Cornelius Viper Cart Installation guide

Brand
Cornelius
Model
Viper Cart
Category
Multimedia carts & stands
Type
Installation guide

Cornelius Viper Cart

The Cornelius Viper Cart is a mobile cart designed to hold and support the Cornelius Viper unit, allowing for easy movement and positioning of the unit for service and cleaning. It is compatible with 2, 3, and 4-barrel Viper units.

The cart features four captive nuts on the bottom to accommodate 3/8-16 bolts, which are used to secure the Viper unit to the cart. The 2-barrel cart has movable wheels that act as outriggers to provide stability during movement.

To ensure stability, the cart is equipped with shims that can be added or removed to level the cart. The shims are placed between the caster and the support bracket.

Cornelius Viper Cart

The Cornelius Viper Cart is a mobile cart designed to hold and support the Cornelius Viper unit, allowing for easy movement and positioning of the unit for service and cleaning. It is compatible with 2, 3, and 4-barrel Viper units.

The cart features four captive nuts on the bottom to accommodate 3/8-16 bolts, which are used to secure the Viper unit to the cart. The 2-barrel cart has movable wheels that act as outriggers to provide stability during movement.

To ensure stability, the cart is equipped with shims that can be added or removed to level the cart. The shims are placed between the caster and the support bracket.

Viper Cart Installation Instructions
© 2009-2018, Cornelius Inc. - 1 - Publication Number: 620043075INS
INSTALLATION INSTRUCTIONS
Viper 2 Flavor, 3 Flavor and 4 Flavor Carts
S
AFETY INSTRUCTIONS
!
WARNING:
Before starting installation, read and understand all safety label and warnings on the machine. Also review and
understand all safety instructions in the owners, installation and service manuals.
Failure to comply could result in serious injury, death or damage to the equipment.
QUALIFIED SERVICE PERSONNEL
!
WARNING:
Only trained and certified electrical, plumbing and refrigeration technicians should service this unit.All wiring and
plumbing must conform to national and local codes.
Failure to comply could result in serious injury, death or equipment damage.
!
WARNING:
Disconnect power to the unit before servicing. Follow all lock out/tag out procedures established by the user. Verify all
power is off to the unit before performing any work.
Failure to comply could result in serious injury, death or damage to the equipment.
SAFETY PRECAUTIONS
This unit has been specifically designed to provide protection against personal injury. To ensure continued
protection observe the following:
!
CAUTION:
Always be sure to keep area around the unit clean and free of clutter.
Failure to keep this area clean may result in injury or equipment damage.
Kit Includes:
Table 1. Parts List
Item No. Part No. Description Qty.
1 620043075 Viper 2 Fl Cart 1
2 620053990 Viper 3 Fl Cart 1
3 620046556 Viper 4 Fl Cart 1
4 620045325 Shim - 2.50 OD X .625 ID X .075(2FL) 6
5 620045325 Shim- 2.50 OD X .625 ID X .075 (3FL and 4FL) 4
6 620066849 Cart Viper 2FL Red 1
7 620066850 Cart Viper 3FL Red 1
8 620066851 Cart Viper 4FL Red 1
Tools Required:
• ¾” Open-End Wrench
Revision Date: April 9, 2018 www.cornelius.com Revision: F
Viper Cart Installation Instructions
Publication Number: 620043075INS - 2 - © 2009-2018, Cornelius Inc.
CART INFORMATION AND MOUNTING
The Viper unit may be mounted on a mobile cart (Cornelius part no. 620043075 / 620066849[Red cart] for 2-barrel
unit, 620053990 / 620066850[Red cart] for 3-barrel unit and 620046556 / 620066851[Red cart] for 4-barrel unit)
which allows some movement of the unit for service and cleaning. There are four captive nuts on the bottom of the
Viper to accommodate four 3/8-16 bolts. These bolts must be installed to secure the unit to the cart.
2 FL carts are designed with movable wheels that act as outriggers to provide stability to the unit when it is being
moved.
!
WARNING:
The above listed mounting bolts must be installed and the wheels extended and locked in the outboard position
prior to moving the unit.
Failure to comply could result in serious injury, death or equipment damage.
Caster Installation:
Cart is supplied with three (3) shims under each front swivel caster. Six (6) additional shims are also supplied loose
in a plastic bag. In the case where the cart is not level, follow the instructions in the following table to install the
shims.
3- Flavor and 4- Flavor Carts are supplied with two (2) shim
s under each front swivel caster. Four (4) additional
shims are also supplied loose in a plastic bag.
Table 2. Installation Procedure
Step Action
1 Unpack the Kit
2
Turn the cart upside down and locate the holes
for th
e casters on the bottom of the cart.
Figure 1.
3
Using a ¾” open-end wrench, loosen the nut on
the bottom of the swivel caster.
Figure 2.
Viper Cart Installation Instructions
© 2009-2018, Cornelius Inc. - 3 - Publication Number: 620043075INS
!
WARNING:
Do not install anything except the shims between the caster and the support bracket. Doing so can create an
unsafe load on the caster stud resulting in damage that may cause the cart to tip.
4
Add or remove shims as required to level the
cart.
Figure 3.
5 Tighten the nut using the ¾” open-end wrench.
Figure 4.
6 Stand cart upright and inspect. If cart is not level, repeat steps 1 through 3 as necessary on the other casters.
Table 2. Installation Procedure
Viper Cart Installation Instructions
Publication Number: 620043075INS - 4 - © 2009-2018, Cornelius Inc.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Cornelius Viper Cart Installation guide

Brand
Cornelius
Model
Viper Cart
Category
Multimedia carts & stands
Type
Installation guide

Cornelius Viper Cart

The Cornelius Viper Cart is a mobile cart designed to hold and support the Cornelius Viper unit, allowing for easy movement and positioning of the unit for service and cleaning. It is compatible with 2, 3, and 4-barrel Viper units.

The cart features four captive nuts on the bottom to accommodate 3/8-16 bolts, which are used to secure the Viper unit to the cart. The 2-barrel cart has movable wheels that act as outriggers to provide stability during movement.

To ensure stability, the cart is equipped with shims that can be added or removed to level the cart. The shims are placed between the caster and the support bracket.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents