Product manual | Version 1.0.1

WAGO Cloud

Application “WAGO Cloud Building Operation and Control”

Legal Information

© 2021 WAGO Kontakttechnik GmbH & Co. KG

All rights reserved.

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D - 32423 Minden

Fax: +49 571/887 – 844555

E-Mail: * [email protected]

Every conceivable measure has been taken to ensure the accuracy and completeness of

this documentation. However, as errors can never be fully excluded, we always appreci-

ate any information or suggestions for improving the documentation.

E-Mail: * [email protected]

We wish to point out that the software and hardware terms as well as the trademarks of

companies used and/or mentioned in the present manual are generally protected by

trademark or patent.

WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.

Table of Contents

1.3 Legal Information .................................................................................................... 7

2.1 General Safety Regulations .................................................................................... 8

2.2 Indirect Safety ......................................................................................................... 8

4.1 Activation............................................................................................................... 10

5.1 Start the Application .............................................................................................. 11

5.2 Launch the Application.......................................................................................... 11

6.1.2 Action Area...................................................................................................17

6.1.2.1 Action Area – Complete View..............................................................19

6.1.2.2 Action Area – Detail View ....................................................................23

7.1 Create New Key Performance Indicator................................................................ 33

7.2 Edit or Delete Existing Key Performance Indicator ............................................... 34

Observe the applicable documentation!

This documentation is part of the complete Instructions for use for the application “WAGO

Cloud Building Operation and Control”. The product may only be operated in accordance

with the complete Instructions for use. Knowledge of the complete Instructions for use is

a precondition for intended use.

All the documentation is available at: üwww.wago.com/cloud.

WAGO Cloud is a universal IoT solution for machines, systems and buildings for:

• Centralized Collection and Analysis of Data

• Monitoring and managing devices, including your data (e.g, WAGO controllers)

• Visualizing and comparing machines and system data

• Remote access to local configurations and visualizations

• User and group management

Improper Use

Improper use of the products is not permitted. Specifically, improper use occurs in the fol-

Warranty and Liability

The terms set forth in the General Business & Contract Conditions for Delivery and Ser-

vice of WAGO Kontakttechnik GmbH & Co. KG and the terms for software products and

products with integrated software stated in the WAGO Software License Contract – both

available at üwww.wago.com – shall apply. In particular, the warranty is void if:

• The products are used improperly.

• The deficiency (hardware and software configurations) is due to special instructions.

• Modifications to the hardware or software have been made by the user or third parties

that are not described in this documentation and that has contributed to the fault.

Individual agreements always have priority.

Obligations of Installers/Operators

compliance, the products may not be operated within the scope of the approval.

Number Notation

Text Formatting

Action Instructions

1. Action step

Type and source of hazard

Possible consequences of hazard that also include death or irreversible injury

Type and source of hazard

Possible consequences of hazard that also include severe injury

Graphical User Interface

6.1.1 Side Menu

Graphical User Interface

6.1.2 Action Area

The action area has two different views:

Complete view

This view contains a complete overview of all subordinate properties. Performance indi-

cators for complete areas can be viewed and reports can be created. Specific parameters

can be configured. All individual properties are also listed.

The complete view is identified by a “directory” icon (see Section 8Action Area – Com-

View [}23]).

Regardless of the selected view, the action area can be divided into two areas:

Graphical User Interface

Graphical User Interface

There is a button in the menu bar that can be used to select one of two modes. The but-

ton has two presentations:

For complete areas of properties, recorded performance indicators can be viewed and

parameters can be configured in this action area. Reports can also be created.

The menu bar has the following tabs:

6.1.2.1.2.1 “Overview” Subarea

This subarea is called up from the “Overview” tab.

The individual tabs are described in the Section 8Menu Bar [}19].

The subarea can be divided into two views:

Graphical User Interface

“Status” Single View

The subordinate properties can be monitored in the “Status” single view. The monitoring

refers to the key performance indicators of individual building systems that are available

for the respective property.