FAST FIX FILLER & ADHESIVE
MODEL NO’S: SCS906, SCS908, SCS909, SCS910
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this tool.
WARNING! Familiarise yourself with the specic applications and limitations of the product as well as any potential hazards.
WARNING! This kit contains glue. If you require a safety data sheet , contact your Sealey stockist.
9Keep out of reach of children. Store locked away.
9May cause respiratory irritation. Only use outdoors in a well ventilated area.
9Wear protective gloves/protective clothing/eye protection/face protection.
WARNING! Chemical reaction created by the powder and the glue could burn skin.
WARNING! Avoid contact with skin. IF ON SKIN wash with plenty of soap and water. Release stuck skin with acetone.
WARNING! Avoid contact with eyes. IF IN EYES rinse cautiously with water for several minutes. Remove contact lenses if present and
easy to do. Continue rinsing. If eye irritation persists get medical advice/attention.I
9Keep children, animals and unauthorised persons away from the work area.
8DO NOT use if you are tired or under the inuence of alcohol, drugs or intoxicating medication.
2. INTRODUCTION
Two part (adhesive and ller power) repair system with unique reinforcing and lling feature. Cracks, holes and gaps can be repaired so that the
damaged area is taken beck to the original shape/prole. Designed to bond rubber, copper, steel and aluminium as well as most plastics. Rapid
solidication and strong cohesive force allows speedy repairs - under 30 seconds and you can move on to the next stage of the repair.
3. PREPARATION
3.1. Decide what kind of repair is to be made. If necessary arrange appropriate supporting materials: masking tape, cleaning cloths.
3.2. Prepare all tools and accessories required for the whole repair.
WARNING! Direct contact with the glue is not allowed.
4. INSTRUCTIONS
4.1. STEP 1
4.1.1. Wear protective gloves.
4.1.2. Clean o surface paint, dust and oil. Ensure area is clean and dry. Use sandpaper to roughen the surface.
4.2. STEP 2
4.2.1. Unscrew lid from powder container. Use a knife to carefully cut the powder container nozzle at a 45° angle and put aside.
4.2.2. Use pin (supplied) to pierce the adhesive bottle’s nozzle. Fit the adhesive catheter tightly onto the nozzle.
4.3. STEP 3
4.3.1. Drop the adhesive evenly onto the site of the repair.
4.3.2. Drop an appropriate amount of powder (thickness ≤ 5mm) onto the site of the repair. Use the supplied stirrer to adjust the powder
shape and dosage.
4.3.3. Drop adhesive again on to the powder, until the powder will no longer absorb the adhesive.
WARNING! The adhesive combined with the powder will produce a lot of heat and slight irritant gases within 10 seconds.
4.4. If the repair is not thick enough repeat step 3.
Refer to
instruction
manual
Wear
protective
gloves
Wear eye
protection
Wear a mask
SCS906, SCS908, SCS909, SCS910 Issue:2 (4) 11/01/22
Original Language Version
© Jack Sealey Limited
1
2
Sealey AK46KIT User manual
Sealey sga1.V4 Operating instructions
Sealey SGA1 Oxyacetylene Welding and Cutting Set Operating instructions
Sealey SDL15 User manual
Sealey TIG130 User manual
Sealey AB936 User manual