QMS Magicolor 330 EX Quick Setup Manual

Category
Laser/LED printers
Type
Quick Setup Manual














1 20" (50.8 cm)
2 6" (15.2 cm)
3 22" (55.9 cm)
4 33" (83.8 cm)
5 53.4" (135.5 cm)
6 20" (50.8 cm)
7 22" (55.9 cm)
8 19.3" (49.0 cm)
9 22" (55.9 cm)
10 6" (15.2 cm)
11 27.2" (69.1 cm)
12 33" (83.8 cm)
Remove:
Outer carton
and packing
material
Consumables/
accessories kit

1
Lift off the
protective plastic
covering and any
instruction sheets.
Have four people
lift the printer
from its pallet.
»Note:
The
back of the
printer is
heavier than
the front.
2
Remove any tape
on the outside of
the printer.
Open the front
cover.
Remove the tape
holding the fuser
unit.
Close the front
cover.
 
1
Hold the metal
spring leaf loop
close to the tray.
Fit the right
coupling arm (but
not the spring
leaf) into the
printer hole.
Fit the left
coupling arm into
its hole.
2
Fit the right
coupling arm into
its right slot.
Fit the left
coupling arm into
its slot and press
downward until it
latches.
!
1
Slide the fuser
unit on the left
side out as far as it
will go.
Caution:
Pull the
fuser unit
only by
the hand-
hold.
2
Remove the two
metal fuser roller
separators and
the foam spacer
labeled “A” and
any tape attached
to the fuser unit.
Unpack the fuser
oil roller.
3
Remove the fuser
oil roller cover and
two pins.
»Note:
The
label on the
fuser oil roller
aligns with
the one on the
fuser unit.
4
Lower the fuser oil
roller into place
until it clicks.
Slide the fuser unit
into the printer.
"
1
Open the front
cover.
Pull out and
remove the anti-
rotation foam
spacer and its
label “B”.
2
Press and release
the antirotation
switch upward to
unlock the
toner knob.
Turn the knob
clockwise.
Caution:
You must release the switch before turning the knob.
2dv

3dv.eps
1dv





WARNING!
The printer weighs about 150 lbs (68
kg). Don’t lift it by yourself.
ACHTUNG!
Der Drucker wiegt ca 68 kg; bitte
versuchen Sie niemals, das Gerät alleine
anzuheben oder zu tragen.
WARNING
! You must use the carrying grips to
avoid getting your fingers caught under the printer
when you set it down.
ACHTUNG!
Heben Sie den Drucker nur an den
Tragegriffen an, da Sie sonst thre Finger
einquetchen, wenn Sie das Gerät absetzen.
Caution
:
Do not attempt to lift the printer
by the right side.
»Note:
The bottom foam blocks remain attached to the pallet. Retain all packaging materials and spacers in
case you have to move the printer later.
»Note:
Interface cables aren’t included. If you need cables, contact your local vendor or a computer store.
94dv.eps
92dv.eps
5dv.eps
91dv.e
p
s
93dv.eps
95dv.eps
If any items are missing or
damaged, contact your local
shipping company or vendor.




A
 
      
Note:
Spring leaf
 
3 One at a time,
unpack each new
toner cartridge.
Rock the cartridge
7 or 8 times to
evenly distribute
the toner inside.
4 Hold a toner
cartridge with the
arrow on top.
Insert the
cartridge until
seated.
5 Rotate the toner
cartridge
clockwise until the
” mark is
aligned with Lock
position.
Repeat steps 2
through 5 to install
the remaining
toner cartridges.
Caution:
Be sure to rotate the cartridge all the way to the Lock mark.
Otherwise, toner spillage may result.
Caution:
If a toner cartridge doesn’t slide in easity, don’t force it. Check
that you’re installing the correct toner cartridge into the correct slot of
the same color.
!"#"
Caution:
An exposed OPC drum is sensitive to light. Avoid prolonged exposure to light—do not remove the protective cover until ready to install into the
printer. Never touch the surface (the blue part). If the drum is scratched or contaminated with oil from your hand, printing will be degraded.
1 Holding it by the
handle, remove
the new OPC
drum cartridge
from its
packaging.
Remove the
protective blanket.
2 Make sure the
large lever is
turned counter-
clockwise to place
the “” mark on
the cartridge to
Unlock .
3 Match the arrows
to align the
guide with the top
of printer rail.
Push the OPC
drum cartridge
carefully all the
way into the
printer until it
clicks.
4 Turn the levers to
Lock .
»Note:
Unless
the OPC drum
cartridge is
inserted all
the way, the
levers cannot
be turned.
Close the front
printer cover.
Caution:
If the guide on the OPC drum cartridge is not aligned with the top of the rail, the cartridge may be damaged.
""
1 Pull out the media
cassette.
Remove the
spacer labeled “C”
and the spacer on
the right.
Press down the
metal plate until it
latches.
2 Squeeze the
retainers to move
the media guides
all the way out.
3
Align the corners
of the media stack
and insert it face
down, covering
the lower-right
arrow embossed
on the metal plate.
»Note:
The
media should
fit under the
fluke and
between the
guides.
4
Caution:
Do not overfill the cassette. The media cassette holds
250 sheets of 20 lb (75 g/m2) paper.
Set both guide
clips.
»Note:
If the
guide clips are
pressed too
tightly against
the media, that
may cause a
media jam.
Push the media
cassette firmly into
the printer.
»Note:
Automatic paper size detection cannot be assured if the left guide clip is even slightly out of position. Slide the guide clip to the left edge of the cassette, then reposition it.
 $
1 Slowly pull the
right-side
multipurpose tray
unit out as far as it
will go.
Remove the
protective pads.
2 Untwist the
shipping tie-wrap
and remove it.
Press the
multipurpose tray
unit firmly into the
printer until it
clicks.
Caution:
Failure to remove this tie-wrap will damage the printer.
 
!
LOCKED
"
#$

C
$

31dv
"%"&
Refer to the
instructions in
chapter 3
(parallel) or
chapter 4
(Ethernet) of the
Getting Started
manual to connect
your printer to a
PC or network.
»Note:
In compliance with UL guidelines, “The appliance inlet
is considered to be the main disconnect device.”
Make sure the
power to the
printer is off when
you plug in the
power cord.
Plug the other end
of the cord into a
grounded, surge-
protected
electrical outlet.
Turn on the
printer.
»Note:
A
startup page
should print.
"
See the
Getting
Started
manual for
instructions on
installing a QMS
printer driver.
Use the online
help to configure
the driver for
printing.
See the
Reference
manual
for complete
instructions on
configuring the
printer through the
control panel
menus.
 '
Refer to one of the following:
Chapter 8, “Troubleshooting Printer Problems,” in the
QMS
magicolor
330 Print
System Operation
manual.
Appendix A, “QMS Customer Support,” in any QMS
magicolor
330 Print System
manual.
"
Operate the printer within a temperature range of 41° to 89.6° F (5° to 32° C) and a relative humidity range of 15% to 85%.
Install the printer on a hard, level surface capable of supporting about 150 lbs (68 kg).
The printer must be placed no more than 10% from horizontal.
Allow enough space around the printer to allow adequate ventilation and easy servicing.
Use a properly grounded AC outlet with a line voltage of 120 V or 220–240 V, ±10%.
Maximum electrical current required during operation is 11 amps for 120 V, and 6 amps for 220–240 V.
Recommended frequency is 60 Hz ±2 Hz for a 120 V system, and 50 Hz ±2 Hz for a 220–240 V system.
" (
QMS,
magicolor
, and the QMS logo are registered trademarks of QMS, Inc.
This document is Copyrighted © 1999 by QMS, Inc., One Magnum Pass, Mobile, AL 36618. All Rights Reserved. This document may not be copied in
whole or in part, nor transferred to any other media or language, without the express written permission of QMS, Inc.




%%&
!""#
$%#
&!'('
)*)+

Installation
Operator
Administration
Idle
Operator
UseOperator
Admin
Use Admin
Off, On
(Enter
Off, On
Control
password)
password)
(Enter
InternetVisit the QMS Warranty Registration page on
the Internet at http://www.qms.com/support/prodreg/
Mail—Fill out and send in the warranty card enclosed in
your shipment.
Telephone—In the US, call QMS at (334) 633-4500.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

QMS Magicolor 330 EX Quick Setup Manual

Category
Laser/LED printers
Type
Quick Setup Manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI