toward the center
of the frame.
4. Place a locknut on each screw and fully
ghten them with the 5mm L hex key,
and the 10mm wrench (provided).
5. Repeat the process with the boom right
bracket. Use the second pole bearing
assembly (QF00011-50). See image B).
6. Repeat the process for the top le
bracket and boom le bracket on the
other end of the frame, using the plugged
pole bearing assemblies (QF00011-40).
A
B
5-Foot Pole Upgrade Kit Assembly Instrucons | 9
Shown at right is the boom right bracket
with exploded ratchet stop assembly,
located at the front of the frame. Follow the
steps in order of the sequence shown in the
diagram.
Parts Needed
1 - Ratchet Stop Holder
1 - Ratchet Stop Mount
1 - Ratchet Stop Bushing
1 - Ratchet Stop
1 - Screw, M6 X48 SWH
Tools Needed
4mm L Hex Key
1. Place the ratchet stop holder (1) in
between the two outside brackets with
the tab located as shown.
2. Insert the square side of the ratchet stop
mount (2) into the outside bracket. The
screw will ghten into this mount later.
3. Place the square part of the ratchet stop
bushing into the inside bracket.
4. Align the ratchet stop as shown in the
image and slide it over the bushing (4).
5. Insert the M6 x 48 special large washer
head screw through the bushing and
assembly, then ghten fully with the
4mm hex tool provided.
6. The image at right shows the assembled
boom ratchet stop found at the front of
the frame.
1
2
3
4
5
Tab
Boom Ratchet Stop Assembly
10 | 5-Foot Pole Upgrade Kit Assembly Instrucons
Shown to the right is the top right bracket
with exploded ratchet stop assembly, which
is located at the rear of the frame. Follow
stesp in order of the sequence shown in the
diagram.
Parts Needed
1 - Ratchet Stop Holder
1 - Ratchet Stop Mount
1 - Ratchet Stop Bushing
1 - Ratchet Stop
1 - Screw, M6 X48 SWH
Tools Needed
4mm L Hex Key
1. Place the ratchet stop holder in between
the two outside brackets with the tab
located as shown.
2. Place the ratchet stop mount into the
outside bracket with the square side into
the bracket and the round side out. The
screw will ghten into this mount later.
3. Place the square part of the ratchet stop
bushing into the inside bracket.
4. Align the ratchet stop as shown in the
image and slide it over the bushing.
5. Insert the M6 x 48 special large washer
head screw through the bushing and
assembly and ghten fully with the
4mm hex tool provided.
6. The boom image shows the assembled
top ratchet stop at the rear of the frame.
1
2
3
4
5
Tab
Top Ratchet Stop Assembly
5-Foot Pole Upgrade Kit Assembly Instrucons | 11
Pole End Assembly
Two poles will be assembled, one top pole
assembly with ratchet and hand-wheel and
one boom pole assembly with ratchet.
Both poles have a pole end assembly on
one end.
Parts Needed
2 - Pole Rear
1 - Ratchet Wheel Assembly Long
1 - Ratchet Wheel Assembly Short
1 - Hand-Wheel Assembly
2 - Pole End Assembly
Tools Needed
1 - Pole Assembly Wrench
1 - 17mm wrench (provided with Frame)
Top Pole with Hand-Wheel and
Ratchet Wheel:
1. Loosen the nut on the ratchet wheel long
bolt assembly, but do not remove it. Push
the bolt towards the back of the ratchet
wheel to loosen the wedge. This will
allow the assembly to be inserted freely
into the pole end.
2. Place the assembly into the pole end unl
the metal pole touches inside the small
lip on the ratchet wheel assembly.
3. Remove the nut and small outside
washer.
4. Place the hand-wheel with hand wheel
plug bushing, the small washer, and the
locknut onto the long bolt.
5. Align the three protruding tabs on the
hand-wheel plug bushing with the three
hand-wheel notches on the inside pole
wedge.
NOTE: The ratchet wheel has three
holes for the tabs on the outside
pole end and the hand-wheel plug
bushing has three tabs that go into
three notches on the outside pole
end to keep them from slipping.
Notch
Tab
Tab in hole
12 | 5-Foot Pole Upgrade Kit Assembly Instrucons
Pole End Assembly connued
6. While holding the pole end ratchet rmly,
ghten the locknut with a 17mm wrench
(provided with frame).
NOTE: The nut will appear to be all the
way ght when it is only about half
way ghtened. Connue ghtening
unl it will ghten no further. There
should be a minimum of 3/8" to
1/2" of exposed threads beyond the
locknut.
 IMPORTANT: If the nut is not fully
ghtened the hand-wheel will slip and
damage the hand-wheel plug insert.
7. Cover the exposed threads by sliding a
rubber screw thread end cap over them.
Boom Pole with Ratchet Wheel:
8. Loosen the nut on the ratchet wheel short
bolt assembly, but do not remove it. Push
the bolt towards the back of the ratchet
wheel to loosen the wedge. This will allow
the assembly to be inserted freely into the
pole end.
9. Place the assembly into the pole end unl
the metal pole touches inside the small lip
on the ratchet wheel assembly.
10. Align the three tabs on the outside pole
end with the three holes on the ratchet
wheel.
11. Tighten the locknut fully unl it has 3/8"
to 1/2" threads exposed and it will not
ghten any more.
12. Cover the exposed threads by sliding a
rubber screw thread end cap over them.
Pole End Assembly:
13. Repeat the loosening, inserng an
ghtening processes for the two simple
pole end assemblies (one on each pole)
and cover the threads with a screw
thread end cap.
5-Foot Pole Upgrade Kit Assembly Instrucons | 13
Pole End Assembly connued
Pole end
Handwheel with ratchet pole
(top rear)
Ratchet pole
(boom front)
14 | 5-Foot Pole Upgrade Kit Assembly Instrucons
Pole End Assembly connued
Pole Keepers
A set of pole keepers are provided for the
boom front pole.
14. Place the pole keeper with the wide part
over the wide opening as shown in the
detailed image.
15. Aer you have assembled the poles, place
them on the frame as shown in the image
below.
5-Foot Pole Upgrade Kit Assembly Instrucons | 15
Velcro® Assembly
The two poles with ratchet wheels will
need to have one piece of hook Velcro tape
installed straight across them from end to
end. Two pieces of hook Velcro 5' 8" long
are provided. It is important that this be
installed straight on the pole to make it
possible for you to load the quilt straight.
1. Check how the Velcro ts across the pole.
Make small marks to help you to start
the Velcro at the right place and keep it
straight.
2. Peel the backing from the Velcro a small
amount at a me as you place it across
the pole, keeping the Velcro straight.
16 | 5-Foot Pole Upgrade Kit Assembly Instrucons
Leader Assembly
Apply the Velcro edge of the leaders to the
hook Velcro adhered to the poles.
The quilt backing is then pinned to the
leaders.
Refer to the images at the right to aid in
wrapping the leaders and quilt backing
around the poles in the correct manner.
With the ratchets engaged, the poles will
only turn in the correct direcon.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Baby Lock Coronet Longarm Assembly Instructions

Brand
Baby Lock
Model
Coronet Longarm
Category
Car kits
Type
Assembly Instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents