DELUXE GAS WELDING GOGGLES
MODEL NO: SSP5D
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9 Inspect the goggles frequently as a pitted or scratched face shield reduces vision and should be replaced immediately.
8 DO NOT use if any part of the goggles is cracked or broken.
8 DO NOT place this product on a hot surface.
9 Ensure that the goggles are in place before entering the hazard area.
2. INTRODUCTION
Shade 5 deluxe welding lens with indirect ventilation in goggle frame. Suitable for gas welding. Conforms to EN 175 & EN 169.
3. SPECIFICATION
Model No: .................................................................. SSP5D
Shade ..................................................................................5
4. ASSEMBLY
NOTE: It is imperative that the goggles t well and comfortably for the user or else slippage and discomfort may arise.
4.1. Adjust the headband by pulling/loosening the headband through the buckle.
5. USE
5.1. Ensure goggles t comfortably over eyes. Protection will only be oered if the goggles are tted correctly.
5.2. The frame when in contact with the skin may cause allergic reactions to susceptible individuals. If this is the case doctor’s advice
should be consulted.
8 DO NOT apply paint, solvents, adhesives or self adhesive labels except in accordance with manufacturer.
5.3. The housings of these eye protectors provide less protection against impact than the lens.
5.4. These goggles may transmit impacts to eyewear enclosed by the goggles.
6. CLEANING & DISINFECTION
6.1. Rinse in 1% solution of mild detergent and dry with a soft cloth.
8 DO NOT use abrasive cleaners
7. MAINTENANCE
7.1. The goggles should be periodically inspected and cleaned.
7.2. If the lens becomes damaged or scratched the goggles should be replaced.
8. STORAGE
8.1. Store in a bag or case out of direct sunlight, away from chemicals, away
from hard and abrasive substances, in a clean dust free environment.
Use original bag for transportation if possible.
9. SHELF LIFE/EXPIRY DATE
9.1. Under normal circumstances the goggles should oer adequate protection
for 5 years.
SSP5D Issue 1 11/05/21
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of
disposing of them as waste. All tools,
accessories and packaging should
be sorted, taken to a recycling centre
and disposed of in a manner which is
compatible with the environment. When the
product becomes completely unserviceable
and requires disposal, drain any fluids (if
applicable) into approved containers and
dispose of the product and fluids according
to local regulations.
1
Sealey SGA1 Oxyacetylene Welding and Cutting Set Operating instructions
Sealey PWH600.V2 User manual
Sealey PWH615 User manual
Sealey TS01.V2 User manual
Sealey CP1210 User manual
Sealey OS600 User manual