Classic Exhibits VK-2964 Setup Instructions
- Type
- Setup Instructions
www.classicexhibits.com
Step 1
Page 1 of 4
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2964 - General Layout
Plan View
Perspective View
10’
20’
www.classicexhibits.com
Step 2
Page 2 of 4
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C E liateDD liateDDetail B
Detail A
Setscrews
www.classicexhibits.com
Step 1
Page 1 of 4
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2964 Backwall Assembly
1A
1A
1A
1A
7
10
10a
11
6
4
5
9
8
2
3
7a
6a
4a
5a
9a
8a
2a
3a
Item
1A
2/2a
3/3a
4/4a
5/5a
6/6a
7/7a
8/8a
9/9a
10/10a
11
Qty.
4
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1
Description
Base Plates
39” Vertical extrusion
39” Vertical extrusion top left outside cut
39” Vertical extrusion
39” Vertical extrusion top right outside cut
41” Horizontal extrusion
41” Horizontal extrusion
41” Top left curved extrusion
41” Top right curved extrusion
28” Horizontal extrusion
28” Horizontal extrusion
Steps:
1) Attach base plates [1A] to lower verticals [2,2a,4 & 4a].
2) Connect upper verticals [3,3a,5 & 5a] with
connection bars [b] to lower verticals.
3) Connect horizontals [6 & 7] [6a & 7a] with connection bar [a].
4) Connect horizontals [10,10a & 11] between verticals.
5) Connect curved extrusions [8 & 9] [8a & 9a] with connectors [a].
6) Connect curved assemblies [8/9] [8a/9a] between verticals.
7) Attach Velcro Graphic to back of frame as shown.
Velcro:
Back/Top
Edge
Velcro:
Back/Top
Edge
Velcro:
Back/Top
Edge
Velcro:
Back/inside
Edge
Back View
Back View
Back View
Attach graphic
to velcro on back of
assembled frame
Turn Knob Clockwise
to Tighten Lock
indicates location of
knobs on BACKSIDE of unit.
Do not over tighten Knobs
Knob
Knob
indicates
location of connection
lock with knob.
Horizontal Placement
Stopper
Set upper horizontal
bar atop stopper where
indicated on verticals
Note: Slide connection
bar between extrusions and
tighten knobs to secure.
Connection Bar
b
a
b
b
b
a
a
a
Velcro:
Back/Top
Edge
Velcro:
Back/Top
Edge
Velcro:
Back/Top
Edge
Velcro:
Back/inside
Edge
Velcro:
Back/inside
Edge
Velcro:
Back/inside
Edge
www.classicexhibits.com
Step 2
Page 2 of 4
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2964 Backwall Attachments
Wing
Wing
Wing
Wing
Steps:
1) Attach Wings to A10’s as shown in Example of A10 Clamp Attachment detail.
2) Attach header graphic as shown in Graphic Attachment detail.
3) Connect lights as shown in Light Connection detail.
4) Connect monitors as shown in Monitor Mount Attachment details.
Light Connection
Attach light to
backwall where
desired and tighten
in place.
Graphic
Cap
Standoff
Barrel
Slide connector on back of standoff
barrels into groove of extrusion
and twist to secure in place. Secure graphic
to standoffs using screw caps.
Graphic Attachment
Header
Header
When desired location
is found, tighten
set screw to secure.
Slide connector on back
of A10 clamp into groove
of extrusion.
Example of A10 Clamp Attachment
Tighten knob to secure
shelf/wing in place.
Monitor Mount Attachment
Connectors
Attach monitor mount back
plate to connectors using
setscrews provided.
*
*
*
*
*
*
*
*
*
*
*
*
**
*
*
*
*
*
*
Attach wall plate to
horizontal bar using
bolts and wing nuts
Hook monitor brackets over
top of wall plate, then secure
with safety bolts to bottom
of monitor brackets.
Monitor Mount Attachment
www.classicexhibits.com
Step 3
Page 3 of 4
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-2964 Backwall Counter Assembly
12
13
15
14
When assembled
Counter Top Attachment
Insert screws located
on underside of counter
into holes on flange plate
and secure with wing nuts.
Wing Nut
12
14
13
12
15
15
14
13
12
15
14
13
Item
12
13
14
15
Qty.
4
4
4
4
Description
11.5” Horizontal Extrusion
26.75” Curved Extrusion
20.3” Curved Extrusion
Hostess shelves
Steps:
1) Attach Curved extrusions [13,14].
2) Attach horizontal extrusion [12] to [13/14].
3) Connect [12/13/14] to vertical extrusion as shown.
4) Attach hostess shelves [15] between backwall vertical
and curved vertical [13].
5) Screw in top plate to curved extrusion [13] as shown.
6) Connect counter top as shown in detail below.
7) Attach monitor mounts as shown in detail.
Note: Curved extrusion
[13] and horizontal [14]
stay assembled for
shipping and packing.
Counter
Counter
Counter
Counter
www.classicexhibits.com
Step 4
Page 4 of 4
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Pedestal QTY X 2
Counter
Infill
Hinge
Infill
Infill
6
3
2
4
10
9
12
11
5
1
8
7Back Side
When assembled
Front Side
When assembled
Item
1-2
3-4
5
6-7
8
9
10-11
12
Qty.
1ea.
1ea.
1
1ea.
1
1
1ea.
1
Description
38” Vertical Extrusion w/ cut
38” Vertical Extrusion
18.9” Horizontal Extrusion
18” Horizontal Extrusion
20” Horizontal Extrusion
22.5” Curved Extrusion
18” Horizontal Extrusion
20” Horizontal Extrusion
Steps:
1) Attach lower horzontals [5,6,7,8] between
verticals [1,2,3,4] as shown.
2) Attach door using pins as shown in
Door Attachment detail.
3) Insert infills as shown.
4) Insert [9,10,11,12] between verticals.
5) Place internal shelf on top of shelf supports.
6) Place counter on top.
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge atop pin.
Hinge
Door
Shelf Supports
Shelf Supports
Shelf Supports
Shelf Supports
www.classicexhibits.com
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Packing
Counter
14
12
12
13
13
8
9
4523Base Plate
Wings
& Header
Base Plate
6 7
14
Counter
www.classicexhibits.com
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Counter
7,6,10,11
Shelf Supports
Infills
Shelf
Door Assembly Door Assembly
Case 2
Level 1 (Bottom Layer) Level 2 Level 3 Level 4 Level 5
Graphics
Lights
Setup Hardware
Packing
www.classicexhibits.com
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Case 3
Level 1 (Bottom Layer) Level 2 Level 3 Level 4 Level 5
Counter
14
12
12
13
13
8
9
4523Base Plate
Wings
& Header
Base Plate
6 7
14
Counter
Packing
www.classicexhibits.com
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Counter
7,6,10,11
Shelf Supports
Infills
Shelf
Door Assembly Door Assembly
Case 4
Level 1 (Bottom Layer) Level 2 Level 3 Level 4 Level 5
Graphics
Lights
Setup Hardware
Packing
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Classic Exhibits VK-2964 Setup Instructions
- Type
- Setup Instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- polski: Classic Exhibits VK-2964
Related papers
-
Classic Exhibits VK-1120 Setup Instructions
-
-
-
-
-
-
-
-
-