Legrand DSL Modem Mounting Plate - 364808-11 / 364808-12 Installation guide

Legrand
Brand
Legrand
Model
DSL Modem Mounting Plate - 364808-11 / 364808-12
Type
Installation guide

This manual is also suitable for

INSTRUCTION/INSTALLATION SHEET
DSL MODEM MOUNTING PLATE IS-0308 REV. O
Page 1 of 2
301 Fulling Mill Road, Suite G ©Copyright 2005 by OnQ Technologies, Inc All Rights Reserved.
Middletown, PA 17057 www.onqhome.com
(800)-321-2343
Innovations in Home Living.
1. Introduction
The On-Q Home DSL Modem Mounting Plate is designed to easily mount a DSL modem inside an On-Q Home enclosure,
and is available as two different versions (P/N 364808-11 and 364808-12) as shown and described below. The Data Surge
Conditioning Unit, shown as part of the P/N 364808-12 version, may also be ordered as a standalone product (P/N 364598-
01).
2. Description
The On-Q Home DSL Modem Mounting Plate, (see Figure 1-2) is designed to be mounted in an On-Q Home enclosure,
with two tabs on one end and a locking tab on the other. The two versions contain the following components:
P/N 364808-11 version P/N 364808-12 version
1 DSL Splitter Conditioning Unit 1 DSL Splitter Conditioning Unit
2 DSL modem mounting straps 1 Data Surge Conditioning Unit
1 DSL Splitter to DSL modem jumper 2 DSL modem mounting straps
1 ground wire and screw 1 DSL Splitter to DSL modem jumper
1 DSL modem to Data Surge CAT5e jumper
1 ground wire and screw
DSL Modem Mounting Plate P/N 364808-11
Mounting
Straps
DSL Splitter
Conditioning
Unit
Figure 1
Phone +
DSL in
DSL
Modem
(user
provided)
DSL Modem Mounting Plate
Phone Svc
to house
DSL Svc to
house
Data Surge
Conditioning
Unit
Ground wire and screw
INSTRUCTION/INSTALLATION SHEET
DSL MODEM MOUNTING PLATE IS-0308 REV. O
Page 2 of 2
301 Fulling Mill Road, Suite G ©Copyright 2005 by OnQ Technologies, Inc All Rights Reserved.
Middletown, PA 17057 www.onqhome.com
(800)-321-2343
Innovations in Home Living.
3. Installation
The On-Q Home DSL Modem Mounting Plate is typically installed during “trim-out” or as an upgrade for an existing
installation.
a. Place the DSL modem on the mounting plate with its port connections pointing towards the DSL splitter end of the
mounting plate and secure using the two provided Velcro straps.
b. Align two stationary tabs on the mounting plate with slots on the back of the enclosure (see Figure 2).
c. Insert tabs by angling module away from the back of the enclosure and sliding forward (see Figure 2).
d. Rotate the mounting plate and insert the built in locking
tab on the mounting plate into the corresponding hole on
the back of the enclosure, pushing in until it snaps into
place (see Figure 2).
e. Pull lightly on the module to assure it is properly locked in
place.
f. The CAT5e cable from the DSL/phone service provider is
run to the input of the DSL Splitter Conditioning Unit.
g. The provided jumper is run from the DSL port of the DSL
Splitter Conditioning Unit to the input connector on the
DSL modem.
h. For P/N 364808-12, run the provided CAT5e jumper from
the Ethernet output of the DSL modem to the input of the
Data Surge Conditioning Unit, and another jumper from
the output of the Data Surge Conditioning Unit to the data
distribution device for the house (router, etc.).
i. Connect the provided ground wire to the mounting plate
with the provided screw, and run the other end of the
ground wire to house ground.
Figure 2
  • Page 1 1
  • Page 2 2

Legrand DSL Modem Mounting Plate - 364808-11 / 364808-12 Installation guide

Legrand
Brand
Legrand
Model
DSL Modem Mounting Plate - 364808-11 / 364808-12
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents