Telldus TZWP-101 User manual

Brand
Telldus
Model
TZWP-101
Type
User manual

This manual is also suitable for

Manual version 1.0
QUICK GUIDE
PLUG-IN SWITCH
ON/OFF
Manual version 1.0
1.1
1. INCLUDING THE DEVICE IN TELLDUS LIVE!
1. LÄGGA TILL ENHETEN I TELLDUS LIVE!
Scheduler
My Devices My SensorsStart
live.telldus.com
Add a new device
live.telldus.com
1.2
live.telldus.com live.telldus.com
1.3 1.4
433,92 MHz
1.5
x3
live.telldus.com
1.6
Name this device: Bedroom lamp
Done
Manual version 1.0
1.7
2. CONTROLLING THE DEVICE
2. STYRA ENHETEN
live.telldus.com
2.1
My Deviceslive.telldus.com Bedroom lamp
live.telldus.com
2.2
3. EDIT THE DEVICE
3. REDIGERA ENHETEN
live.telldus.com
3.1
My Deviceslive.telldus.com
Bedroom lamp
live.telldus.com
3.2
Edit device
Manual version 1.0
4. EXCLUDE THE DEVICE
4. EXKLUDERA ENHETEN
live.telldus.com
4.1
My Deviceslive.telldus.com
Bedroom lamp
live.telldus.com
live.telldus.com
4.2
4.3
Edit device
Exclude device
4.4
x3
5
5. TECHNICAL MANUAL
Download complete technical manual and nd more useful information at:
www.telldus.com
Manual version 1.0
6. ASSOCIATIONS
6
Association group 1 - Lifeline - Plug status - Max 1 node
The plug will send it's status to the node in this group whenever
the status of the plug changes.
Lifeline is normally used to send the plug status to the main
controller / gateway.
Association group 2 - Control other devices - Max 10 nodes
The plug will send Basic Set control signals to the nodes in this
group whenever the status of the plug changes. This will work
like a master/slave solution.
7. CONFIGURATIONS
7
Parameter no 1 - Countdown timer
Number of minutes before it auto-shuts down.
Default value: 0 (disabled)
Size: 1 byte
Possible values: 0-254
Unit: minutes
Parameter no 2 - Remember device status after power failure.
Define how the plug will react after the power supply is back on.
Default value: 1 (remember status)
Size: 1 byte
Possible values: 0: Always o, 1: Remember status, 2: Always on.
Parameter no 3 - LED indicator
Set the intensity of the LED indicator
Default value: 255
Size: 1 byte
Possible values: 0-100
Manual version 1.0
8. RESET
8
Reset the device
Method 1
Remove the device from the Z-Wave network. This will reset the
device to factory defaults.
Method 2:
Reset the device by:
Press and hold the button until the LED starts flashing white
(approx. 6 seconds).
Press the button once more, short.
The device will now reset to factory defaults. The LED will now
flash red, indicating that it’s no longer added in any Z-Wave
network.
This procedure is called ‘Device Reset Locally’ and it should only
be used when the primary controller is missing or inoperable.
Manual version 1.0
WWW.TELLDUS.COM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Telldus TZWP-101 User manual

Brand
Telldus
Model
TZWP-101
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents