HySecurity OLED Display Board Operating instructions

HySecurity
Brand
HySecurity
Model
OLED Display Board
Type
Operating instructions

HySecurity OLED Display Board

The HySecurity OLED Display Board is a high-quality replacement display for your HySecurity control box. This display is easy to install and comes with all the necessary hardware. It features a bright, easy-to-read OLED display that will show you all the important information about your gate operator, including the status of the gate, the time, and any error messages.

The OLED Display Board is also compatible with all HySecurity gate operators, so you can be sure that it will work with your system. It is also backed by a 1-year warranty, so you can be sure that it will last.

HySecurity OLED Display Board

The HySecurity OLED Display Board is a high-quality replacement display for your HySecurity control box. This display is easy to install and comes with all the necessary hardware. It features a bright, easy-to-read OLED display that will show you all the important information about your gate operator, including the status of the gate, the time, and any error messages.

The OLED Display Board is also compatible with all HySecurity gate operators, so you can be sure that it will work with your system. It is also backed by a 1-year warranty, so you can be sure that it will last.

Page 1 www.hysecurity.com © 2014 P/N MX3542 D0629 Rev A
Installation Instructions
MX3542
Smart Touch Controller (OLED) Display
To replace the display in the control box with the OLED display kit, take the
following steps:
1. Turn OFF power to the control box and open the control box lid.
2. Disconnect the ribbon cable and keypad cable.
3. Strip the keypad membrane o the top of the control box lid.
4. Using a Phillips-head screwdriver, remove the four screws that secure the
display board to the control box lid. Note the orientation of the board so
you can align the holes in the replacement display board assembly with the
mounting standos.
5. Remove the adhesive backing on the keypad membrane MX3399.
6. Feed the keypad cable through the cutout in the control box lid while you
securely press the keypad membrane into place on the lid. Refer to page 2.
7. Reattach the ribbon cable and keypad cable.
NOTICE: Make sure there are no twists in the ribbon cable. Do not force a ribbon
cable’s connection. e connectors are keyed so if it is dicult to connect, reassess the
alignment as it will only go in one way.
8. Secure the replacement display board assembly using the screws removed in
step 4.
9. Close the control box lid.
10. Turn ON power to the control box.
11. Test the keypad buttons and view the new display.
Display Board
MX000678 or
MX3356 (2014)
Ribbon cable from display
board to STC board
MX000046
Phillips-head screws (4x)
Power
switch
Disconnect the ribbon
cable and keypad cable
before removing the
display board.
Mounng standos
Control box
Keypad cable
Control box lid
Page 2 www.hysecurity.com © 2014 P/N MX3542 D0629 Rev A
ot 3
ot 1
Hydraulic Gate Operator Type Displays
Hydraulic Gate Operator Display: MX3399
Display/keypad introduced in 2014. The retro-t kit
MX3542 creates in-eld compability between the
control box and display/keypad.
HYSECURITY
GATE STOPPED
Display Board
MX3356
Keypad membrane
MX3399
Feed keypad cable from
keypad membrane to
display board connecon.
Keypad cable
1. Peel away the old keypad from
the control box lid.
2. Replace it by removing the label
backing and exposing adhesive.
3. Firmly place keypad membrane
on the control box lid.
OLED display
assembly kit
MX3542
  • Page 1 1
  • Page 2 2

HySecurity OLED Display Board Operating instructions

HySecurity
Brand
HySecurity
Model
OLED Display Board
Type
Operating instructions

HySecurity OLED Display Board

The HySecurity OLED Display Board is a high-quality replacement display for your HySecurity control box. This display is easy to install and comes with all the necessary hardware. It features a bright, easy-to-read OLED display that will show you all the important information about your gate operator, including the status of the gate, the time, and any error messages.

The OLED Display Board is also compatible with all HySecurity gate operators, so you can be sure that it will work with your system. It is also backed by a 1-year warranty, so you can be sure that it will last.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents