LAMONA LAM9550 Installation guide

LAM9550
LAMONA
Brand
LAMONA
Model
LAM9550
Type
Installation guide

The LAMONA LAM9550 is a versatile two-in-one appliance that combines a sleek ceramic hob with a powerful cooker hood, offering you the ultimate convenience in your kitchen. Equipped with four cooking zones, this hob provides ample space for preparing multiple dishes simultaneously, while the integrated hood effectively removes smoke, odors, and grease, leaving your kitchen fresh and clean.

The LAMONA LAM9550 is a versatile two-in-one appliance that combines a sleek ceramic hob with a powerful cooker hood, offering you the ultimate convenience in your kitchen. Equipped with four cooking zones, this hob provides ample space for preparing multiple dishes simultaneously, while the integrated hood effectively removes smoke, odors, and grease, leaving your kitchen fresh and clean.

33
Exclusive to Howdens
6.ModicationsforacombinationhobHood-1000mmcabinet(900minimum)
250mm
35mm
120mm
*
Set up for standard or handleless kitchens
is the same.
Avoid the cabinet legs.
For illustrative purposes the
frontal option has been shown.
Variations for the drawer
option are detailed separately.
Read all stages before
modifying the cabinet.
1 Remove the back panel
Keep the back panel for later use.
2 Modify base
Cut out a section in the bottom shelf for
ducting (* to suit position of hob and ducting).
*Dimensions are guides only.
34 www.howdens.com
122mm
160mm
4x 30mm wood screw
(not supplied)
Support panel
Fit support panel ush with the
top of the cabinet.
Secure with KD blocks and side
screws.
Remove c.122mm (140-18), the height
of the support panel) from centre upright.
3 Make front support panel
The support panel will be visible when
complete, therefore we recommend using
a decor panel of some sort.
Support
panel
Profile
140mm
Secure into the top
of the cabinet, flush
with top edge
Screw
(4x30mm)
C.20mm
20mm+
160mm
Remove front rail.
HandlelessKitchen(Prole)
6.Modicationsforacombinationhobhood-1000mmcabinet (900 minimum)
Remove c.122mm (140-18), the height
of the support panel) from centre upright.
35
Exclusive to Howdens
Remove c.122mm (140-18), the height
of the support panel) from centre upright.
5 Fit back panel supports to cabinet sides
2 x 560mm
1 x 440mm 30mm
30mm
The cut down pieces of rail are used to hold
the back panel in place.
114mm
30mm Wood scre
w
(not supplied)
Don’t cover the gap that has been cut for the ducting.
Remove c.122mm (140-18), the height
of the support panel) from centre upright.
4 Remove and cut down back rail Avoid metal tangs on wider cabinets.
Support panel
Insert batten at the
back of the cabinet
to support worktop.
Remove back rail and split into 3 long
sections shown below.
36 www.howdens.com
6.Modicationsforacombinationhobhood-1000mmcabinet (900 minimum)
6 Fit back panel.
Cut down the back panel and screw to
newly tted support rails.
30mm Wood screw
(not supplied)
964mm
540mm
Fitting with frontals A new hinge hole will need to be drilled into
the door at the dimensions shown below.
Fit cover cap
in original hole
468.5mm
22.5mm
22.5mm
21.5mm
31mm
Ø35mm x 12mm
37
Exclusive to Howdens
6.Modicationsforacombinationhobhood(1000mmcabinet, 900 minimum)
Fit cover cap
in original hole
Note: Use bump-ons to
maintain correct
alignment.
Fix the dummy drawer
frontal onto the support
panel from inside the
cabinet using suitable
screws.
Fitting with 3 drawers Follow previous steps 1- 6, ignoring centre post modication.
Example drawer runner installation.
Dummy Drawer Front
Support Panel
160 Dummy
275
275
170
Dummy
170
342
Standard        Handleless(Prole)
2 Drawer Option: 2 x 356mm frontals (LAM9550).
• Top drawer must be a cutlery drawer box (max. weight 30Kg) due to lower rear wall.
• Lower drawer will be a pan drawer box.
SeeHowdensKitchenInstallationManualfordrawerxingandrunnerinstallation.
436mm
62mm
27mm
59mm
337mm
27mm
SeeHowdensKitchenInstallationManualfordrawerxingandrunnerinstallation.
38 www.howdens.com
(A) Recirculation air (B) Extraction air
Plinth
Vent
APL 2807
APL 2000
LAM 2013
6. Installation - Air extraction system assembly
Congureventkitstosuitapplication.
Shown above using parts from
LAM2013, APL2000 and APL2807
Product vent size
222mm
89mm
Side view cabinet (B)Side view cabinet (A)
External venting: Adapt to suit (B)
Use LAM2013 kit.
Ensure plinth vent is used.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

LAMONA LAM9550 Installation guide

LAM9550
LAMONA
Brand
LAMONA
Model
LAM9550
Type
Installation guide

The LAMONA LAM9550 is a versatile two-in-one appliance that combines a sleek ceramic hob with a powerful cooker hood, offering you the ultimate convenience in your kitchen. Equipped with four cooking zones, this hob provides ample space for preparing multiple dishes simultaneously, while the integrated hood effectively removes smoke, odors, and grease, leaving your kitchen fresh and clean.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents