Suzuki 990D0-17H00-ALM Installation guide

Type
Installation guide

Suzuki 990D0-17H00-ALM is an electronic alarm system designed for the protection of your motorcycle. It features a compact and waterproof central unit, a high-intensity LED indicator, and a two-way remote control with a range of up to 1000 meters. The alarm system is equipped with multiple sensors that detect motion, vibration, and unauthorized entry attempts, providing comprehensive protection for your vehicle. The system also includes a panic mode, which can be activated by pressing the panic button on the remote control, triggering the alarm and attracting attention in case of an emergency.

Suzuki 990D0-17H00-ALM is an electronic alarm system designed for the protection of your motorcycle. It features a compact and waterproof central unit, a high-intensity LED indicator, and a two-way remote control with a range of up to 1000 meters. The alarm system is equipped with multiple sensors that detect motion, vibration, and unauthorized entry attempts, providing comprehensive protection for your vehicle. The system also includes a panic mode, which can be activated by pressing the panic button on the remote control, triggering the alarm and attracting attention in case of an emergency.

EN
Fitting Instructions
Description: Electronic Alarm System Part. Number: 990D0-17H00-ALM
Applies to:
GSF650 K5-K8, GSF1200 K6, GSF1250 K7-K8, GSX650F K8 Fitting time: 1 hour
CONTENTS
Reference Descritpion Quantity
A
B
C
D
E
Pin to Pin harness
LED with case
Cable tie (L=260mm)
Fitting instructions
Silicon glue
1
1
3
1
1
Reference Descritpion
1
2
3
4
Screw driver PH
Ring spanner 10mm
Allen Key 4mm, 5mm and 6mm
Side Cutter
Read this leaflet with care and carry out the instructions provided.
You will come across a few special symbols and terms with a specific meaning in these instructions; they
are used to emphasise certain fundamental aspects during fitting.
WARNING
This indicates a potential hazard which could result in death or injury
CAUTION
This indicates a potential hazard which could result in damage to the vehicle
NOTE
This indicates special information, required for maintenance and to safeguard correct fitting
TOOLS
IMPORTANT
3
State of the art. 01/2008
SUZUKI GENUINE ACCESSORIES
PRIOR TO FITTING
1. Check that all the parts shown are included in the Kit.
2. Check the condition of each individual part.
3. Park the vehicle in a stable manner.
4. Take the key out of the ignition, allow the engine/exhaust to cool prior to installation.
5. Protect all parts removed from the vehicle.
6. Be careful not to damage any vehicle parts during fitting.
4
State of the art. 01/2008
SUZUKI GENUINE ACCESSORIES
CAUTION
The condition to assemble parts is technical experience.
If you not sure if you do a special work step, you should ask your next SUZUKI dealer.
NOTE:
The vehicle’s original wiring is designed to connect directly up to the alarm system.
The two connectors (single-pole connector and four-pole connector closed with matching part)
are located on the left side midway along the vehicle, underneath the battery support.
STEP-BY-STEP FITTING GUIDE
EN
Fitting Instructions
Photo 1: Connect the connector on the alarm’s harness up to the control unit, insert the rubber hood into its
housing (1) and secure it using a cable grip (2).
Illustration of the connectors: (3) LED, (4) Direction indicators, (5) Alarm Connection.
Photo 2: Remove the main saddle (A) and the two side fairings (B), pull out the two plastics clips, located on
both sides of rear fairing (C).
Photo 3: Unscrew the fours screws (D) and remove the passengers handle (E), remove the metallic wire of the
mechanical unblock seat and tools bag (F). Before removing the rear fairing, disconnect the connector of the
rear tail lamp.
Photo 4: Turn the rear fairing upside down and clean the space for the alarm unit(G), and the unit it self with a
suitable cleaner.
Photo 5: Put the silicon glue on the bottom of the alarm unit, and stick the unit on the specific space (H).
The alarm unit must be near to the rear tail lamp, about 5 mm.
CAUTION:
The silicon glue need about 24 hours to have a completely catalyze
Enabling the alarm system
The alarm must be initiated to make it operational. To do this, turn the ignition key OFF-ON-OFF.
The alarm system’s LED (Photograph 8) will now flash, indicating how many remote controls have been paired
up to the system by flashing the appropriate number of times (two are supplied as standard).
The system is now operational. Please refer to the user manual, supplied with the Alarm Kit item code
990D0 – ALARM – 000 for further details and specifications.
HOW TO ENABLE THE ALARM SYSTEM
Photo 6: The two connector dedicated for the alarm system are located on the back up of the plate (I), there
are also available the two connectors for the indicator lights (L).
Photo 7: After 24 hours replace the rear fairing
Connect the alarms connector, the indicator light connectors and the rear tail lamp connector (M), fix the alarm
wiring loom with cable tie (N), and run the Led cable on the front of vehicle (O).
Lock the wire for the mechanical unblock seat (P),
Photo 8: Attach the Led (Q) to the left side as shown in photograph 8.
Photo 9: Connect the two-way connector of the LED with the alarm wiring loom (R).
Replace the plastic parts you removed earlier from both sides of the motorcycle.
13
State of the art. 01/2008
SUZUKI GENUINE ACCESSORIES
1
3
4
2
14
State of the art. 01/2008
SUZUKI GENUINE ACCESSORIES
5
6
7 8
15
State of the art. 01/2008
SUZUKI GENUINE ACCESSORIES
9
Designed and manufactured by Meta System S.pA. V81546B [email protected]
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Suzuki 990D0-17H00-ALM Installation guide

Type
Installation guide

Suzuki 990D0-17H00-ALM is an electronic alarm system designed for the protection of your motorcycle. It features a compact and waterproof central unit, a high-intensity LED indicator, and a two-way remote control with a range of up to 1000 meters. The alarm system is equipped with multiple sensors that detect motion, vibration, and unauthorized entry attempts, providing comprehensive protection for your vehicle. The system also includes a panic mode, which can be activated by pressing the panic button on the remote control, triggering the alarm and attracting attention in case of an emergency.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI