Anova STXTG9648SM Installation guide

Brand: Anova

Model: STXTG9648SM

Type: Installation guide

This manual is also suitable for

Installation Instructions

TOOLS NEEDED: HARDWARE NEEDED:

Step -by-Step Installation Sequence

Some products may require assembly before or during installation; please consult the assembly instructions if applicable.

Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a 3,000 psi minimum

and be cured for at least 28 days prior to the installation of the bench.

CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.

800.231.1327

[email protected]om

1. Place the stanchion in the desired location. Mark

the location of the holes with a pencil. To verify the

alignment of your anchor markings, reference the

foot mount sheet at the back of these instructions.

Surface Mounted Tree Guard Systems

Mason Drill Bit Set

Hammer Drill

Safety Glasses

Pencil

Wire Brush

LevelHammer

SS or Rubber Washers

90107A127 OR 90130A050

OPTIONAL

3/8" x 5" 18-8

Stainless Steel Stud Anchors

92188A203

5/8” Wrench/

Socket Set

Installation Instructions

Surface Mounted Tree Guard Systems

2. It is recommended that you start holes in

sequential order from the smaller to the larger drill

bits to avoid oversized holes or holes drilled too

deep. Begin with 1/4” diameter drill bit followed by

the 5/8” diameter bit.

3. Evacuate debris from the mounting holes using

compressed air and a steel wire brush.

4. Locate an anchor and adjust the nut so it is ush to

the top of the anchor to protect the threads from

being damaged, and insert into the hole.

5. Use the hammer to x the anchor into the drilled

hole by giving it several hammer blows.

6. Repeat steps 2-5 until all anchors are installed.

7. Remove the nut from the anchor and align the

mounting holes of the stanchion over the top of

the anchors and slide down into place.

8. Care should be taken to avoid rubbing the powder

coating o the stanchion. Mount the stanchion

to the anchor using fasteners (A) and washers (B).

Leave hardware nger tight until all panels have

been mounted.

9. Verify the stanchion is level and aligned properly

before installing the panels.

Assembly Instructions

Component parts:

Hardware Needed:

Assembly:

800.231.1327

[email protected]om

1. Inspect the shipping container contents for damaged or missing components.

2. Lay all parts on a soft work surface or on the shipping packaging to prevent damage to nish.

NOTE: Before assembly, it is recommended that a light oil or petroleum jelly be applied to screw threads.

Tools Needed:

• 9/16” Wrench or Socket

• 7/16” Wrench or Socket

Surface Mounted Tree Guard Systems

1/4"-20 Stainless Steel

Cap Nut(s)

5/16" Stainless Steel

Flat Washer

Stanchion(s)

5" Stainless Steel

Stud Anchor

Panel(s)

1/4"-20 Stainless Steel

Carriage Bolt(s)

Surface Mounted Tree Guard Systems

3. Once the stanchions are secured to the ground,

locate two carriage bolts, two washers, and two

cap nuts. Attach the panel to one stanchion by

using the carriage bolt rst through the top square

hole on either end of the panel, then through the

stanchion mounting bracket.

4. Secure the carriage bolt on the back side of the

bracket by inserting on a washer followed by a cap

nut.

5. Repeat this process on the top square hole on the

opposite end of the panel.

6. Repeat for all remaining mounting holes on the

panel.

Assembly Instructions

Replacement Parts

3 4

Stanchion

Panel

Installation Instructions

Surface Mounted Tree Guard Systems

• Furniture must not be used other than for its intended purpose and should be inspected regularly for loose, missing, or

broken hardware, and general instability

• Furniture that is damaged or appears to be unstable must be removed from service and repaired or replaced

• Repairs must be made using only factory authorized parts and methods.

WARNING

• Do not drag the assembled unit across any surface.

• This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to remove surface

dirt. Do not clean with a solvent or petroleum based products.

CARE AND

MAINTENANCE

Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.

FOOT MOUNT(S)

48.00

CENTER TO CENTER

52.00

6.00

4.00

.64 (4 PLCS)

PER POST

48.00

CENTER TO CENTER

52.00

6.00

4.00

.64 (4 PLCS)

PER POST

52.00

48.00

Anova STXTG9648SM Installation guide

Brand: Anova

Model: STXTG9648SM

Type: Installation guide

This manual is also suitable for

Download PDF

report

Anova STXTG9648SM Installation guide

This manual is also suitable for

Anova STXTG9648SM Installation guide

Related papers

Other documents