NextBase 612GW Owner's manual

Instruction Manual

INTRODUCTION TO USING A DASH CAM

The iN-CAR CAM range of Dash Cams have been designed specifically with ease of use in mind, it is

recommended NOT to change the default settings, which have been carefully selected to give the

best performance for day to day use.

Please check the firmware version of the Dash Cam, the version can be found in the set up menu

under System Info.

The latest versions are available to download from our website, where you can download and update

when necessary.

Basic operation:

It is essential that a quality branded U3 type micro SD card is used with this Dash Cam due to the

very large data rate generated by 4K recording.

The Dash Cam is set to record video, in files of just 1 minute in length. This means that each video file

is a manageable size should you need to download and send to your insurance company.

Eventually your MicroSD card will fill up with video files but don't worry, the camera automatically

deletes the oldest file to make space for new recordings. This way you never run out of space and

have plenty of driving historical evidence saved.

All Video files are recorded in BOTH High resolution and Low resolution simultaneously, with the Low

resolution file being ideal for watching on smaller portable devices via Wi-fi.

The Time and Date are automatically set upon the camera from satellite data, based on the Country

selected from within the first Time Use menu.

The Time and Date will also update automatically for Daylight Savings Time, again based on the

Country selected.

There are 3 modes of camera operation - Video, Photo and Playback.

Video Mode: The default mode when the camera is turned on, for video recording.

Photo Mode: Allows you to take still photographs.

Playback mode: Allows you to view recorded video or photographs upon the Dash Cam

LCD screen.

Press the MODE button on the Dash Cam to select required mode.

Automatic Start / Stop Technology. The Dash Cam senses power supplied to the cigarette lighter

socket as soon as the vehicle ignition is turned on and will start to record automatically.

When the ignition is turned off, the Dash Cam will perform an automatic shutdown process.

02

INTRODUCTION TO USING A DASH CAM (CONTD.)

1. Tips for capturing best video footage:

1.1 Position the Dash Cam in the centre of the windscreen and ideally behind the rear view

mirror so it is not a distraction to the driver.

1.2 Reduce the amount of sky in the picture, by angling the view of the camera towards the road.

Too much sky will make the road appear darker due to the automatic exposure compensation.

1.3 Remove unnecessary items from your dashboard. If objects are placed on your dashboard

these can cause reflections to be seen on the windscreen and these reflections may be

captured during recording.

1.4 To improve dash board glare, a Nextbase Reflection free lens can be purchased.

2. Tips for stable memory card performance:

2.1 Format your memory card using the Dash Cam. This will make sure that the card is structured

specifically for your camera. Press SETTINGS and choose the Format Card option on the first

page. Follow the on-screen instructions accordingly.

2.2 Switch off the Dash Cam before removing or inserting the SD memory card, to prevent the

chance of damage being caused to the memory card or the files stored upon it.

03

TABLE OF CONTENTS

INTRODUCTION TO USING A DASH CAM

TABLE OF CONTENTS

PRECAUTIONS

CAUTIONS ON USING THIS PRODUCT

FCC STATEMENT

PRODUCT SPECIFICATION

PACKAGE CONTENTS

PRODUCT FEATURES

POWERED GPS MOUNT

CAMERA - PARTS & CONTROLS

IN VEHICLE INSTALLATION

FIRST TIME USE

TOUCH SCREEN

VIDEO MODE

PHOTO MODE

PLAYBACK MODE

SETTINGS

PC CONNECTION

TV CONNECTION

Wi-Fi CONNECTION

TROUBLE SHOOTING

.........................................................................

......................................................................................................

................................................................................................................

..............................................................................

............................................................................................................

...............................................................................................

.....................................................................................................

..................................................................................................

......................................................................................

...............................................................................................

..............................................................................................................

...................................................................................................................

.................................................................................................................

...........................................................................................................

.......................................................................................................................

.............................................................................................................

.........................................................................................................

.......................................................................................................

02

04

05

06

09

10

11

12

17

21

22

23

26

27

30

41

43

44

04

PRECAUTIONS

CAUTION:

LCD:

WEEE:

Disposal of Waste Electrical and Electronic Equipment and/or Battery by users

in private households in the European Union.

This symbol on the product or on the packaging indicates that this cannot be disposed

of as household waste. You must dispose of your waste equipment and/or battery by

handing it over to the applicable take-back scheme for the recycling of electronic

equipment and/or batteries. For more information please contact your local household

waste disposal office.

A Liquid Crystal Display (LCD) screen is a multilayer complex component, containing

691,200 pixels. Pixels can however fail during normal product life. 1 pixel = 0.0001%

failure rate, and one pixel failure per year of operation is considered normal and not

a cause for concern.

To reduce the risk of electric shock, do not perform any servicing other than that

contained in the instruction manual unless you are qualified to do so.

Have the unit serviced by a qualified service technician if;

The Unit has been exposed to rain or water.

The unit does not seem to operate normally.

The unit exhibits a marked change in performance.

WARNING:

Do not expose this product to rain, moisture or water under any circumstances, doing

so may result in the risk of electric shock or fire.

Please read this manual carefully before operation and keep it for future reference. It will be helpful

should you encounter any operational problem.

1. Ensure that the windscreen is free of dirt or grease before placing mount upon it.

Do not obscure the view of the road ahead or impede the deployment of any airbags in the event 2.

of an accident.

When not in use, please disconnect the car adaptor from both the 12/24Vdc outlet in your vehicle 3.

and the device itself.

4. Only clean the device with a soft dry cloth, for tough dirt, apply some neutral detergent diluted in

5 to 6 parts water to a soft cloth.

Note that alcohol, thinner, benzene etc could cause damage to the paint or coatings.

Avoid making contact with the len as damage be caused. 5. s may

If required clean the glass lens carefully using spectacle lens cleaning fluid on a soft cloth only. 6.

The video recordings made by this are intended for personal use only. 7. Dash Cam

Publication of the recordings on Youtube, the internet or other methods are subject to the 8.

Data Protection Act and the requirements thereof must be adhered to.

If the is to be used within a commercial environment, i.e. truck use, then the CCTV Dash Cam

regulation apply also, in addition to the Data Protection Act regulations. This includes labeling to

identify the use f CCTV is taking place, the omission of Audio recording and informing the o

authorities of who controls the data.relevant

Video playback upon the device which is visible to the driver is prohibited or restricted in some 9.

countries or States. Please adhere to these laws.

Whilst driving, do not adjust the controls of your device as this is a distraction to driving. 10.

CAUTIONS ON USING THIS PRODUCT

Some Products may contain components that are small enough to be swallowed.

Please keep out of reach of children.

CHOKING

HAZARD:

05

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

• This appliance and its antenna must not be co-located or operated conjunction with any other

antenna or transmitter.

• A minimum separation distance of 20cm must be maintained between the antenna and the person

for this appliance to satisfy the RF exposure requirements.

FCC CAUTION:

Any changes or modifications to the equipment not expressly approved by the party responsible for

compliance could void your authority to operate the equipment.

06

SUPPLIER'S DECLARATION OF CONFORMITY

(47 CFR Section 2.906).

We; Tank Design

Hereby, Declare that the essential requirements set out in the 47 CFR Sections 2.906 of FCC, have

been fully fulfilled on our product with indication below:

1. Applicant's Info

Company Name: Portable Multimedia Ltd

Mailing Address : Unit 2, Caerphilly Business Park, Van Road, Caerphilly. CF83 3ED. UK

Contact : Graham Lambert

Tel : +44 02920 866429

Email Address : [email protected]

2. Product Info

Product Name : Dash Cam

Model No. : NBDVR612GW

Brand Name : Nextbase

3. Applied Standard

Standards

E-CFR Title 47 Part 15 Subpart B—Unintentional Radiators: 2017

Report No. WTS18S05112835E

4. Test Firm Used to Take Measurements:

Name : Waltek Services (Shenzhen) Co., Ltd.

Address : 1/F, Fukangtai Building, West Baima Rd Songgang Street, Baoan District,

Shenzhen, Guangdong, People's Republic of China, 518105

Contact Name : Philo Zhong

Tel : +86 755 8355 1033 802

Email : [email protected]

Designation No. : CN1201

FRN : 0027148261

FCC - STATEMENTSUPPLIER'S DECLARATION OF CONFORMITY

07

FCC - STATEMENTSUPPLIER'S DECLARATION OF CONFORMITY

SUPPLIER'S DECLARATION OF CONFORMITY CONTINUED

5. FCC Marking

6. Responsibilities and obligations

Strictly follow the FCC rules of 2.906, 2.908, 2.909.

7. Applicant's Authorization

Company Name: Portable Multimedia Ltd

Mailing Address : Unit 2, Caerphilly Business Park, Van Road, Caerphilly. CF83 3ED. UK

Contact Person : Graham Lambert

Signature:

Email Address : [email protected]

Tel : +44 02920 866429

Date : 14th June 2018

8. Responsible party in US.

Company Name: Tank Design

Mailing Address: 158 Sidney Street, Cambridge, MA 02139, United States

Contact Person : Mr Scott Watts

Signature:

Email Address : [email protected]

Tel : (617) 388-8380

Date : 14th June 2018

08

Model Number / Name

Power Requirements

Power Supply

Sensor Resolution

Lens -

Type / Angle / Aperture

Recording Resolution

Screen Type

Screen Size

Screen Resolution

Screen Ratio

Card Reader

SD Card

(Recommended Type)

SD Card Recorded file

Capacity

(based on default settings)

Recording Format

Video / Audio Out

Internal Battery

Unit Dimensions

Unit Weight

NBDVR612GW / ELITE

5V / 1.5A

12-24Vdc Car Power Cable (supplied)

Fuse Type: 20mm / 1.5A

Output: 5Vdc

8.57M Pixel

7G / 150° / F1.6

3840 x 2160 @ 30fps & 768 x 432 @ 30fps (default)

Touch (Capacitive)

3.0"

960 (W) X 240 (H) pixels x RGB

16:9

64-128GB MicroSD Card

use a 64-128GB MicroSD Card, U3 type, for best results

recognized brand

Please note, a U3 MicroSD Card is required for 4K recording

64GB MicroSD = 200 minutes of recording

128GB MicroSD = 400 minutes of recording

MP4

High Definition: Type C Socket (Video / Audio)

Lithium-ion 3.7V / 260mAh (approx. 15mins recording time)

Battery design allows the 'Auto Power Off' feature to function in

event of power loss within the vehicle. It is not intended as an

alternative power source to replace the supplied car adaptor.

97 x 59 x 42mm

151g

PRODUCT SPECIFICATION

Android is a trademark of Google Inc. in the United States and other countries.

Mac is a registered trademark of Apple Inc. in the United States and other countries.

iOS is a trademark or registered trademark of Cisco in the United States and other countries.

Windows is a registered trademark of Microsoft Corporation in the United States and other countries.

Exmor R is a trademark of Sony Corporation.

NEXTBASE Replay 3™ is a registered trademark of Portable Multimedia LTD in the United Kingdom.

NEXTBASE Cam Viewer™ is a registered trademark of Portable Multimedia LTD in the United Kingdom.

microSD™ and the microSD logo are trademarks of SD-3C, LLC.

Wi-Fi® is a registered mark of Wi-Fi Alliance Corporation.

Other trademarks and trade names are those of their respective owners.

09

PACKAGE CONTENTS

Dash Cam

Powered GPS Mount Car Power Cable USB Cable

PRODUCT FEATURES

Quick Start

Guide

Please check the contents of your NEXTBASE product.

Product appearance may differ slightly to that shown above.

Window

Sticker

Thank you for purchasing this NEXTBASE Dash Cam, in this section we will outline some of the

features available with this Dash Cam.

3.0" LCD Colour Touch Screen

LCD touch screen for ease of use and viewing the playback of recorded videos and photos.

Powered GPS Mount

Supplied with an Easy-fit powered mount, which allows the Dash Cam to be fitted and removed

quickly and easily. The car power cable can remain in place, connected to the mount.

GPS Logger

GPS co-ordinates and also time and date are recorded. The journey can then be viewed using the

supplied NEXTBASE Replay 3™ Windows & Mac playback software.

The software is also available to download from www.nextbase.com

Wi-Fi Connectivity

Connect your smartphone or tablet device to the Dash Cam wirelessly. Use your smartphone to

Start/Stop recording or to view or download files from the Dash Cam.

G Sensor / File Protection

In the event of an impact, a separate additional 30 seconds of protected recording will be saved

within the 'Protected' folder on the memory card.

This 30 second recording contains the 10 seconds prior to the protection taking place and the

following 20 seconds thereafter.

Intelligent Parking Mode

The Dash Cam will power on automatically and record 30 seconds of video, when physical movement

of your vehicle is detected.

Polarising filter

This Dash Cam incorporates a polarising filter to reduce windscreen glare and reflection.

Auto Dimming

Once enabled, the screen will automatically dim during night-time driving.

(adhesive mount included)

10

POWERED GPS MOUNT

Please see below to identify the parts of the supplied powered mount.

1. Locking lever

The locking lever is used to attach and release the window mount to your vehicles windscreen.

Pull the lever down to prepare the window mount for use. Once the mount is firmly upon the

windscreen (in a suitable location) push the lever to lock the mount in place.

2. Locking ring

Loosen the locking ring to adjust the Dash Cam position if required, remembering to

re-tighten before use.

3. DC-IN socket

Connect the supplied car power cable here.

4. Suction cup

This is used to attach and release the window mount to your vehicles windscreen.

Affix to a clear piece of windscreen where there is no paint effect applied.

5. Suction release tab

Once the locking lever has been opened use this release tab to break the seal between

the mount and windscreen.

4

5

1

3

2

11

CAMERA - PARTS & CONTROLS

Please see below to identify the parts and controls of your Dash Cam.

Front:

1. Mounting point (located under the dust cover)

After removing the dust cover, attach the supplied powered GPS mount here.

2. Speaker

Integral speaker for audio playback directly from the Dash Cam.

3. Polarising filter

This Dash Cam incorporates a polarising filter to reduce windscreen glare and reflection,

often seen on recordings.

In bright sunlight the filter will also enhance the colour and contrast levels to help capture

important number plate detail.

The filter has a rotating bezel, so you can adjust the polarising filter exactly how you need in

your vehicle.

To set the polarising filter, place a piece of paper on your dashboard below the rear view

mirror, but away from the windscreen. With the camera turned ON, you will see the reflection

of the paper in the LCD screen of the Dash Cam. Rotate the front ring of the polarising filter to

reduce reflection to the lowest possible level. This dramatically improves the recorded image

quality.

Note:

- Do not place fingers on the glass lens of the filter.

- Do not adjust the filter whilst in control of the vehicle.

1

3

2

12

CAMERA - PARTS & CONTROLS (CONTD.)

Back:

4. Red Power / Recording LED

This red LED will be lit when the Dash Cam is turned ON. During recording the LED will

flash.

5. Blue Battery LED

This blue LED will be lit when the internal battery is charging, once fully charged the LED will

go out.

Note:

- This Dash Cam uses Negative Temperature Coefficient (NTC) technology to protect

the battery. This will shut down battery charging should the Dash Cam’s internal

temperature exceed 70degrees.

This can happen during normal use and is not a cause for concern.

When the NTC is active the on screen battery icon will be seen as:

Charging will resume once the Dash Cam has returned to an acceptable internal

temperature.

6. Touch Screen

The 3'' touch screen makes the operation of the Dash Cam very easy, simply touch the

screen to open the main menu. It is from the main menu that the various modes

and settings of the Dash Cam can be accessed.

6

4

5

ᵒC

13

CAMERA - PARTS & CONTROLS (CONTD.)

Top:

7. Power On / Off

Press and hold for 2 seconds to turn on / off the Dash Cam.

8. DC-IN & USB socket (located under the dust cover)

Connect the supplied car power cable or USB data cable here.

Note:

- Normally the car power cable is connected to the mount when in use, not directly to

this socket.

7 8

14

CAMERA - PARTS & CONTROLS (CONTD.)

Bottom:

9. Light sensor

Detects the ambient light level and will adjust the screen brightness accordingly. Turned on

and off within the Settings Menu.

10. Reset button

In the unlikely event the Dash Cam becomes unresponsive, press the RESET button to

restart the Dash Cam.

17140001

9

10

Made in China

15

CAMERA - PARTS & CONTROLS (CONTD.)

Sides:

11. Protect button

Press whilst recording to protect the current file in event of an emergency situation.

If file protection is activated during recording by using the Protect button (or automatically by

the G Sensor), an additional 30 seconds protected recording will be saved within the ‘Protected’

folder on the memory card.

This 30 second recording contains the 10 seconds prior to the protection taking place

and the following 20 seconds thereafter.

Note:

- The original recording will also be saved to the memory card as usual.

12. HD Output (located under the dust cover)

Used to connect your Dash Cam to a television using an HD Cable (sold separately).

13. Microphone

Integral microphone for audio recording.

14. MicroSD Card slot

Insert the MicroSD card here, taking care that the gold contacts are facing towards the back

of the Dash Cam.

11

12

13

14

16

IN VEHICLE INSTALLATION

Please follow the instructions below for first-time installation of the Dash Cam. For day to day use

simply remove the camera from the mount as required.

1. Insert MicroSD Card

Insert a suitable U3 standard MicroSD in to the Dash Cam, taking care that the gold contacts

are facing towards the LCD screen side of the Dash Cam. Push the memory card until it clicks

into place.

Note:

- Use the edge of a small coin (or similar object) to push the memory card in place if required.

Take care that card has 'clicked' into place, a second push inwards will release the memory

card.

- Do not remove or insert the memory card when the Dash Cam is turned on. This may

damage the memory card.

2. Remove dust cover from Dash Cam

Remove the dust cover that is located on the top of the Dash Cam to gain access to the

mounting point.

To remove the dust cover, slide it forwards away from the LCD screen of the Dash Cam.

Note:

- If the Dash Cam is not to be used for a period of time please replace the dust cover to

help keep the metal contacts free of dust or other contaminants.

17

IN VEHICLE INSTALLATION (CONTD.)

3. Attach the mount to the Dash Cam

Slide the Dash Cam onto the mount. Once attached magnets within the mount will hold the

two parts together.

4. Attach the mount to the windscreen

Remove the protective plastic film from the suction cup of the mount.

Select a suitable position for the mount and clean the windscreen with a dry / clean cloth to

achieve a good contact between the glass and suction cup.

Release the locking lever of the mount by pulling down and then whilst holding the suction

cup onto the glass push the lever up to secure the mount to the windscreen.

To use the supplied adhesive mount, simply unscrew the locking ring and pull the mount apart.

Replace the sucker mount, remembering to tighten the locking ring securely.

Note:

- Choose a smooth glass area without painted effect.

- Please ensure that once mounted the Dash Cam will be located within the area of the

vehicles windscreen wipers to maintain a clear view during rainfall.

18

IN VEHICLE INSTALLATION (CONTD.)

The above diagram is for

illustration purposes only.

5. Connect car power cable

Route the supplied car power cable (as shown) and connect it to the DC-IN socket of the mount.

The Dash Cam will automatically power on and start recording once power is available.

In some vehicles this will be when connections are made, for others the Dash Cam will

power on once the ignition has been turned on.

If the vehicle in which the Dash Cam is installed has permanent live cigarette lighter sockets,

the user can simply use the power button to switch the Dash Cam off when the vehicle stops.

To take advantage of the Automatic Start / Stop Technology a Nextbase Hardwire Kit can be

installed on a switched-live power supply.

The Nextbase Hardwire Kit includes the necessary 12-24Vdc to 5Vdc convertor and battery

protection circuitry.

Should your vehicle not have a 12-24Vdc outlet, but does have a 5Vdc USB Outlet, this can be

used instead. Connect the USB cable supplied with your Dash Cam in place of the car power

cable.

You MUST however connect the USB cable to the mount, NOT directly to the Dash Cam

USB socket.

Note:

- Do NOT wire the Dash Cam directly to a 12V supply by cutting the cigarette plug

off the end of the cable, or damage will result.

12-24V DC

19

Please read and follow the notes below for the safe operation of your Dash Cam within your

vehicle.

As per the installation instructions, you must install the Dash Cam so it does NOT obstruct the

drivers view of the road, preferably on the passenger side of the vehicle and behind the rear view

mirror. Whilst the Dash Cam clearly needs to view through the windscreen in an area swept by the

windscreen wipers, the Dash Cam should be installed so as not to intrude significantly within the

wiped area. A 40mm intrusion into the green wiped area is the maximum permitted by law.

Do NOT mount the Dash Cam in front of the driver, as depicted by the red area in the above

illustration.

When installing the Dash Cam in a vehicle, always place the device securely against the

windscreen and where possible conceal the power cable under trim. Make sure that the Dash Cam

power cable does not interfere with the drivers operating controls, such as the steering wheel,

pedals or gear levers.

Do NOT mount the Dash Cam in front of an airbag field of deployment or in a position to obscure

any mirrors.

Clean the windscreen at the point of location, prior to fitting the Dash Cam, also, applying some

moisture to the suction cup may be beneficial, to ensure absolute adhesion.

It is recommended NOT to operate the Dash Cam whilst driving. The automatic Start-Stop

technology incorporated within the device negates any need to operate the controls whilst driving.

Adjust any settings or review recordings whilst stationery, not whilst driving.

Only use your mobile device whilst stationery, not whilst driving.

After the preliminary SETUP has been carried out upon the Dash Cam, adjust the Screen Saver

setting to On, this will blank the screen automatically shortly after starting the vehicle and

therefore the screen will NOT be a distraction in any way to the driver.

IN VEHICLE INSTALLATION (CONTD.)

20

Page is loading ...

NextBase 612GW Owner's manual

This manual is also suitable for

NextBase 612GW Owner's manual

Related papers

Other documents