2. Computers & electronics
  3. TVs & monitors
  4. Flat panel desk mounts
  5. Atdec
  6. Freestanding Quad
Freestanding Quad

Atdec Freestanding Quad, V-FS-Q Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Atdec Freestanding Quad Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is the maximum weight that each Donut Clamp Assembly can support?
    What VESA compliant display mounting hole patterns does this product suit?
    What tools are required for installation?
    How do I adjust the position of the Donut Clamps?
    How do I adjust the Ball Joint Mechanism?
Component Checklist
Bits Box
Important Notes
l
Each Donut Clamp Assembly supports a maximum weight of 11.5kg (25lbs)
l
This product suits VESA compliant displays with 75mm x 75mm (3” x 3”) and
100mm x 100mm (4” x 4”) mounting hole patterns.
l
The manufacturer does not accept responsibility for incorrect installation
freestanding quad
Installation Instructions
visidec
Check you have received all parts against this component checklist prior to installation
Cable
Ball (x8)
M8x50mm
Screw
(x1)
Cable
Clip (x4)
Extension
Clip (x16)
2.5mm Allen
Key (x1)
5mm Allen
Key (x1)
Mounting Screws
M4x10 mm (x16)
M4x12mm (x16)
M4x16mm (x16)
TOOLS REQUIRED:
l
Phillips Head Screw Driver
A
Attach Upright Pole to Base Install Horizontal Support and Donut Clamp
Attach the Upright Pole to the Base
as shown below. Ensure the Cable
Slot faces towards the rear.
Follow steps below to attach the Horizontal Support and Donut Clamp
assembly onto the Upright Pole. Ensure the Cable Slots in all the Poles are
facing to the rear.
Horizontal
Support Donut(x1)
Donut
Clamp (x4)
Upright Pole
Base
B
B.2.
Slide the Horizontal Support
to desired position
Cable
Slot
Cable Slot
User
Upright Pole
Back
LOOSEN
LOOSEN
TIGHTEN
POSITION
Repeat steps B.1, B.2 and B.3
for the 2nd set of Horizontal
Support and Donut Clamp
TIGHTEN
B.1.
Loosen the Hex screws in the
Horizontal Support Donut using
the supplied 5mm Allen Key
B.3.
Tighten supports firmly
using the supplied 5mm
Allen Key
5mm Allen Key
M8x50mm Screw
TIGHTEN
FIRMLY
IMPORTANT:
When tightening the Donut Clamp,
each of the Donut bolts must be
tightened evenly, as failure to do so
will damage the Donut Clamp. Do
not over-tighten as this may also result
in damage.
Adjust Ball Joint Mechanism
E
As LCD Manufacturers are constantly releasing new monitor models, Atdec does not accept responsibility it the mounting hole pattern does not comply with the international VESA standards.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 29.08.07©
Adjust Donut Clamps
C
Mount Displays
D
Cable Management
F
100mm (4”)
75mm (3”)
100mm
(4”)
75mm
(3”)
LOOSEN
TIGHTEN
Adjust the Ball Joint
Mechanism to suit the
weight of your display.
Tighten or loosen
screws evenly with the
supplied 2.5mm Allen
Key, 1/4 turn at a time.
2.5mm
Allen Key
Cable
Balls
Cable
Clips
IMPORTANT:
When tightening the Donut
Clamp, each of the Donut
bolts must be tightened
evenly, as failure to do so will
damage the Donut Clamp.
Do not over tighten as this
may also result in damage.
Choose the correct Mounting Screws supplied in the bits
box and attach the display as shown.
Note: Extension
Clips are included
to suit VESA 100mm
x 100mm (4” x 4”)
Mounting Hole
Patterns.
Follow steps below to adjust the position of Donut Clamps. Ensure the Cable Slots
in all the Poles are facing to the rear.
LOOSEN
POSITION
TIGHTEN
C.1.
Loosen Donut Bolts evenly
using the supplied 5mm
Allen Key
C.2.
Slide the Donut Clamp to
desired position
C.3.
Tighten Donut Bolts firmly
using the supplied 5mm
Allen Key
Note: Ensure enough
slack is left in cables to
allow for movement.
Insert display cables into the slots in each pole, using
Cable Balls to hold them in place.
Note: When the slot in each pole cannot be used, use
the supplied Cable Clip’s to secure the display cables.
/