Hammer DrillHammer
Pencil
Wire Brush
Level
Safety Glasses
anovafurnishings.com
888.535.5005 tel
TOOLS NEEDED: HARDWARE NEEDED:
Installation Instructions
Step-by-Step Installation Sequence
!
Tandem Bike Racks, Surface Mount
Product ships fully assembled.
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a
3,000 psi minimum and be cured for at least 28 days prior to the installation of the bike rack.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
(6) SS or Rubber Washers
90107A127 OR 90130A050
(6) 3/8”-16 x 1” SS
Button Head Cap Screw
92949A624
(6) 3/8" Drop-in Anchors
97083A310
Allen Wrench Set
7/32"
Masonry Drill Bit Set
1/4" & 1/2"
3/8" Drop-in Anchor
Setting Tool
Unit Weight
Unit Shipping Wt. UPS
(1-2 Units)
Unit Shipping Wt. Truck
(3+ Units)
Unit Ship Size
w/Pallet
Max Units
Per Pallet
Pallet Size/Wt.
(48” X 32”)
Total No.
Pkgs.
Shipping
Class
35 lbs.
38 lbs./unit
38 lbs./unit
10 cu. ft.
8
50 lbs.
1
250
211 North Lindbergh Blvd.
St. Louis, MO 63141
800.231.1327 tel.| 314.754.0835 fax
specify@anovafurnishings.com
anovafurnishings.com
SHIPPING INFORMATION
8/20/2019Copyright 2019 ANOVA® Manufactured in the U.S.
CIRCLEBRS2— Tandem Stainless Steel Bike Rack, Surface Mount
Tandem stainless steel bike rack, surface mount
Material
The bike rack is 32.25” tall and made from 2.38” O.D. Schedule 10, 316L stainless steel pipe support sections.
316/316L stainless steel derives its advantage through an addition of at least 2% molybdenum. Molybdenum
provides increased resistance to corrosion including sea water and deicing salt environments. Bike rack will
accommodate up to two bikes, one on each side of the rack.
The bike rack is designed to be surface mounted. Each leg features a 7.75” x 5.5” plate with three .5”
diameter predrilled holes for surface mounting to prevent movement.
Surface mounting is required; mounting hardware is not included. Stainless steel hardware recommended
to prohibit rusting.
Finish
316/316L stainless steel is highly resistant to salt corrosion, rusting, pitting, and cracking. It remains clean and
rust-free without paint or alternative finish.
Color
See website or sales representative for color choices.
Assembly
The bike rack ships fully assembled and ready for use. Surface mounting may require some assembly.
Maintenance
Clean periodically, as conditions dictate. See ANOVA® stainless steel care guide at
http://www.anovafurnishings.com/sites/default/files/products/CIRCLEBRS2/resources/stainless-steel-
maintenance.pdf.
Warranty
20-year limited structural warranty from the date of purchase. See full details on multi-year warranties for
components at www.anovafurnishings.com/warranty.aspx.
5.50"
Ø 2.38"
7.75"
4.25"
4.00"
Ø .50"
FOOT MOUNT
10.77"
Manufactured in the U.S.
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
Installation Instructions
Step-by-Step Installation Sequence
1.
2.
3.
5.
4.
6.
7.
8.
Evacuate debris from mounting holes using compressed air and a steel wire
brush. This will create a clean environment for the anchor system.
Repeat steps 3 - 6 until all anchors are installed.
!
!
5
42
5
Copyright 2019 ANOVA®
09/19/2018
Care should be given to avoid rubbing the powder coating o the foot.
A 3/8" rubber washer is a suitable replacement option. Mount the bike rack
to the anchors by fastening a button head cap screw and washer into each
anchor. Leave the hardware nger tight until all of them have been installed.
Verify that the bike rack is level before tightening the anchors. Tighten all of
the hardware with a 7/32" Allen wrench.
Align the mounting holes of the bike rack over top of the anchors.
Use the 3/8" drop-in anchor setting tool and hammer to x the anchor into
the drilled hole by inserting the narrow end of the tool into the anchor and
giving it several hammer blows.
Insert one 3/8" drop-in anchor into the hole and use a hammer to tap the
anchor ush with the concrete.
It is recommended that you start holes in sequential order from the
smaller to the larger drill bits to avoid oversized holes or holes drilled too
deep. Begin with 1/4" diameter drill bit followed by the 1/2" diameter bit.
Place the bike rack in the desired location. Mark the location of the holes with
a pencil. To verify the alignment of the anchor markings you may reference
bottom of page 1.
Tandem Bike Racks, Surface Mount
7
8.1 8.2
/
