Classic Exhibits VK-2954 Custom Exhibit Setup Instructions
- Type
- Setup Instructions
www.classicexhibits.com
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - 10x20 - General Layout
Plan View
20’
10’
Perspective View
Perspective View
www.classicexhibits.com
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
www.classicexhibits.com
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - SEG Installation Instructions
SEG Graphic Installation
1) Locate channels along the edges of extrusions
2) Insert graphic corners first into channels then center
point of graphic into channels. Allows for proportional
fit around the perimeter of the extrusion.
3) Working from center to corner, slide silicon edge
on graphic into channel.
4) After all edges of graphic have been inserted into
channels, step back and assess graphic fit, make
adjustments where needed.
LT Panel Assembly
1) With a vertical offset, place LT-Panels side-by-side;
slide vertically offset panel down to lock panels
together and in place.
2) Corner Connectors (90°, T-Connector, Straight Connector)
connect just as panels connect together. Repeat Step 1
for installing corner connectors to panels.
LT Panel Disassembly
1) To disassemble push panel with upper locks horizontally
to disengage top lock clip.
2) Slide panels or connectors vertically in opposing directions
to release latches and disconnect parts.
While pushed in,
pull panel up to
disassemble
Push Panel in to
disengage the lock.
Fold edges over.
Insert into
groove
of frame
www.classicexhibits.com
Step 1
Page 1 of 4
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Backwall Assembly
Plan View
Plan View
Door
Two Locks - Lock
at bottom and lock
at top (Typ.)
When assembled
Steps:
1) Connect panels together using custom cam
locks as shown. Refer to detail.
2) Join panel [A & B] toghter with vertical narrow
wood panel usings bolts and wing nuts.
Door
A
A
B
B
C
C
D
D
E
E
F
F
G
G
H
I
I
HJ
J
K
K
SEG
Extrusion
Profile
TSP7
Place hex tool in hole on side of panel and rotate
to activate lock and attach panels together.
*Custom Cam Lock Attachment
Hex Key Tool
Hole Lock
Step#1 Step#2
Lock
Hex Key Tool
*
*
*
*
*
*
*
*
***
*
*
*
** *
*
*
*
*
*
*
*
*
*
*
**** See attached SEG graphic
installation for graphic attachment
Bolt & Nut
Connection
*
www.classicexhibits.com
Step 2
Page 2 of 4
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Backwall Attachments
When assembled
Steps:
1) Connect ceiling pieces together using bolts and wing nuts. Refer to detail.
2) Attach assembled ceiling atop assembled wall panels using bolts as shown.
3) Attach header to assembled wall panels with metal plates using bolts.
4) Attach monitor mount to backwall as shown. Refer to detail.
Header
Bolt & Nut
Connection
*
*
*
*
*
*
Header
Ceiling
Ceiling
Plate
Bolts
Attach wall plate to
panel with bolts and
standoffs
Panel
Attach monitor brackets
to back of monitor.
Hang brackets
from wall plate
0
0
0
0
Monitor Mount Attachment
*
www.classicexhibits.com
Step 3
Page 3 of 4
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Planter Box Assembly and Placement
Plan View
Plan View
When assembled
When assembled
Steps:
1) Remove cap and
connect to wood sections together using
studs and wing nuts. Refer to detail.
2) Rest assembled planter box against assembled backwall.
3) Place flower pots inside assembled planter box as shown above.
*
*
*
*
**
*
Connect to wood
sections using studs and
wing nuts as shown.
Wing nuts Studs
Cap
Cap
Flower
Pots
www.classicexhibits.com
Step 4
Page 4 of 4
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Reception Counter
When assembled
Plan View
Plan View
Front View
Lights
Graphic
(velcro attachment)
Rear View
Steps:
1) Connect two piece reception counter together
using bolts. Refer to detail.
2) Place flower pots atop assembled
reception counter.
3) Velcro attach graphic to front of reception counter.
Flower
Pots
*
Bolt into
threaded Hole
Connection
*
*
-
1
-
2
-
3
-
4
-
5
-
6
-
7
Classic Exhibits VK-2954 Custom Exhibit Setup Instructions
- Type
- Setup Instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Classic Exhibits VK-2920 Setup Instructions
-
-
-
-
-
-
-
-
-
