Suzuki 990D0-48G00-ALM Fitting Instructions Manual

Brand: Suzuki

Model: 990D0-48G00-ALM

Type: Fitting Instructions Manual

Suzuki 990D0-48G00-ALM: The state-of-the-art Suzuki 990D0-48G00-ALM electronic alarm system, designed specifically for VZR 1800 motorcycles, seamlessly integrates with your vehicle's original wiring for quick and secure installation. Enhance your motorcycle's security with this advanced alarm system, engineered to safeguard your prized possession and provide peace of mind.

Installation kit for Alarm

Kit installazione per Allarme

Kit de montage l’Alarme

Kit instalacìon para Alarma

Installationssatz für Alarmanlage

Part Number:

990D0-48G00-ALM

Date:

08/01/2007

Importer’s Stamp

Page is loading ...

Fitting Instructions

Description: Electronic Alarm System Part. Number: 990D0-48G00-ALM

Applies to: VZR 1800 Fitting time: 1 hour

CONTENTS

Reference Descritpion Quantity

Pin to Pin harness

LED with case

Cable tie (4 L=260mm)

Doubled-sided adhesive tape

Fitting instructions

Paper mask

Reference Descritpion

Screw driver PH

Ring spanner 8mm and 10mm

Allen Key 4mm

Side Cutter

Read this leaflet with care and carry out the instructions provided.

You will come across a few special symbols and terms with a specific meaning in these instructions; they

are used to emphasise certain fundamental aspects during fitting.

WARNING

This indicates a potential hazard which could result in death or injury

CAUTION

This indicates a potential hazard which could result in damage to the vehicle

NOTE

This indicates special information, required for maintenance and to safeguard correct fitting

TOOLS

IMPORTANT

State of the art. 01/2007

SUZUKI GENUINE ACCESSORIES

PRIOR TO FITTING

1. Check that all the parts shown are included in the Kit.

2. Check the condition of each individual part.

3. Park the vehicle in a stable manner.

4. Take the key out of the ignition, allow the engine/exhaust to cool prior to installation.

5. Protect all parts removed from the vehicle.

6. Be careful not to damage any vehicle parts during fitting.

State of the art. 01/2007

SUZUKI GENUINE ACCESSORIES

CAUTION

The condition to assemble parts is technical experience.

If you not sure if you do a special work step, you should ask your next SUZUKI dealer.

NOTE:

The vehicle’s original wiring is designed to connect directly up to the alarm system.

The two connectors (single-pole connector and four-pole connector closed with matching part)

are located on the left side midway along the vehicle, underneath the battery support.

STEP-BY-STEP FITTING GUIDE

Fitting Instructions

Photo 1: Connect the connector on the alarm’s harness up to the control unit, insert the rubber hood into

its housing (1) and secure it using a cable grip (2).

Illustration of the connectors: (3) LED, (4) Direction indicators, (5) Alarm Connection.

Clean the bottom of the control unit and stick down the double-sided adhesive tape provided in the kit (6).

Photo 2: Remove the main saddle (A).

Photo 3: Remove the two side fairings (B). Take off the battery shield by removing the two side clips (C).

Disconnect the main power supply cables, remove the solenoid starter and release the fuse box (D).

Photo 4: Remove the battery and the tool bag. Take off the plastic battery support by unscrewing the three

relative screws (E) and removing the fuse box (F).

Photo 5: Take hold of the plastic battery support (G) and turn it by 180 degrees (H); put the paper template

into position (I) previously cut as shown in the photograph (L) and drill two holes with a diameter of 4 mm.

Use double-sided adhesive tape to attach the alarm unit as shown in the photograph (M), securing it using

two plastic grips.

CAUTION:

The alarm loom must face to the right, as shown in the photograph (M).

CAUTION:

To avoid potential damage of the remote control while driving,

do not carry along

the remote control connected to the ignition key.

Photo 6: Replace the plastic battery support, complete with the alarm, replace the electric parts you

removed earlier, starter solenoid and fuse box, put the battery back on and reconnect the wiring (N).

Connect the two connectors on the vehicle for the alarm, after removing the link plug, with the matching

connectors on the alarm loom (O), lay out the section of alarm loom with the two 6-way connectors towards

the rear of the vehicle until it reaches the motor cycle’s 6-way connector; disconnect this and fit the alarm

connectors (P). Leave the section of alarm loom with the black, two-way connector for the LED close to the

tank.

Photo 7: Attach the LED to the left fairing (R), as shown in photograph 7.

When you are replacing the side fairings, connect up the two-way connector for the LED with the matching

connector located close to the tank.

Replace the plastic parts you removed earlier from both sides of the motorcycle.

State of the art. 01/2007

SUZUKI GENUINE ACCESSORIES

Enabling the alarm system

The alarm must be initiated to make it operational. To do this, turn the ignition key OFF-ON-OFF.

The alarm system’s LED (Photograph 7) will now flash, indicating how many remote controls have been paired

up to the system by flashing the appropriate number of times (two are supplied as standard).

The system is now operational. Please refer to the user manual, supplied with the Alarm Kit item code

990D0 – ALARM – 000 for further details and specifications.

HOW TO ENABLE THE ALARM SYSTEM

Fitting Instructions

Page is loading ...

State of the art. 01/2007

SUZUKI GENUINE ACCESSORIES

State of the art. 01/2007

SUZUKI GENUINE ACCESSORIES

Designed and manufactured by Meta System S.pA. V81545A [email protected]

Suzuki 990D0-48G00-ALM Fitting Instructions Manual

Brand: Suzuki

Model: 990D0-48G00-ALM

Type: Fitting Instructions Manual

Download PDF

report

Suzuki 990D0-48G00-ALM Fitting Instructions Manual

Suzuki 990D0-48G00-ALM Fitting Instructions Manual

in other languages

Related papers

Other documents