2. Computers & electronics
  3. TVs & monitors
  4. Flat panel desk mounts
  5. Atdec
  6. AWM-LTH-B

Atdec AWM-LTH-B Installation guide

  • Hello! I've reviewed the Installation Guide for the ATDEC AWM-LTH Heavy Duty VESA Tilt Head. This document outlines the steps for installing the tilt head, including attaching it to a VESA compatible monitor and adjusting the tilt tension. I'm ready to assist with any questions you may have.
  • What is the weight range supported by the tilt head?
    What tool is required for installation?
    What should I do if my monitor has a curved or uneven surface?
AWM-LTH Page 1 of 2
Installation Guide
AWM-LTH
Heavy Duty VESA Tilt Head
COMPONENT CHECKLIST
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! Curvedmonitors,deepdevices(suchasall-in-onePCs)andosetVESAlocationsexertadditionalleveragethatcanexceedthe
capacityofthemounteventhoughthemonitorweightmaybewithinthestatedrange.
! Themanufactureracceptsnoresponsibilityforincorrectinstallation.
! ThisproductiscompatiblewithAWMSeriesmonitorarmproducts:AWM-AHX,AWM-LC,AWM-A46&AWM-A71.
Monitorweightshouldbe
withintheweightrangeof
all modular elements that
make up the complete
monitormountingsolution.
REQUIRED TOOLS
• Phillips Head Screwdriver
A
Heavy Duty
Tilt Head
(x1)
B
Screw
M4x25mm
(x4)
C
Screw
M4x16mm
(x4)
D
Screw
M4x12mm
(x4)
E
Spacer
(x4)
F
4mm
allen key
(x1)
WEIGHT RANGE
0 - 18kg
(0 - 40lb)
AWM-LTH Page 2 of 2
Loosen
Tighten
atdec.com | atdec.co.uk | atdec.com.au
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specifications without notice. ©20190404
1. Attach VESA head to monitor
1.2Ensuresuitablescrewsizeisused. 1.3VESAmountingcompatibility
Note: Forothersizes,useasuitable
adaptor plate
1.1ScrewtheVESAheadontomonitor
Note:Spacersmayberequiredfor
curved, recessed or uneven monitor
surfaces.
2. Mount monitor onto arm
3.1Usetheknobtotightenandloosenthe
tilttensiontosuityourmonitorweight.
Note:Alwayssupportthemonitor
whilstadjustingtopreventitfrom
fallingforwardsharply.
Optional
Ifextratilttensionisrequiredforyour
monitor, use provided allen key to
tightensecondtiltscrew.
Loosen
Tighten
2.1 Push tilt head onto the shaft at the
endofthemonitorarm.
2.3 Tightenthejointscrewtosecure
thetiltheadandmonitorinplace.
3. Adjust tilt tension
100mm
75mm
100mm 75mm
Flush
Too long Too short
Spacer
5mm 12mm
Note: Check the arm rotation
issmoothaftertightening.
2.2Ensuretiltheadisfullypushed
ontoshaft.
100mm
75mm
100mm
75mm
Flush
Too long Too short
Spacer
5mm 12mm
/