Atdec Visidec Freestanding Double Installation guide

Atdec
Brand
Atdec
Model
Visidec Freestanding Double
Type
Installation guide
Attach the Upright Pole to the Base Plate as shown
below. Ensure the Pin in the Base Plate lines up
with the hole in the
Pole Collar.
A Component Checklist - Check you have received all parts against the component checklist prior to installing
Installation Instructions
Upright Pole
Bits Bag
M8x50mm Screw
Cable Clip (x4)
5mm Allen
Key
Display Mounting
Screws
M4x16mm
(x8)
M4x12mm
(x8)
M4x10mm
(x8)
C Attach Horizontal Support’s
Extension Clips (x8)
M6x12mm Cap
Screw (x2)
2.5mm Allen
Key
Pole Collar
Donut
Clamps (x2)
Horizontal Support (x2)
Base Plate
Tighten “Donut” Hex screws
firmly
and
evenly
.
DO NOT OVER TIGHTEN!
x
Position the Horizontal Supports at
the required height on the Upright
Pole. Ensure the Slots in all the Poles
are facing backwards.
Tighten supports using the
M6x12mm Cap Screws, M6 Donut
Inter-Screws and 5mm Allen Key
supplied. Take care to tighten clamp
firmly
and
evenly!
Upright Pole
Pole Collar
Base
Plate
B Attach Upright Pole to Base
Pin
TIGHTEN
FIRMLY
M8x50mm Screw
5mm Allen Key
M6x12mm
Cap Screw
(x2)
Slot in Poles to
face back
TIGHTEN
FIRMLY
Cable Balls (x6)
Locating
Hole
M6 Donut
Inter-Screw
(x2)
HOLD IN
PLACE
M6 Donut
Inter-Screw (x2)
Slot in Poles to
face back
F Adjust Ball Joint Mechanism
As LCD Manufacturers are constantly releasing new monitor models, Atdec does not accept responsibility if the mounting hole pattern does not comply with the international VESA
standards. Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 08.12.06 ©
G Cable Management
D Attach Donut Clamps
1. Loosen both Donut Bolts evenly using the 5mm
Allen Key supplied.
2. Slide Donut Clamps over each Pole.
3. Adjust position of Donut Clamps to suit your
displays, then tighten screws
firmly
and
evenly
.
WARNING : DO NOT OVER TIGHTEN!
Tilt Ball Mechanism to access Donut Bolt.
Donut
Bolt
Donut
Bolt
E Mount Displays
Adjust the Ball Joint Mechanism to suit the weight of
your display. Tighten or loosen screws 1 to 4 evenly,
1/4 turn at a time.
LOOSEN
TIGHTEN
Extension
Clips (x4)
75mm
(3”)
75mm
(3“)
100mm
(4”)
100mm
(4”)
or
4
1
2
2.5mm Allen Key
3
2
3
1
LOOSEN
For Displays with 75mm x 75mm (3” x 3”) mounting
hole patterns.
USE
M4 x 10mm
screws
For Displays with 100mm x 100mm (4” x 4”) mounting hole
patterns.
USE
M4 x 12mm or
M4 x 16mm
Cable
Clip’s
(x4)
Cable
Balls (x6)
Leave enough
slack in the
cables to allow
for movement.
Insert display cables into the slots in each
pole, using Cable Balls to hold them in place.
NOTE: When the slot in each pole cannot be
used, use the supplied Cable Clip’s to secure
the display/s cables.
  • Page 1 1
  • Page 2 2

Atdec Visidec Freestanding Double Installation guide

Atdec
Brand
Atdec
Model
Visidec Freestanding Double
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents