Classic Exhibits ECO-2094 Setup Instructions

Brand: Classic Exhibits

Model: ECO-2094

Type: Setup Instructions

Order #XXXXX

Locked layer contains

placeholder marks.

10’

20’ Plan View

ECO-2094 - 10’ x 20’ Display

If you would like to tell us about your experience with your setup instructions please email us at [email protected]

SETUP INSTRUCTIONS

Order #XXXXX

Locked layer contains

placeholder marks.

= 1 sq foot

Grid View

Order #XXXXX

DO NOT USE POWER TOOLS

ALL CONNECTIONS MUST

BE TIGHTLY SECURED

Part Identification - Numbering

Spline Connection Base Plate & Extrusion Connection

General Setup Instructions

- Read entire setup instruction manual prior to

unpacking parts and pieces.

- The setup instructions are created specifically

for this configuration.

- Setup instructions are laid out sequentially in

steps, including exploded views with detailed

explanation for assembly.

WARNING

Cleaning & Packing

- For Cleaning Metal, Plex, & Laminate Parts:

Use a MILD NON-ABRASIVE cleanser and

soft cloth/paper towel to clean all surfaces.

- Keep exhibit components away from heat

and prolonged sun exposure.

Heat and UV exposure will warp and

fade components.

- Retain all provided Packing Materials.

All provided packing materials are for

ease of repacking & component protection.

Disassembly

- For loss prevention, tighten all set screws

and locks during disassembly.

Hex Tool - Essential for Assembly

Extrusion & Lock Connection Engaged Lock

LADDERS OR LIFTS

MAY BE REQUIRED

General Information

Order #XXXXX

Using Your Setup Instructions

Cleaning and Packing Your Display

The Euro LT Hybrids Setup Instructions are created specifically for your configuration.

They are laid out sequentially in levels, including exploded views, and a logical series of detailed steps

to assemble the main structure and components. We encourage you to study the instructions before

attempting to assemble your exhibit.

Each page reminds you to tighten the setscrews after disassembling your exhibit to prevent loss of the

locks and setscrews (see below in RED). This is VERY IMPORTANT.

1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.

2) When cleaning laminate inserts, countertops, or panels use mild cleansers and a soft material

such as cotton.

3) Keep all display components away from extreme heat and long exposure to sunlight to avoid

warping and fading.

4) Retain all packing material. It will make re-packing much easier and will reduce the likelihood

of shipping damage.

Each component has 2 clips,

the lower clip is ALWAYS

black. The top clip is color

coded to distinguish which

level. The color coded clip

also contains the numbered

label.

Connector

Level 1 = Blue

Level 2 = Red

Level 3 = Green

Level 4 = Black

Panel Lock

When Required

Color Coded Clip

w/ assembly number

Black Clip

is bottom of

panel

Cut Away View of

Slide Clips

Components connect together

by aligning them and sliding

downward connecting clips

together.

Configurations are assembled

from left to right, usually

starting with #1 and following

the numbered sequence.

Example of Connection Top View of Panels with Locks

The first level of components contain

panel locks that are located at the top of

the panel for extra stability and seamless

connection. When disassembling panels

twist top connection slightly and lift right

panel upward.

Panel Lock

When Required

Color Coded Clip

w/ assembly number

is top of panel

Left Hand

Grasps Panel

Firmly

With Right Hand Thumb

Close to Seam

Squeeze,

Push Forward,

And Lift

General Setup Instructions for Extrusion System

The Tool Typical Connection Typical Connection (cont’d) Numbered Label

Most exhibits can be assembled

with the supplied Hex Key Tool.

Occasionally, a flat head screw-

driver may be required.

Most horizontal extrusion connections have a patented expandable

lock. This lock inserts into the groove of an opposing extrusion.

Tightening the lock with the Hex Key Tool expands the lock and

creates a strong positive connection.

Each extrusion contains a numbered

label which corresponds with setup

instructions. The label is located

within a groove of the extrusion

(when possible). With extrusion

components the labels contain

Black numbers unless otherwise

specified.

Detail A Detail B Detail C

Horizontal Inline Connection (remove only one setscrew) Base Plate Connection Vertical Connection

(remove only two setscrews)

Detail D Detail E

Setscrews

Remove only (1) setscrew when disassembling.

Replace setscrew in extrusion after assembling

it. Before packing, replace setscrew in extrusion

to avoid losing it.

Attach base plate to round or

square vertical extrusion using

the bolt provided. Be careful

not to strip the threads.

When vertical extrusions are

packed in portable cases rather

than crates or tubs, they must be

broken down into smaller sections

which then require assembly.

Remove only (2) setscrews when

disassembling. Replace setscrews

in extrusion after assembling it.

Before packing, replace setscrews

in extrusion to avoid losing them.

EuroLT Assembly

Order #XXXXX

1) Slide TWO-PIECE TS RV 2 L-bracket into

Interior Center Slot of extrusion so that two

set screws are inside groove.

Tighten two set screws to secure.

2) Slide two A1 L-Brackets into outer interior

grooves of upper and lower horizontals.

Tighten set screws to secure.

4) Slide exposed ends of installed brackets of

upper horizontal into open ends of verticals.

Tighten set screws to secure.

3) Slide vertical extrusion over exposed ends

of brackets in lower horizontal.

Tighten set screws to secure.

Corner Bracket Installation

CEI-152 Profile

TS RV 4

Bracket

Insert two-piece

bracket into the

interior center slot

of extrusion.

Slide V4 Connectors

into front & back

interior grooves.

Secure inserted half of

bracket & connectors

using set screws.

Slide connecting

extrusion over

exposed ends

of bracket &

connectors.

Completed

Assembly

Secure extrusion,

using remaining

set screws.

Set

Screws

Straight Bracket Installation

TS RV 2

Upper

Horizontal

Lower

Horizontal

Upper

Horizontal

Lower

Horizontal

TS RV 2

Insert L-Brackets into the

Interior Center Slot & outer

interior grooves of extrusion.

Slide verticals over

brackets of lower

horizontal, then slide

upper horizontal &

brackets into grooves

& center slots

of verticals.

12 Brackets Total:

(4) - TS RV 2

(8) - A1 L-Brackets

Completed

Assembly

Corner Connection

1) Slide TWO-PIECE TS RV 4 straight bracket into

Interior Center Slot of extrusion, so that two of the

set screws are inside groove. Tighten two set screws

to secure.

3) Slide connecting extrusion over exposed ends of

bracket & connectors. Tighten all remaining set screws

to secure extrusions.

2) Slide two V4 Connectors into outer interior grooves

of extrusion, so that one set screw is inside groove.

Tighten set screw.

Straight Connection

Disassembly

1) Loosen set screws on brackets and slide

extrusions off of brackets.

CEI-152 Frame Assembly

CEI152 Frame Assembly

Order #XXXXX

CEI-110 Profile

Straight Bracket Assembly

1) Slide TWO-PIECE TS RV 4 straight bracket into

Interior Center Slot of extrusion, so that two of the

set screws are inside groove. Tighten two set screws

to secure.

3) Slide connecting extrusion over exposed ends of

bracket & connector. Tighten all remaining set screws

to secure extrusions.

2) Slide one V4 Connector into outer interior groove

of extrusion, so that one set screw is inside groove.

Tighten set screw.

TS RV 4

Bracket

Insert two-piece

bracket into the

interior center slot

of extrusion.

Slide V4 Connector

into front interior

groove.

Secure inserted half of

bracket & connector

using set screws.

Slide connecting

extrusion over

exposed ends

of bracket &

connector.

Completed

Assembly

Secure extrusion,

using remaining

set screws.

Set

Screws

Straight Connection

Corner Connection

TS RV 2

Upper

Horizontal

Lower

Horizontal

Upper

Horizontal

Lower

Horizontal

TS RV 2

8 Brackets Total:

(4) - TS RV 2

(4) - A1 L-Brackets

Slide verticals over

brackets of lower

horizontal, then slide

upper horizontal &

brackets into grooves

& center slots

of verticals.

Completed

Assembly

Insert L-Brackets into the

Interior Center Slot & outer

interior grooves of extrusion.

Disassembly

1) Loosen set screws on brackets and slide

extrusions off of brackets.

1) Slide TWO-PIECE TS RV 2 L-bracket into

Interior Center Slot of extrusion so that two

set screws are inside groove.

Tighten two set screws to secure.

2) Slide one A1 L-Bracket into outer interior

grooves of upper and lower horizontals.

Tighten set screws to secure.

4) Slide exposed ends of installed brackets of

upper horizontal into open ends of verticals.

Tighten set screws to secure.

3) Slide vertical extrusion over exposed ends

of brackets in lower horizontal.

Tighten set screws to secure.

Corner Bracket Assembly

CEI-110 Frame Assembly

CEI110 Frame Assembly

Order #XXXXX

Graphic Removal

To remove the graphic

the frame, locate the fabric

pull tab. Gently pull up on the

tab to remove the fabric.

Step 1

Insert corner A. Turn edge of

graphic so silicon welt is

perpendicular to face of

graphic. Insert narrow side

of welt with fabric to outside

into the channel. Repeat for

other side of this corner.

Step 2

Repeat Step 1 for opposite

corner C, then insert corner

B, followed by corner D, to

complete the installation of

the corners.

Step 3

Once all corners are inserted,

press one silicon edge into

channel from corners and

work toward the center.

Make sure welt is fully inserted

into channel. Continue until

all sides are done. Smooth

out edges of graphic.

It is important to first insert

graphic into each alternate

corner then to the sides of

the frame. If this is not done,

graphic will not fit into the

frame correctly.

Corner A

Corner D

Corner B

Corner C

from

SEG Installation

Crate 1 of 1

Order #XXXXX

Locked layer contains

placeholder marks.

CRATE PACKING

Crate Packing

Step 1 of 6

Order #XXXXX

Locked layer contains

placeholder marks.

Item

Qty.

Description

96”h CEI152 Vertical Extrusion

56”w CEI152 Horizontal Extrusion

56”w Z140 Horizontal Extrusion

Base Plate

U-Channel

Steps:

Refer to the CEI152 Frame Assembly general information page.

1) Attach U-Channel to lower horizontal. See U-Channel Attachment detail.

2) Connect verticals [1,3] between horizontals [5,6] using corner connectors.

3) Attach horizontal [7] between verticals [1,3].

4) Connect Base Plates [8] to underside of horizontal [5].

5) Connect power cords to Supernova lights; place transformers

into U-channels.

ELEVATION VIEW

Transformers

U-Channel Attachment

Insert V2 connectors on

bottom of U-Channel

into top groove of

horizontal extrusion.

Tighten bolts on V2

to secure connection.

bolts

When assembled

Power

Female

Transformer

144W / 6 Amp / 24V

Lights Male

Light to Light Attachment

Maximum of 7 lights per chain / 11 lights per Transformer

Light to Transformer Attachment Hole for wire

management

FRONT VIEW

U-Channel

Backwall Assembly

Step 2 of 6

Order #XXXXX

Locked layer contains

placeholder marks.

Transformers

ELEVATION VIEW

Item

Qty.

Description

96”h CEI152 Vertical Extrusion

46”w CEI152 Horizontal Extrusion

8” x 22” Base Plate

U-Channel

When assembled

Steps:

Refer to the CEI152 Frame Assembly general information page.

1) Install U-Channel to horizontal [15]. See U-Channel Attachment detail.

2) Connect verticals [13,14] between horizontals [15,16].

3) Install Base Plate [17] to bottom of horizontal [15], using bolt & wing nut.

4) Connect power cords to Supernova lights as shown.

Hole for wire

management

U-Channel Attachment

Slide V4 connectors into

top groove of horizontal

extrusion. Tighten set-

screws to secure.

Use bolts to connect

U-Channel to

horizontal.

connector

bolts

set

screws

AS VIEWED FROM

INSIDE THE BOOTH

U-Channel

Power

Female

Transformer

144W / 6 Amp / 24V

Lights Male

Light to Light Attachment

Maximum of 7 lights per chain / 11 lights per Transformer

Light to Transformer Attachment

Backwall Assembly (cont’d)

Step 3 of 6

Order #XXXXX

Locked layer contains

placeholder marks.

Item

Qty.

Description

96”h CEI152 Vertical Extrusion

46”w CEI152 Horizontal Extrusion

8” x 22” Base Plate

U-Channel

When assembled

Steps:

Refer to the CEI152 Frame Assembly general information page.

1) Install U-Channel to horizontal [20]. See U-Channel Attachment detail.

2) Connect verticals [18,19] between horizontals [20,21].

3) Install Base Plate [22] to bottom of horizontal [20], using bolt & wing nut.

4) Connect power cords to Supernova lights as shown.

AS VIEWED FROM

INSIDE THE BOOTH

U-Channel Attachment

Slide V4 connectors into

top groove of horizontal

extrusion. Tighten set-

screws to secure.

Use bolts to connect

U-Channel to

horizontal.

connector

bolts

set

screws

U-Channel

Hole for wire

management

ELEVATION VIEW

Transformers

Power

Female

Transformer

144W / 6 Amp / 24V

Lights Male

Light to Light Attachment

Maximum of 7 lights per chain / 11 lights per Transformer

Light to Transformer Attachment

Backwall Assembly (cont’d)

Step 4 of 6

Order #XXXXX

Locked layer contains

placeholder marks.

Item

17,22

Qty.

1,1

Description

96”h RSG540 Vertical Extrusion

19.722”w Z41 curved Horizontal Extrusion

Base Plate

Infill Infill

Infill

When assembled

Steps:

1) Connect Infills between frame assemblies as shown, using

A10 clamps. See A10 Attachment detail.

2) Attach Base Plates [17,22] to bottom of verticals [9].

3) Assemble horizontals [10] between verticals [9,13] &

[9,18], inserting Infill.

1) Slide A10 connector

into groove of extrusion.

2) Tighten set screw to

secure A10 to extrusion.

3) Insert Infill into Clamp.

4) Tighten knob to secure

infill in place.

A10 Attachment

Wing

Backwall Assembly (cont’d)

Step 5 of 6

Order #XXXXX

Locked layer contains

placeholder marks.

Steps:

Refer to the SEG Installation general information page.

1) Apply SEG Graphics to lightbox frames.

2) Connect Monitor Mount to horizontal [7].

See Monitor Mount Attachment detail.

Monitor Mount

Gra

Note: Monitor mount installs over SEG graphic.

Bolts

Monitor Mount Attachment

Install Monitor Mount to

Stand-off Barrels using bolts.

Attach Stand-off Barrels to horizontal

extrusion using wing nuts.

Stand-Off

Barrels

Wing

nuts

Completed Assembly

Monitor

Mount

SEG Graphic

SEG Blocker

SEG Graphic

Backwall Attachments

Step 6 of 6

Order #XXXXX

Locked layer contains

placeholder marks.

Counter Top

When assembled

1.5” standoff

barrels

standoff

caps

standoff

caps

1.5” standoff

barrels

4.5” standoff

barrels

Transformer

hole for wire

management To

Power

Note:

No standoff

cap for

middle

barrel.

***

Slide V20 Connector on

Standoff Barrel into groove

of horizontal extrusion.

Then turn barrel clockwise

to tighten in place.

Standoff Barrel Attachment

TOP VIEW

CEI110

bolt &

wing nut

Lights

Backer

FRONT

Item

1/2

3/4

Qty.

1/1

Description

46”w CEI110 Horizontal Extrusion

30.5”h CEI110 Vertical Extrusion

Power

Female

Transformer

96W / 4 Amp / 24V

Lights Male

Light to Light Attachment

Maximum of 7 lights per chain / 7 lights per Transformer

Light to Transformer Attachment

Steps:

1) Connect horizontals [3,4] between verticals [1,2],

sliding backer panel between verticals.

See CEI-110 Corner Connection detail.

2) Attach left & right cabinets to frame assembly [1/2/3/4]

using bolts & wing nuts.

3) Install Counter Top to assembly using standoff barrels.

See Standoff Barrel Attachment detail.

4) Connect power cords to Supernova lights as shown.

5) Apply SEG graphic to frame.

Refer to the SEG Installation general information page.

standoff

barrel

Turn to

tighten

CEI-110 Corner Connection

*1) Insert TSRV2 and A1 Brackets

into milled groove of extrusion.

2) Slide connecting extrusion

over exposed end of brackets.

3) Use Set screws to secure

extrusions.

TSRV2

Bracket

(2 pieces)

Screws

ECO-42C Reception Counter

Classic Exhibits ECO-2094 Setup Instructions

Classic Exhibits ECO-2094 Setup Instructions

Classic Exhibits ECO-2094 Setup Instructions

Related papers

Other documents