Legrand Modem Mounting Plate, Cable, Data Surge, IS-0298 Installation guide

Legrand
Brand
Legrand
Model
Modem Mounting Plate, Cable, Data Surge, IS-0298
Type
Installation guide

This manual is also suitable for

Legrand Modem Mounting Plate, Cable, Data Surge, IS-0298 is designed to easily mount a Cable modem inside an On-Q Home enclosure. This device comes with two versions, P/N 364808-01 and 364808-02. Both versions include a splitter, two cable modem mounting straps, two coax jumpers, a ground wire and screw. The P/N 364808-01 version additionally includes a Data Surge Conditioning Unit and a Cat5e jumper. This device is easy to install and can be typically installed during “trim-out” or as an upgrade for an existing installation.

Legrand Modem Mounting Plate, Cable, Data Surge, IS-0298 is designed to easily mount a Cable modem inside an On-Q Home enclosure. This device comes with two versions, P/N 364808-01 and 364808-02. Both versions include a splitter, two cable modem mounting straps, two coax jumpers, a ground wire and screw. The P/N 364808-01 version additionally includes a Data Surge Conditioning Unit and a Cat5e jumper. This device is easy to install and can be typically installed during “trim-out” or as an upgrade for an existing installation.

INSTRUCTION/INSTALLATION SHEET
CABLE MODEM MOUNTING PLATE IS-0298 REV. O
Page 1 of 2
301 Fulling Mill Road, Suite G ©Copyright 2005 by OnQ Technologies, Inc All Rights Reserved.
Middletown, PA 17057 www.onqhome.com
(800)-321-2343
Innovations in Home Living.
1. Introduction
The On-Q Home Cable Modem Mounting Plate is designed to easily mount a Cable modem inside an On-Q Home
enclosure, and is available as two different versions (P/N 364808-01 and 364808-02) as shown and described below. The
Data Surge Conditioning Unit, shown as part of the P/N 364808-01 version, may also be ordered as a standalone product
(P/N 364598-01).
2. Description
The On-Q Home Cable Modem Mounting Plate, (see Figure 1-2) is designed to be mounted in an On-Q Home enclosure,
with two tabs on one end and a locking tab on the other. The two versions contain the following components:
P/N 364808-01 version P/N 364808-02 version
1 Data Surge Conditioning Unit 1 Splitter
1 Splitter 2 Cable modem mounting straps
2 Cable modem mounting straps 2 Coax jumpers
1 Cat5e jumper 1 ground wire and screw
2 Coax jumpers
1 ground wire and screw
Mounting
Straps
Data Surge
Conditioning
Unit
Figure 1
Data Svc
to house
Cable
Modem
(user
provided)
Cable Modem
Mounting Plate
CATV Svc to house
CATV + Data Svc in
Ground wire
and screw
Splitter
INSTRUCTION/INSTALLATION SHEET
CABLE MODEM MOUNTING PLATE IS-0298 REV. O
Page 2 of 2
301 Fulling Mill Road, Suite G ©Copyright 2005 by OnQ Technologies, Inc All Rights Reserved.
Middletown, PA 17057 www.onqhome.com
(800)-321-2343
Innovations in Home Living.
3. Installation
The On-Q Home Cable Modem Mounting Plate is typically installed during “trim-out” or as an upgrade for an existing
installation.
a. Place the Cable modem on the mounting plate with its port connections pointing towards the Data Surge Conditioning
Unit end of the mounting plate and secure using the two provided Velcro straps.
b. Align two stationary tabs on the mounting plate with slots on the back of the enclosure (see Figure 2).
c. Insert tabs by angling module away from the back of the enclosure and sliding forward (see Figure 2).
d. Rotate the mounting plate and insert the built in locking
tab on the mounting plate into the corresponding hole on
the back of the enclosure, pushing in until it snaps into
place (see Figure 2).
e. Pull lightly on the module to assure it is properly locked in
place.
f. The RF coax cable from the cable provider is run to the
input of the splitter.
g. A coax jumper is run from one of the outputs of the splitter
to the RF coax connector on the cable modem.
h. Another coax jumper is run from the other output of the
splitter to the input of the video distribution device used for
the house.
i. For P/N 364808-01, run the provided CAT5e jumper from
the Ethernet output of the cable modem to the input of the
Data Surge Conditioning Unit, and another jumper from
the output of the Data Surge Conditioning Unit to the data
distribution device for the house (router, etc.).
j. For P/N 364808-01 and -02, connect the provided ground
wire to the mounting plate with the provided screw, and
run the other end of the ground wire to house ground.
Figure 2
  • Page 1 1
  • Page 2 2

Legrand Modem Mounting Plate, Cable, Data Surge, IS-0298 Installation guide

Legrand
Brand
Legrand
Model
Modem Mounting Plate, Cable, Data Surge, IS-0298
Type
Installation guide
This manual is also suitable for

Legrand Modem Mounting Plate, Cable, Data Surge, IS-0298 is designed to easily mount a Cable modem inside an On-Q Home enclosure. This device comes with two versions, P/N 364808-01 and 364808-02. Both versions include a splitter, two cable modem mounting straps, two coax jumpers, a ground wire and screw. The P/N 364808-01 version additionally includes a Data Surge Conditioning Unit and a Cat5e jumper. This device is easy to install and can be typically installed during “trim-out” or as an upgrade for an existing installation.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents