Classic Exhibits VK-1319 Setup Instructions
- Type
- Setup Instructions
www.classicexhibits.com
Step 1
Page 1 of 5
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Layout
Perspective View
Plan View
10’
10’
www.classicexhibits.com
Step 2
Page 2 of 5
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C E liateDD liateDDetail B
Detail A
Setscrews
www.classicexhibits.com
Step 1
Page 1 of 5
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Backwall Assembly
Steps:
1) Attach lower
vertical extrusions [2,3 & 9] to base plates [1].
2) Attach upper verticals [4 & 5] to lower verticals [2 & 3] as shown.
3) Attach horizontal extrusions [6a & 6b], [7a & 7b] & [8a & 8b] together
as shown.
4) Connect horizontal assemblies [6a/6b] [7a/7b] & [8a/8b] between
vertical assemblies as shown.
5) Connect horizontal extrusions [10] between verticals [2,3 & 9] as shown.
When
assembled
Item Qty Description
1 2 Base Plate
2 1 48” S80 Vertical Extrusion
3 1 48” S80 Vertical Extrusion
4 1 45.6711” Curved Vertical Extrusion
5 1 45.6711” Curved Vertical Extrusion
6a/6b 1/1 36.062” Z45 Horizontal Extrusion
7a/7b 1/1 44.6482” Z45 Horizontal Extrusion
8a/8b 1/1 47.3183” Z45 Horizontal Extrusion
9 2 38.6145” Curved Vertical Extrusion
10 2 11.75“ Z45 Horizontal Extrusion
2
9
9
10
10
6a
6b
7a
7b
8a
8b
3
4
5
1
Attach graphics
to velcro on front of
assembled backwall
Velcro
Velcro:
Front/Top Edge
Velcro:
Front/Top Edge
1
Velcro
www.classicexhibits.com
Step 2
Page 2 of 5
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Backwall Attachments
Steps:
1) Attach lights to top of backwall as shown
.
2) Attach graphic header to velcro on front of [8a & 8b] as shown.
3) Attach wings to A-10 clamps on sides as shown.
4) Place counter tops on top of extrusions [9 & 10] as shown.
5) Attach monitor mount to backwall as shown.
When desired location
is found, tighten
set screw to secure.
Tighten knob to secure
wing/shelf in place.
Slide connector on back
of A10 clamp into groove
of extrusion.
A10 Clamp Attachment
Wing
Counter Top
Counter Top
Wing
Graphic Header
Wing
Wing
Monitor Mount Attachment
Connectors
Attach monitor mount back
plate to connectors using
setscrews provided.
www.classicexhibits.com
Step 3
Page 3 of 5
866.652.2100
© 2013
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
- Pedestal Assembly
Front Aluminum portion of Pedestal Assembly
3) Attach Verticals [2 & 3] to Base Plate [1].
NOTE: Base Plate Centered and Flush with Back LT Portion of Pedestal.
4) Attach horizontals [4,5 & 6] between Verticals [2 & 3] as shown.
5) Place counter top on top of assembled pedestal as shown.
6) Attach graphic sign to Velcro on horizontal [6].
LT Pedestal Assembly
1) Assemble panels together starting with 1 in numerical order.
2) Attach Internal Shelf with provided shelf supports.
Panel Description
1 5.75”r X 38”h Quarter Curve Panel
2 19”w x 38”h Flat Panel
3 5.75”r X 38”h Quarter Curve Panel
4 5.75”r X 38”h Quarter Curve Panel
5 19”w x 38”h Flat Panel w/Door
6 5.75”r X 38”h Quarter Curve Panel
Item Description
1 Custom Base Plate
2 38”h Curved Round Vertical - Counter Support - Left side
3 38”h Curved Round Vertical - Counter Support - Right side
4 7” Lower Tapered Horizontal extrusion
5 8” Middle Tapered Horizontal extrusion
6 16.5” Upper Tapered Horizontal extrusion
Color Coded Clip
w/ assembly number
is top of panel
Panel Lock
When Required
Black Clip
is bottom of
panel
Connector
Cut Away View Of
Slide Clips
Slide Panel
down until
clips lock.
Left Hand
Grasps Panel
Firmly
With Right Hand Thumb
Close to Seam
Squeeze
Push Forward &
Lift
1
2
3
4
6
5
4
4
3
1
2
5
6
Steps 1 & 2 - LT Details:
Internal Shelf
Counter Top
Graphic Sign
-
1
-
2
-
3
-
4
-
5
Classic Exhibits VK-1319 Setup Instructions
- Type
- Setup Instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- polski: Classic Exhibits VK-1319
Related papers
-
Classic Exhibits VK-2916 Setup Instructions
-
-
-
-
-
-
-
-
-