FOAM GUN FOR EXPANDING FOAM
CARTRIDGES
MODEL NO: FG001
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9 Always read the foam and cleaner manufacturers’ instructions when handling and using their product in conjunction with this gun.
9 Only use the gun in adequately ventilated rooms with the correct respiratory protection equipment
9 Manyfoamproductscontainhighlyinammablechemicals,DO NOTuseintheproximityofanyopenames,cigarettesoranyother
potentialcauseofcombustion
9 Alwayswearapprovedsafetyclothingandpersonalprotectionequipment:gloves,gogglesforeyeprotection,amaskwiththe
appropriateactivatedcarbonlterswhenworkingwiththefoamgun.
9 Keep the gun out of the reach of children.
9 Maintaintheguningoodcondition.Replaceorrepairdamagedparts.Userecommendedpartsonly.Unauthorisedpartsmaybe
dangerous and will invalidate the warranty.
9 Keepchildrenandunauthorisedpersonsawayfromtheworkarea.
9 Avoid unintentional operation.
8 DO NOTholdgunorattachmentsclosetoyourface(especiallyeyes,ears,etc.)andDO NOT point gun at other persons or animals.
8 DO NOT use the gun for any purpose other than that for which it is designed.
8 DO NOT operate the gun if damaged.
9 Whennotinusestoreinasafe,dry,childproofarea.
2. INTRODUCTION
Atopqualitymetalgunforusewithgungradepolyurethaneexpandingfoams.Screwsontothecanisterforquickandeasyapplication.Easy
foamgunforexpandingfoamadjustableowcontrol.Stainlesssteelbarrelandneedle.
3. SPECIFICATION
Model No.: .................................................................. FG001
4. OPERATION
4.1. Alwaysinspectthegunbeforeusetoensureitisnotdamaged.If
indoubtdonotusethegunandcontactyourSealeyStockist.
4.2. Shakecanvigorouslyfor30secondspriortoinstallingontofoamgun.
4.3. Makesurethegunbasketisperfectlycleanandapplysomepetro-jelly
orlightgreasetotheinsideofthegunbasketarea.Thishelpsprevent
foamfromcuringtothebasketandgluingthecanontothegun.
4.4. Screw the cartridge onto the gun’s adaptor until it is tight. DO NOT over
tighten as this may cause damage to the threads.
4.5. Pullthetriggertostartthefoamow,thismayberegulatedbythebeadsizeadjusteruntilthedesiredfoambeadisachieved
4.6. Releasethetriggerandtightenthesizeadjustertolocktheneedleintheclosedposition,topreventaccidentaldischargewhen
the gun is not in use.
4.7. Always store the gun with the can attached in the normal use position.
4.8. Replaceemptycartridgesassoonaspossibletoavoidhardeningofthefoaminthegun.
4.9. Tore-use,simplyshakethefoamcanvigorouslyfor30seconds.
4.10 Whenthecartridgeisemptiedunscrewitoutofthefoamgunsocket.Cleanpossibledirtwithcleanserandscrewnewcartridgein.
5. MAINTENANCE
5.1. Ifthegunisnottobereloadeditmustbecleanedassoonaspossibleafterthecartridgehasbeenremovedtoavoidhardeningof
the foam inside the gun.
5.2. Oncethefoamhasbecomehardsolventswillnotnecessarilydissolveallresidues.
5.3. Alwaysensureallfoamisreleasedfromthegunbeforecleaning.
8 DO NOT use water to clean the gun.
5.4. Onlycleanthegunwithrecommendedcleaningsolvents,anyothersolventsmaydamagethegun.
5.5. Leavethesolventinthegunfor2minutes.Releasethesolventbypressingthetriggerandrepeatthisprocessuntilthesolvent
FG001Issue110/06/22
Original Language Version
©JackSealeyLimited
Refer to
instructions
g.1
Wear eye
protection
Wear protective
gloves
Wear Face
Mask
(Filtered)
BeadSizeAdjuster