Speed Face Series

ZKTeco Speed Face Series User guide

  • Hello! I've reviewed the Quick Start Guide for the ZKTECO SpeedFace series, including models V5, H5, and T5. This document covers everything from device installation and wiring to user registration and authentication methods. It also explains how to integrate with alarm systems and how to view records. I'm here to help you with any questions you may have about your device, so feel free to ask!
  • What is the recommended power supply?
    How do I register a new employee on the device?
    What is the range for face detection?
    How to view records on the device?
Version: 1.0
Date: October 2018
Quick Start Guide
SpeedFace series
1
Device Installation
Overview
1.5m
1 2 3
Flash
Camera
5 inch touch screen
RS232
RS485
485B
485A
GND
TXD1
RXD1
GND
TXD2
RXD2
RS232
Power
Wiegand
In
Wiegand
Out
GND
12V
+12V
GND
INWD0
INWD1
W0D
W1D
ResetSpeaker
Microphone
Fingerprint sensor
Ethernet
TX+
RX+
TX-
RX-
Attach the mounting template sticker to the wall, and drill holes according
to the mounting paper. Fix the back plate on the wall using wall mounting
screws.
Attach the device to the back plate.
Fasten the device to the back plate with a security screw.
Lock
AUX
Alarm
Exit Button
Sensor
AL+
AL-
N1C
COM
N1O
BUT
GND
SEN
GND
Auxiliary
input
Card reading area
Magnetic tamper
switch
2
TCP/IP
Alarm
Smoke
detector
Lock
Exit Button
Door Sensor
Card
Reader
ZKBioAccess
Standalone Installation
AUX
AL+
AL-
N1C
COM
N1O
BUT
GND
SEN
GND
-+
-+
+-
+
-
Door Sensor, Exit Button & Alarm Connection
Door Sensor
Alarm
Alarm's power switch
Exit Button
Smoke detector
Note: In this document, we only guide you to connect some common components,
if you want more guidance on connection of SRB, external fingerprint reader and so
on, please refer to user manual document.
3
Lock Relay Connection
The system supports Normally Opened Lock and Normally Closed Lock.
-
-
+
-
+
DC12V
+
-
+
GND
+12V
F 107R
AUX
AL+
AL-
N1C
COM
N1O
BUT
GND
SEN
GND
The NO LOCK (normally opened at power on) is connected with 'NO1' and
'COM' terminals, and the NC LOCK (normally closed at power on) is connected
with 'NC1' and 'COM' terminals. T NC Lock below:ake as an example
Normally Closed Lock
DC12V
1) Device not sharing power with the lock
+
-
-
+
DC12V
+
-
GND
+12V
F 107R
AUX
AL+
AL-
N1C
COM
N1O
BUT
GND
SEN
GND
Normally Closed Lock
2) Device sharing power with the lock
4
RS485 and RS232 Connection
TXD
RXD
GND
RS232
Reader
Wiegand Input Connection
WD0
WD1
+12V
GND
Wiegand Reader
+12V
IDW1
IDW0
GND
485B
485A
GND
TXD1
RXD1
GND
TXD2
RXD2
485+
485-
GND
RXD
GND
TXD
RS232
Reader
RS485
Reader
5
Power Connection
Ethernet Connection
12V
GND
GND
12V DC
Recommended power supply
1) 12V ± 10%, at least 00mA.30
2) To share the power with other devices, use a power supply
with higher current ratings.
Default IP address: 192.168.1.201
Subnet mask: 255.255.255.0
Click [Settings] > [Network Settings] > [TCP/IP Settings] > [DHCP], input the IP address
and click [OK].
Note: In LAN, IP addresses of the server (PC) and the device must be in the
same network segment when connecting to ZKBioAccess software.
IP address: 192.168.1.130
Subnet mask: 255.255.255.0
8
7
6RJ 45
5
4
3
2
1
RX
TX+
TX-
RX-
ZKBioAccess
6
Quick Start
User Registration
User Authentication
View records
Verified
User registration
Register on the device
Click > Employee > to register new employee. Enter employee name, ID,
register fingerprint, face, badge number (ID and Mifare card are optional), and
password.
L
L
L
Note:
1. It's recommended to register multiple administrators.
2. It's recommend enroll user's face in 0.5med to
distance for person with1.4~1.8m height .
05m.
1.5m
14m18m.-.
7
Register on the software
Note: The icons or in the standby interface indicates that the network
connection or the server is abnormal. Please check the network cable and network
connection.
Please set the IP address and cloud service server address on the device.
2. Click [Personnel] > [Person] > [New] to register users in the software.
3. Add users to access levels.
4. Click [Access] > [Device] > [Device Control] > [Synchronize All Data to Devices].
For more details, please refer to the ZKBioAccess User Manual.
1. Click [Access] > [Access Device] > [Device] > [Search Device] to add the device to
the software.
When the device has set the server address and port, it can be added automatically.
Step 1
Step 2
Step 3
Step 4
8
Register on the phone
Login onto http://X.X.X.X:XX/app/v1/adreg with mobile phone browser application
to register users.
Cloud server IP address Server port
Verification is successful
User Authentication
Terminal could detect face in 0.3m to maximum
3m distance. The device switches to face
verification interface automatically once it detect
bright of environment change. The verification
result shows as right image.
The users will display in [Personnel] > [Temporary Personnel], click [Review].
Once ZKBioAccess software installation, users could enroll face via broswer
application on their own mobile phone.
9
View records
View records in the device
Click > > enter or (if user IDRecord Search Att Log Name Employee ID
field is empty, records of all users will be displayed) > select > pressTime Range
, the corresponding attendance logs will be displayed.OK
Record Search Att Log Name Employee ID
Time Range
OK
View records on the software
Click [Access] > [Report] on the software to view the records.
L
L
10
ZK Building, Wuhe Road, Gangtou,
Bantian, Buji Town, Longgang
District, Shenzhen China 518129
Tel: +86 755-89602345
Fax: +86 755-89602394
www.zkteco.com
© Copyright 2018. ZKTECO CO., LTD. ZKTeco Logo is a registered trademark of ZKTeco or a
related company. All other product and company names mentioned are used for identification
purposes only and may be the trademarks of their respective owners. All specifications are
subject to change without notice. All rights reserved.
Device name
Appearance
SpeedFace V5
SpeedFace H5
SpeedFace T5
Appendix
/