BSS Audio FDS366T OMNIDRIVE User manual

FDS-366T OMNIDRIVE™

User Manual

Connect here first...

- 2 -

FDS-366T

IMPORTANT SAFETY INFORMATION

DO NOT REMOVE COVERS.

NO USER SERVICABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS EQUIPMENT MUST BE EARTHED.

IT SHOULD NOT BE NECESSARY TO REMOVE ANY PROTECTIVE

EARTH OR SIGNAL CABLE SHIELD CONNECTIONS TO PREVENT

GROUND LOOPS. ANY SUCH DISCONNECTIONS ARE OUTSIDE

THE RECOMMENDED PRACTISE OF BSS AUDIO AND WILL

RENDER ANY EMC OR SAFETY CERTIFICATION VOID.

This equipment has been tested and found to comply with the following European and International Standards

for Electromagnetic Compatibility and Electrical Safety:

Emmissions (EU): EN55013+A12+A13 (1990)

Generic Immunity (EU): EN50082-1 (1992)

Mains Harmonics (EU) EN61000-3-2 (1995)

Voltage Fluctuations (EU) EN61000-3-3 (1995)

Electrical Safety (EU): EN60065+A11 (1993)

Electrical Safety (USA): UL813/ETL (1996)

For continued compliance with international EMC legislation ensure that all input and output cables are wired

with the cable screen connected to Pin 1 of the XLR connectors.

The input XLR Pin 1 is connected to the chassis via a low value capacitor, providing high immunity from ground

loops whilst ensuring good EMC performance.

The FDS-366T Omnidrive was designed and developed by BSS Audio, Hertfordshire, UK.

In keeping with our policy of continued improvement, BSS Audio reserves the right to alter specifications

without prior notice.

REGULATORY INFORMATION

Software version 2.00

ZM10019 issue 4 CB/PW/DN/DP/JWK

- 3 -

FDS-366T

Contents

FDS-366T Omnidrive compact plus

1.0 Primary Checks ......................................................................................... 8

2.0 Installation ................................................................................................. 8

3.0 Warranty Information ............................................................................... 9

About the FDS-366T Omnidrive Compact Plus...............................10

4.0 Introduction ............................................................................................ 11

5.0 Features .................................................................................................... 12

What is DEQ? ................................................................................................. 16

6.0 Dynamic Equalisation .............................................................................. 16

Notes and Uses ..................................................................................................................17

7.0 Crossover Shapes and Frequencies .......................................................... 19

Thiele Crossover ................................................................................................................21

Crossover comparison chart ............................................................................................... 22

Phase Compensation .......................................................................................................... 23

Stereo 3-Way with mono sub-bass. ................................................................ 24

8.0 Typical Applications ................................................................................. 24

6-Way zoning distribution .............................................................................. 25

LCR cinema systems (3x2-way)....................................................................... 25

Triple Bi-amp (Stage monitors) ........................................................................ 25

Mono 6-way ................................................................................................... 26

Stereo 6-way (example) .................................................................................. 26

9.0 Front Panel ............................................................................................... 27

10.0 Rear panel .............................................................................................. 29

Using the FDS-366T Omnidrive Compact Plus ............................... 30

Voltage setting................................................................................................ 31

11.0 Connections - Mains Power .................................................................. 31

AC Power fusing ............................................................................................ 32

Connections - Audio...................................................................................... 33

Balanced wiring.................................................................................................................. 33

- 4 -

FDS-366T

Unbalanced wiring ............................................................................................................. 34

MIDI ................................................................................................................................... 35

RS232 Serial ....................................................................................................................... 35

RS485 Serial ....................................................................................................................... 35

Program Select Port.............................................................................................................36

12.0 Navigation.............................................................................................. 37

The Navipad ................................................................................................... 37

The Rotary Encoder ........................................................................................ 37

13.0 Default Screen ....................................................................................... 38

14.0 Quick Start Guide .................................................................................. 39

Keep relative delays while delaying a group ....................................................................... 44

Name a band .....................................................................................................................44

15.0 Quick Reference - How to ... ................................................................. 44

Use delays for driver alignment .......................................................................................... 44

Make a band full range ...................................................................................................... 45

Add EQ for Constant Directivity horns................................................................................ 45

Load custom logos ............................................................................................................. 45

Programming functions in depth .....................................................46

Recalling a Program ........................................................................................................... 47

16.0 Program Functions - Recall .................................................................... 47

Storing a Program ...............................................................................................................48

Program Functions - Store.............................................................................. 48

Store Lock .......................................................................................................................... 48

Program lock ...................................................................................................................... 49

Store Type .......................................................................................................................... 49

Delete Program ..................................................................................................................50

Card types .......................................................................................................................... 51

Compatible Cards .............................................................................................................. 51

Storage life ......................................................................................................................... 51

PC Card format ..................................................................................................................51

17.0 PC Card Usage ....................................................................................... 51

FDS-355 compatibility ....................................................................................................... 52

Computer compatibility...................................................................................................... 53

- 5 -

FDS-366T

18.0 Utilities .................................................................................................. 53

1. Configuration.................................................................................................................. 54

2. Stereo Link...................................................................................................................... 54

3. Sum Type........................................................................................................................ 54

5. Phase Comp ...................................................................................................................55

4. Xover Adjust ................................................................................................................... 55

6. Alignment Assistant ......................................................................................................... 56

Method .............................................................................................................................. 56

Microphone placement and connection .............................................................................. 56

Procedure........................................................................................................................... 57

Selecting bands to measure ................................................................................................. 57

Adjusting the stimulus level ................................................................................................. 58

Notes ................................................................................................................................. 58

7. Delay Corrn (Correction) ................................................................................................. 60

8. Temperature.................................................................................................................... 61

9. Limit units ....................................................................................................................... 61

10. Delay units ................................................................................................................... 61

11. Brightness ..................................................................................................................... 61

12. Contrast ........................................................................................................................ 61

14. Owner lock ..................................................................................................................62

13. Lock out ....................................................................................................................... 63

Setting up 'Owner' Locks .................................................................................................... 63

Storing Owner Programs ..................................................................................................... 64

Adding further locks...........................................................................................................64

15. OEM Lock ....................................................................................................................65

Storing OEM Programs ........................................................................................................ 66

Adding further locks...........................................................................................................66

OEM & Owner Locks .......................................................................................................... 67

Configuration parameter note.............................................................................................. 67

Lockable Utilities ................................................................................................................ 67

17. Serial Port ..................................................................................................................... 68

18. MIDI Mode ...................................................................................................................68

16. Input A/AES .................................................................................................................. 68

19. MIDI Channel ............................................................................................................... 69

20. MIDI Dump .................................................................................................................. 69

23. Delete Program ............................................................................................................. 70

21. Backup & Swap ............................................................................................................ 70

22. Store Gain Trims ............................................................................................................70

24. Format Card.................................................................................................................. 70

19.0 Input Channels ....................................................................................... 71

2. Delay ............................................................................................................................. 72

3. EQ Bypass ...................................................................................................................... 72

- 6 -

FDS-366T

4. Dynamic EQ ...................................................................................................................72

1. Gain ............................................................................................................................... 72

DEQ ................................................................................................................................... 73

Thr (Threshold) ................................................................................................................... 73

Ratio .................................................................................................................................. 73

Attack and Release ............................................................................................................. 74

Atk (Attack) ......................................................................................................................... 74

Rel (Release) ....................................................................................................................... 74

20.0 Output Channels .................................................................................... 75

1. Name ............................................................................................................................. 76

2. Source ............................................................................................................................ 76

3. Low Shape ..................................................................................................................... 77

Low Freq/Xover ..................................................................................................................77

4. High shape..................................................................................................................... 77

High Freq/Xover .................................................................................................................77

6. Band gain....................................................................................................................... 78

5. Phase ............................................................................................................................. 79

Polarity .............................................................................................................................. 79

7. Limiter ........................................................................................................................... 79

Over (Overshoot) ............................................................................................................... 79

Thr (Threshold)................................................................................................................... 79

Rel (Release) ...................................................................................................................... 79

Atk (Attack) ........................................................................................................................ 79

Delay ................................................................................................................................. 80

EQ Bypass....................................................................................................... 80

Delay link .......................................................................................................................... 80

DEQ................................................................................................................................... 81

Thr (Threshold)................................................................................................................... 81

Ratio .................................................................................................................................. 81

Attack and Release ............................................................................................................. 82

Atk (Attack) ........................................................................................................................ 82

Rel (Release) ...................................................................................................................... 82

Outputs - EQ .................................................................................................. 83

EQ shape ........................................................................................................................... 84

Frequency .......................................................................................................................... 85

Width ................................................................................................................................. 85

Cut/Boost ........................................................................................................................... 85

- 7 -

FDS-366T

Reference Section ........................................................................... 86

21.0 Serial Communications ......................................................................... 87

MIDI ................................................................................................................................... 87

MIDI with PC Control.......................................................................................................... 88

Synchronous Control .......................................................................................................... 88

RS232 ................................................................................................................................ 89

RS485 & Multidrop ............................................................................................................. 90

22.0 Troubleshooting ..................................................................................... 94

23.0 FDS-366T Omnidrive MIDI Implementation ....................................... 95

A.1 FDS-366T MIDI Implementation ............................................................ 95

24.0 Default Configuration Settings ............................................................... 96

25.0 Filter Allocations .................................................................................... 98

26.0 Specifications and Block Diagram ......................................................... 99

27.0 Block Diagram ..................................................................................... 101

28.0 User Notes ........................................................................................... 102

- 8 -

FDS-366T

As part of BSS' system of quality control, this product is carefully inspected

before packing to ensure flawless appearance.

After unpacking the unit, please inspect for any physical damage and retain the

shipping carton and ALL relevant packing materials for use should the unit

need returning.

In the event that damage has occurred, please notify your dealer immediately,

so that a written claim to cover the damages can be initiated.

Please fill in the warranty details on the form opposite for future reference.

1.0 Primary Checks

2.0 Installation

Fig 3.1 Unit

dimensions.

Fig 3.2 Rack

dimensions.

✓

Note all dimension in mm

- 9 -

FDS-366T

When sold to an end user by BSS Audio or a BSS Audio Authorised Reseller,

this unit is warranted by the seller to the purchaser against defects in

workmanship and the materials used in its manufacture for a period of one

year from the date of sale.

Faults arising from misuse, unauthorised modifications or accidents are not

covered under this warranty. No other warranty is expressed or implied.

If the unit is faulty it should be sent to the seller of the equipment, in its original

packaging with shipping prepaid. The unit will be returned to you when the

repair has been completed. If the unit was purchased in the European Union,

you may, as an alternative, return the unit to any other BSS distributor in the

European Union.

You should include a statement listing the faults found. The unit’s serial

number must be quoted in all correspondence relating to a claim.

We recommend that you record your purchase information here for future

reference.

Unit Serial Number:

Dealer Name:

Dealer Address:

Post/Zip Code:

Dealer Phone Number:

Dealer Contact Name:

Invoice/Receipt Number:

Date of Purchase:

Comments or questions regarding the FDS-366T or other BSS products? Contact

us at this address:

BSS Audio

Cranborne House

Cranborne Road

Potter Bar

Herfordshire

EN6 3JN

England

Phone (+44) (0)1707 660667. Fax (+44) (0)1707 660742.

Web site, www.bss.co.uk

3.0 Warranty Information

IMPORTANT

✆

+

✍

- 10 -

FDS-366T

About the

FDS-366T

Omnidrive

Compact

Plus

- 11 -

FDS-366T

4.0 Introduction

Introducing the BSS Audio FDS-366T Omndrive Compact Plus, an incredibly

powerful loudspeaker management system in only 1U of rackspace! Based on

BSS Audio's many years of experience building analogue processing devices

for the live sound and installed markets, the FDS-366T Omnidrive is an 'all in

one' solution for system crossover assignment, EQ, delay and dynamics

control.

Processing power

Using custom designed digital signal processing (DSP) technologies BSS Audio

are able to deliver far more capabilities in one box than was realisable from a

whole rack of analogue equipment only a few years ago. Also as all the

processing on the audio signal is kept in the digital domain added noise and

phase anomalies usually expected with analogue equivalents are virtually

eliminated. The signals are processed at 24bit, 96kHz resolution to achieve a

dynamic range greater than 112dB to ensure the best possible audio quality for

your system.

Security

Moreover, the comprehensive security features included in the FDS-366T

enable the unit to be set up with varying degrees of access to its functionality

applied and protected by passwords. Indeed the whole unit can be locked

totally to prevent tampering, in installed applications for example.

Routing

An arrangement of 3 inputs and 6 outputs and an additional internal sum of

inputs A&B, A+B+C, pre or post input EQ can be matrixed in various

combinations to provide a complete loudspeaker management system with

integral crossovers, delays, dynamic EQ, and protection limiters.

Applications

The flexibility of the FDS-366T enables it to be employed for many system

uses, such as complete 3 way stereo setups or a 2 way LCR combination.

Equally FDS-366T Omnidrives can be stacked to run larger 5 and 6 way

systems and more.

In stage monitor systems the FDS-366T can function as a triple bi-amp

crossover with delay, limiters and EQ. On-stage 'hotspots' caused by monitors

with identical signals can be eliminated by applying small delays between

wedges.

Furthermore, the FDS-366T can function as a distribution unit to multizone

systems where crossovers may be passive or local to the loudspeaker. In this

case, the provision of delays and EQ can radically enhance such a system

while reducing both processing costs and required rack space.

Upgradeable operating system

The system operating software is held in flash EPROM, which means that

upgrading to new software is easy - either via PC card or from a PC via the

MIDI or RS-232 ports.

Memorising Setups

60 internal program locations are available to the user for storing system

setups, which may be generic system programs or complete venue settings.

These memories may be stored onto a PC card for backup or archiving.

- 12 -

FDS-366T

✓Individual keys to select input and output channels for editing.

✓Crossover slopes of 6,12, 18, 24 or 48dB per octave.

Filter types:Butterworth, Bessel, Linkwitz-Riley and WHISEWORKS-

NTM*.

✓Comprehensive output limiters on each band (mid-filter).

✓Equalisers and 'dynamic' equalisers on each input and output.

✓High resolution input and output delays up to 2.6 seconds in

approximately 11 microsecond steps.

✓Input LED metering, showing signals from -12dB to clip level, and SIG.

✓Output LED metering, showing signals from -20dB to +6dB over limit

threshold, and SIG.

✓Front panel output level trims and mutes.

✓Polarity reverse on each output.

✓Phase adjustment for each crossover point, and phase compensation

defeat.

✓PC card port for storage and recall of program settings

✓Electronically balanced inputs and outputs with transformer output

option.

✓MIDI, RS-232, RS-485 and program change ports on rear panel.

✓96kHz sample rate and 24bit encoding/decoding for audio excellence.

✓AES/EBU digital input for direct digital feeds into Omnidrive.

✓Alignment Assistant for setting up cabinet driver alignments.

✓Comprehensive system security with control lock out, programmable

'Owner' and 'OEM' locks, and 'Safe' mode available for complete

system lock out.

✓Temperature based delay correction.

5.0 Features

If you are familiar with the FDS-355 Omnidrive then look at the extra benefits

that the FDS-366T brings, an extra output channel, dynamic equalisation,

Thiele crossover shape and 96kHz audio quality to start with!

* The words "WHISEWORKS", "Neville Thiele Method" and NTM logotype are

trademarks of Precision Audio Pty. Ltd (registration pending). Manufactured

under license from Precision Audio Pty. Ltd. International Patents Pending.

- 13 -

FDS-366T

Features

Some of the features are explained in greater detail here.

• 96kHz Sample rate

The FDS-366T operates the A-D and D-A converters and the Digital

Signal Processing (DSP) at a sample rate of 96kHz. The use of a higher

Nyquist frequency enables the audio bandwidth to extend all the way

up to 40kHz. With this extra frequency response we have also been

able to incorporate more accurate filter sets for a more natural, open

sound.

There is also benefit from the improved filter response shapes when the

nyquist frequency (the maximum frequency of which the DSP can

correctly process the signal), moves up from 24kHz to 48kHz. Low-pass

filters and bell filters then retain their magnitude and phase response

shapes more accurately.

• AES/EBU digital input

The FDS-366T is equipped as standard with a stereo AES/EBU digital

audio input which will accept sample rates of 44.1, 48, 88.2 and 96kHz.

44.1 and 48kHz modes are sample-rate converted and the waveform

interpolated to 88.2 and 96kHz respectively within the FDS-366T so

that all of the filtering is done at the higher rate to get more of the

benefits of the increased sample rate. Using the AES input the

realisable dynamic range is increased to greater than 117dB.

• Phase matching

This feature maintains the inter-band phase relationship true to the

crossover type selected (Bessel, Butterworth, L-R etc), regardless of any

interference from far-end crossover filtering.

In 2-way crossovers, this is not an issue since each band has just one

high-pass or low-pass filter. Three or more bands however, cause at least

one band to have both low-pass and high-pass filters which react with

one another, so disturbing the correct phase relationship at the crossover

point. This can result in poor combining of adjacent crossover bands,

resulting in an irregular frequency response and non-uniform polar

characteristics.

The Phase Matching technique used in the FDS-366T eliminates this

problem by compensating for these phase anomalies. The phase

compensation can be bypassed if not required.

- 14 -

FDS-366T

Features

• Alignment Assistant

The Alignment Assistant is an advanced loudspeaker measurement

function built-in to the FDS-366T for directly measuring the delay and

phase relationships between drivers (using a measurement microphone),

and automatically adjusting the settings to accommodate these.

The Alignment Assistant has the ability to ‘see’ past the crossover filters,

and is thus able to compensate for the drivers and enclosures

themselves, leaving the crossovers to do exactly what they were

intended to do - presenting a precisely aligned acoustic wavefront.

The Alignment Assistant can measure and compensate for:

- Physical alignment of drivers within an enclosure.

- Driver or enclosure phase anomalies near the crossover point.

- Relative distance correction of arrayed boxes.

• Advanced Limiters

Driver protection limiters have always been a balance between

protection, transparency and the preservation of maximum power. The

all-new limiter algorithm in the FDS-366T not only allows the user the

freedom to change the way the compromises are balanced, but

introduces several new features which enable the requirements to be

met with less sacrifice.

- Feed-forward design for better stability.

- Adaptive attack, so that attack time is reduced the further over

threshold the signal strays. This helps to preserve transparency for

light overshoots, but acts more aggressively if the signal strays too

far.

- Adaptive release, so that short-term overshoots do not reduce the

average power output, whilst keeping distortion low on sustained

over-threshold signals.

- Adjustable attack speed (fast/med/slow/dual) - but still related to

the high-pass crossover frequency.

- Adjustable release speed (fast/med/slow) - but still related to the

high-pass crossover frequency.

- Brickwall overshoot limiter. This is actually a soft-clipper which

constrains signals which overshoot during the attack phase. The

user has adjustable ‘overshoot’ from 1 to 12dB (and off).

- Dual time-constant mode for giving simultaneous protection

against short-term mechanical damage or clipping, and longer

term thermal damage.

@

- 15 -

FDS-366T

•Safe mode

The FDS-366T has a hidden function called 'Safe'. 'Safe' mode is intended to

be used as a complete lock-out for installations or as the ultimate protection

for hire systems etc.

When SAFE mode is switched on, all controls are disabled, the screen blanks

and the backlight is dimmed. The input and output meters will still display the

existence of signal being processed through the unit but no one can change

any values within the unit.

! Any adjustments made to the gain controls whilst in 'Safe' mode will not be

heard until 'Safe' is turned off.

! As the 'Safe' mode is intended for ultimate security, the details of its use

cannot be published here. Please consult your dealer for further information

on Safe mode.

Features

- 16 -

FDS-366T

6.0 Typical Applications

The FDS-366T has three inputs: A, B, C. An internal mono sum of inputs is also

available for routing to any of the outputs. Many combination of routing inputs

to outputs is available, and the FDS-366T can be configured as a stereo or

mono device. The basic configurations are selected in the Utilities and the

following examples are based upon these as possible likely setups.

Systems can be run in one of two stereo 3-way modes.

LLMMHH allows compatability with the 355, now having two low outputs.

LMHLMH set up is an alternative, allowing users to choose the setup they are

most familiar with.

Stereo Link "On" mode allows the same parameters on the left and right

channels to be adjusted simultaneously, and any edits made whilst unlinked

preserve the left/right difference as an offset.

Note: The stereo pairs change appropriately for LLMMHH and LMHLMH

modes.

Stereo 3-Way with

mono sub-bass.

j

- 17 -

FDS-366T

The FDS-366T can be also be used as a zone distribution system, without

using any of its crossover facilities. Using this mode, a common input signal

can be routed to up to 6 separate outputs, each with delays, EQ and limiters.

Typical uses for this mode would include feeding a number of under-balcony

loudspeakers with integral passive crossovers, using the delays of the FDS-

366T for time correction, and EQ for tuning response.

For this application set the configuration to Mono and each output should be

full range (unless you particularly want to band restrict the outputs). Use the

'Xover Freq' screens in the output channel to set each band edge to be 'OUT'.

6-Way zoning

distribution

LCR cinema

systems (3x2-way) A similar configuration to the triple 2-way setup above.

The FDS-366T can provide 3 channels of bi-amp crossover for monitor racks

with EQ, delays, and limiters. With so much EQ available in the FDS-366T, it

is easy to assign 12 bands of EQ to the input, as well as EQ to the output

bands, saving the need for external EQ.

In LHLHLH mode by default, input A feeds outputs 1 and 2, input B feeds

outputs 3 and 4, and input C feeds outputs 5 and 6.

In this mode, it is possible to remove ‘hot spots’ on stage. Where the same mix

is sent to a number of performers, interaction between wedges can create lobes

of high intensity sound causing confusion. Using a fine delay to shift wedge

feeds can move these 'hot-spots' to less sensitive areas on stage.

Triple Bi-amp

(Stage monitors)

Typical Applications j

- 18 -

FDS-366T

In the mono mode, the FDS-366T can provide a full 6-way system. It can also

function as a 5-way system fed from input A, with an independent sub-bass

output fed from the sum of inputs A & B or input C.

Two FDS-366Ts working in this mode can form a stereo 6-way system. For

example purposes only, in the diagram below the first FDS-366T is running a 5

way system with the mono sub bass derived from the sum of inputs A and B.

The second FDS-366T has its mono sub bass output fed from a dedicated

output on the desk running into input C.

Mono 6-way

Typical Applications j

Stereo 6-way

(example)

- 19 -

FDS-366T

It is not possible to provide one loudspeaker driver to cover all audible

frequencies. Even if the frequency response could be achieved, the large size

of the driver required to shift enough air at low frequencies would offer an

impossibly directional beam at high frequencies because at small wavelengths,

the differing path lengths from the extremities of the diaphragm to the listener

would cause cancellations off-axis. Therefore, it is necessary to use more than

one driver and to split the bands with an electrical filter or crossover. This

filtering can be done by passive, active or digital means, external to or within

the loudspeaker cabinet.

Ideally, the filtering is done so that when acoustically combined, the drivers

produce a constant output across the required range of frequencies.

Additionally, the signal phase behavior with frequency should offer smooth

transitions across all the drivers to achieve a constant group delay. Another

important consideration is that the crossover should control the beaming

properties, also known as the polar response, so that listeners off-axis do not

hear anomalies in the sound range. Many crossover filter designs do not

achieve these goals.

Finally, the signal should be quickly attenuated outside the optimum band of

operation for each driver to avoid driver anomalies such as resonance and

over-excursion distortion at low frequencies. In these instances some crossover

shapes have limitations.

The FDS-366T allows full control over each high and low pass filter of a

crossover segment in shape, slope and frequency. Graphically these

parameters are labelled as below.

7.0 Crossover Shapes and Frequencies

Filter Edge Identification

- 20 -

FDS-366T

Crossover Shapes and Frequencies

-50.00

-45.00

-40.00

-35.00

-30.00

-25.00

-20.00

-15.00

-10.00

-5.000

0.0

5.0000

20 100 1k 10k 20k

-

0

5

Linkwitz-Riley 12, 24 & 48dB/Octave Slopes.

For many years Linkwitz-Riley crossovers have

been the 'industry standard' as they offered the

best compromise between the parameters

discussed earlier. They retain good polar

response, sum to a flat amplitude response and

retain correct polarity across the 24dB/octave and

48dB/octave slopes. The 12dB/octave variant

generally needs a polarity inversion to achieve the

required results. They have been the usual choice

for most applications.

Butterworth 6, 12, 18, 24 & 48dB/Octave Slopes.

The even order Butterworth crossovers (12, 24,

48dB/octave) exhibit a symmetrical polar response

due to identical phase responses in the Hi and Lo

bands. There is an issue with a 3dB peak in the

amplitude response at the crossover frequency but

this can be corrected with equalisation. In

contrast, the odd order Butterworths (6 & 18dB/

octave) sum to a flat amplitude response but suffer

asymmetry in their polar response that changes as

the signal moves through the crossover point. This

'tilt' can produce colouration and is dependant on

the listening position. These also require polarity

inversion for correct response.

-

0

5

Bessel 12 & 24dB/Octave Slopes.

Standard Bessel filters when used for crossover

duties do not provide immediately acceptable

results due to deficiencies in their amplitude

response. Due to this only 4th and 2nd order (Bes

24 & 12) alignments were considered to be

acceptable for inclusion. The 12dB/octave

version will require a polarity inversion of one

band for proper summation.

The graphs on this page show the filter slope curves with associated crossover points in order to aid the sound

technician in the choice of filter shape to use for the desired result between speaker drivers of differing

specifications and characteristics.

Page is loading ...

BSS Audio FDS366T OMNIDRIVE User manual

This manual is also suitable for

BSS Audio FDS366T OMNIDRIVE User manual

Related papers

Other documents