Classic Exhibits VK-2920 Setup Instructions

Brand: Classic Exhibits

Model: VK-2920

Type: Setup Instructions

www.classicexhibits.com

Step 1

Page 1 of 9

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - VK-2920 General Layout

Plan View

Elevation View

Perspective View

20’

10’

www.classicexhibits.com

Step 2

Page 2 of 9

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - General Information

The Tool Typical Connection

Horizontal Inline Connection (remove only one setscrew)

Base Plate Connection Vertical Connection

(remove only two setscrews)

Most Visionary Designs exhibits can be

assembled with the supplied Hex Key Tool.

Occasionally, a flat head screwdriver may

be required.

Most horizontal extrusion connections have a patented expandable lock. This lock inserts into

the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock

and creates a strong positive connection.

Remove only (1) setscrew when disassembling. Replace setscrew in

extrusion after assembling it. Before packing, replace setscrew in

extrusion to avoid losing it.

Attach base plate to round or square

vertical extrusion using the bolt provided.

Be careful not to strip the threads.

When vertical extrusions are packed in

portable cases rather than crates or

tubs, they must broken down into

smaller sections which then require

assembly.

Remove only (2) setscrews when

disassembling. Replace setscrews in

extrusion after assembling it. Before

packing, replace setscrews in extrusion

to avoid losing them.

Using Your Setup Instructions

The Visionary Designs Setup Instructions are created specifically for your

configuration. They are laid out sequentially, including an exploded view of

the entire display, and then a logical series of detailed steps to assemble the

main structure and components. We encourage you to study the instructions

before attempting to assemble your exhibit.

Each page reminds you to tighten the setscrews after disassembling your

exhibit to prevent loss of the locks and setscrews (see below in RED).

This is VERY IMPORTANT.

Cleaning and Packing Your Display

1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only

non-abrasive cleaners.

2) When cleaning laminate inserts or countertops, use mild cleansers and a

soft material such as cotton.

3) Keep all display components away from extreme heat and long exposure

to sunlight to avoid warping and fading.

4) Retain all packing material. It will make re-packing much easier and will

reduce the likelihood of shipping damage.

Typical Connection (cont’d)

Numbered Label

Each extrusion contains a numbered label which

corresponds with setup instructions.

The label is located within a groove of the extrusion

(when possible). With Visionary Designs the labels

contain Black numbers unless otherwise specified.

Detail C E liateDD liateDDetail B

Detail A

Setscrews

www.classicexhibits.com

Step 1

Page 1 of 9

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - Backwall Assembly

Steps:

1) Attach lower

vertical extrusions [2,3,6] to base plates [1].

2) Attach upper vertical extrusions to lower vertical extrusions as shown.

3) Connect horizontal extrusions between vertical extrusions as shown.

4) Apply graphics to velcro on back of assembled backwall.

Item Qty Description

1 3 Base Plate

2/2a 1/1 41.875” S40 Vertical Extrusion

3/3a 1/1 41.875” S40 Vertical Extrusion

4/4a 1/1 42” S40 Vertical Extrusion

5/5a 1/1 42” S40 Vertical Extrusion

6 1 41.75” S40 Vertical Extrusion

7 1 42” S40 Vertical Extrusion

8a/8b 1/1 41.906” Z45 Horizontal Extrusion

9a/9ba 1/1 41.906” Z45 Horizontal Extrusion

10/10a 1/1 36” Z45 Horizontal Extrusion

11/11a 1/1 22” Z45 Horizontal Extrusion

12a/12b 1/1 30” Z45 Horizontal Extrusion

13a/13b 1/1 30” Z45 Horizontal Extrusion

Attach graphics

to velcro on back of

assembled backwall

10a

11a

S40

12a

12b

13a

13b

Velcro

PR37

Extrusion

Profile

Slide PR37 extrusion into

groove of vertical and tighten

set screw to secure in place.

Extrusion

Profile

Extrusion

Profile

Z45

Velcro

BACK VIEW

FRONT VIEW

Velcro

www.classicexhibits.com

Step 2

Page 2 of 9

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - Counter Assembly

Steps

1) Attach horizontal extrusions [15] between vertical

extrusions [4 & 14] and [5 & 14a] inserting infills as shown.

2) Attach door to hinges as shown in detail.

3) Velcro shelf support to inside of pedestal, then set

internal shelf on top of supports.

4) Place counter top on assembled pedestal.

5) Attach plex shelf to countertop with

standoffs as shown in detail.

Door

Insert Insert

14a

Counter Top

Plex

Shelf

Internal Shelf

Door

Hinge

Door Attachment

Slide pin into

hinge attached

to vertical.

Slide door

hinge atop pin.

Extrusion

w/Door Hinges

Item Qty Description

14/14a 1/1 38” Vertical Extrusion

15 4 12.5” Horizontal Extrusion

16 2 Curved Extrusion

Attach standoff barrels to counter

and secure in place. Secure upper

shelf to standoffs using screw caps.

Plex Shelf to Counter Attachment

Upper Shelf -

Clear Plex

Threaded hole

in counter top

Standoff

Barrel

Screw

Cap

www.classicexhibits.com

Step 3

Page 3 of 9

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - Attachments Assembly

Steps

1) Connect canopy pieces together using bolts and wing nuts provided, see Example of Canopy Connection detail.

2) Connect header extrusions [18a,18b,19a,19b,20a,20b] together as shown.

3) Attach header & canopy to assembled backwall as shown in detail.

4) Attach wings using A10 clamps as shown.

5) Attach round graphic signs to backwall with standoffs as shown in detail.

6) Attach iPad clamshells to backwall as shown in detail.

7) Attach literatrure rack as shown in Literature Rack Attachment detail.

Secure with

wing nut

Connect 3 piece Canopy

together by using bolts and

wing nuts provided.

Bolts

Connecting

Canopy Pieces

Together

Example of Canopy Connection

18a

18b

19a

19b

20a

20b

18a 18b

19a

19b

20a

20b

Bolt

Wing Nut

Header Attachment

Attach connector piece to rack

as shown. Then connect

assembled literature

rack to vertical extrusion.

Literature Rack Attachment

Tighten Lock

to Secure

Item Qty Description

18a/18b 2/2 39” Vertical Extrusion

19a/19b 2/2 5.862” Horizontal Extrusion

20a/20b 2/2 38.5” Curved Extrusion

Slide A10 Clamp

into groove

of square extrusion.

When desired location

is found, tighten

set screw to secure.

Set-

Screw

A10

Tighten black plastic

set screw to secure

Wing in place.

Black Plastic

Set-screw

Wing Attachment

Graphic

Cap

Standoff

Barrel

Slide connector on back of standoff

barrels into groove of extrusion and

twist to secure in place. Secure graphic

to standoffs using screw caps.

Graphic Attachment

Tighten Lock

to Secure

Swivel

Mounting

Plate

iPad Mount Attachment

Attach connector piece to iPad

mount as shown. Then connect

assembled iPad mount to vertical

extrusion.

Attaching Graphics

Attach Header Graphic to Back of

assembled header frames.

www.classicexhibits.com

Step 4

Page 4 of 9

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX -

Door

Hinge

Door Attachment

Slide pin into

hinge attached

to vertical.

Slide door

hinge atop pin.

Steps

1) Attach lower horizontal extrusions [5,6,7] between

vertical extrusions [1,2,3,4] as shown.

2) Hang assembled door on hinges on vertical [1] as shown. Refer to detail.

3) Place side and front inserts between verticals as shown.

4) Attach upper horizontal extrusions [5,6a,7] between

vertical extrusions [1,2,3,4] and on top of infills as shown.

5) Velcro shelf support to inside of pedestal, then set internal

shelf on top of supports.

6) Place counter top on assembled pedestal.

Item Qty. Description

1 1 38“ Vertical Extrusion w/ Door Hinges

2 1 38” Vertical Extrusion w/ Door Stop

3 1 38“ Vertical Extrusion

4 1 38” Vertical Extrusion

5 2 22.0197“ Horizontal Extrusion

6/6a 2/2 12.5” Horizontal Extrusion

7 2 25.639“ Curved Extrusion

Door

Insert

4a 3

Counter Top

Internal Shelf

Extrusion

w/Door

Hinges

Shelf

Supports

Pedestal Assembly

www.classicexhibits.com

Step 5

Page 5 of 9

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - Packing Case 1

Graphics

Setup Hardware

Top View of Each Level

Level 3 Level 5Level 4

Level 2

Level 1

Ceiling

Pieces

Wings

Ceiling

Piece

16 (x2)

11,11a

Header

Frame

12a,13a

12b,13b

Round

Sign

www.classicexhibits.com

Step 6

Page 6 of 9

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX - Packing Case 2

Level 3

Curved

Door

Infills

Top View of Each Level

Level 1 Level 2

Internal Shelf

Counter Top

14 14a

15(x4)

www.classicexhibits.com

Step 7

Page 7 of 9

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX -

Internal Shelf

Counter Top

Infill

Pedestal Side

Assembly

25(x2)

Level 3

Top View of Each Level

Level 1 Level 2 Level 4 Level 5

Flat Door

Pedestal Side

Assembly

Shelf Supports

27(x2)

24a,23a

Packing Case 3

www.classicexhibits.com

Step 8

Page 8 of 9

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX -

Graphics

Setup Hardware

Top View of Each Level

Level 3 Level 4Level 2

Level 1

Ceiling

Pieces

Header

Frame

8a,8b

9a,9b

10,10a Additional Parts for 10x20

Wings

Round

Sign

Packing Case 4

www.classicexhibits.com

Step 9

Page 9 of 9

866.652.2100

WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL

SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Order #XXXXX -

Top View of each Level

Level 1 Level 2 Level 3

Wing Panels

Base Plate #28

Round Sign

#31

#32

#31

#29

#30

Packing Case 5

Classic Exhibits VK-2920 Setup Instructions

Classic Exhibits VK-2920 Setup Instructions

Classic Exhibits VK-2920 Setup Instructions

Related papers

Other documents