Classic Exhibits VK-1329 Setup Instructions

Type
Setup Instructions
© 2019
Order #XXXXX
Locked layer contains
placeholder marks.
Perspective View
Top View
10’
10’
Scale: 18
VK-1329 Supernova
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS
© 2019
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information
© 2019
Order #XXXXX
LT Panel Assembly
1) With a vertical offset, place LT-Panels side-by-side;
slide vertically offset panel down to lock panels
together and in place.
2) Corner Connectors (90°, T-Connector, Straight Connector)
connect just as panels connect together. Repeat Step 1
for installing corner connectors to panels.
LT Panel Disassembly
1) To disassemble push panel with upper locks horizontally
to disengage top lock clip.
2) Slide panels or connectors vertically in opposing directions
to release latches and disconnect parts.
While pushed in,
pull panel up to
disassemble
Push Panel in to
disengage the lock.
4
13
2
Fold edges over.
Insert into
groove
of frame
SEG Graphic Installation
1) Locate channels along the edges of extrusions
2) Insert graphic corners first into channels then center
point of graphic into channels. Allows for proportional
fit around the perimeter of the extrusion.
3) Working from center to corner, slide silicon edge
on graphic into channel.
4) After all edges of graphic have been inserted into
channels, step back and assess graphic fit, make
adjustments where needed.
SEG Installation & Panel Assembly
© 2019
Crate 1 of 1
Order #XXXXX Crate Packing
© 2019
Step 1 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
Completed Assembly
2
3
4
7
6
5
1
*
**
*
**
Steps:
1) Attach base plate [1] to horizontal [2], using bolt.
2) Assemble extrusions together, as shown.
See 60° Corner Connection detail.
3) Install SEG graphic to assembled frame.
See SEG Installation sheet for instruction.
*
TSRV2
Bracket
A1
Bracket
1) Insert TSRV2 and A1 brackets
into grooves of CEI110.
2) Slide connecting CEI110 over
exposed end of brackets.
3) Tighten all set screws to secure.
60° Corner Brackets
Item
1
2
3
4
5
6
7
Qty.
1
1
1
1
1
1
1
Description
Base Plate
70” CEI110 Horizontal Extrusion
70“ CEI110 Angled Extrusion
25” CEI110 Angled Extrusion
70“ CEI110 Angled Extrusion
25” CEI110 Angled Extrusion
70” CEI110 Horizontal Extrusion
FRONT VIEW
Backwall Assembly
© 2019
Step 2 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
Completed Assembly
Wing
Wing
35
Wing
*
*
*
*
*
*
Steps:
1) Attach clamps to angled extrusions [3] and [5] then
connect wings. See Clamp Attachment detail.
Clamp Attachment
*
Wing
2
3
1
4
1) Slide clamp into groove
of extrusion.
2) Tighten set screw to
secure clamp to extrusion.
3) Insert wing into clamp.
4) Tighten knob to secure
wing in place.
FRONT VIEW
Backwall Attachments
© 2019
Step 3 of 4
Order #XXXXX
Locked layer contains
placeholder marks.
Completed Assembly
BACK VIEW
8
Bolt
Bracket
Standoffs
Screw
Caps
Screw
Caps
9
*
Monitor
Mount
Steps:
1) Connect verticals [8] and [9] together.
2) Attach assembled verticals [8/9] to assembled workstation floor, using bolt.
3) Attach monitor mount to vertical [9]. See Monitor Mount detail.
4) Attach bracket to angled vertical [3], using screw caps.
5) Attach workstation to bracket, using standoffs and screw caps.
6) Attach monitor then route cord through conduit.
See Cord Management detail.
Item
8
9
Qty.
1
1
Description
40.5” Q914 Vertical Extrusion
30” Q914 Vertical Extrusion
Monitor Mount
V4 Connectors
*
Slide connectors into groove
of extrusion. Tighten set screws
to secure connectors in place.
Attach monitor mount back
plate to extrusion, using bolts.
Bolts
Monitor
Mount
Cord Management
Route cord through conduit.
Attach conduit by pinching
the opening and inserting
into the groove of extrusion.
pinch
Cord
PR63 Conduit
MOD-1542 Workstation Attachment
© 2019
Step 4 of 4
Order #XXXXX
Shelf Support
Completed Assembly
6
6
7
7
3
8
1
1
2
Door
2
3
3
4
4
5
5
*
Shelf Support
Pedestal Top
Shelf
Graphic
Item
1
2
3
4
5
6
7
8
Qty.
1
1
1
1
1
1
1
1
Description
38”h Corner Connector
19”w x 38”h Panel w/ Door
38”h Corner Connector
19”w x 38”h Panel
38”h Corner Connector
19”w x 38”h Panel
38”h Corner Connector
19”w x 38”h Panel
Steps:
1) Connect panels and connectors together in numerical order,
making sure the Velcro is facing inward.
2) Connect shelf supports to Velcro on panels.
3) Place shelf on shelf supports.
4) Attach graphic to panel [6]. See Graphic Attachment detail.
5) place pedestal top onto assembled pedestal.
Shelf Support
Shelf Support
Graphic
Screw
Cap
Screw
Cap
Standoff
Place screw cap into hole in panel
[6] then screw into standoff. Screw
graphic standoffs using screw cap.
Panel [6]
Graphic Attachment
**
**
MOD-1541 Pedestal Assembly
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Classic Exhibits VK-1329 Setup Instructions

Type
Setup Instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI