ZKTeco ZK_PA22 User guide

Brand: ZKTeco

Model: ZK_PA22

Category: Security door controllers

Type: User guide

PA22

Version: 1.0

Quick Start Guide

Due to the regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between

the actual product and the written information in this manual.

Side

Bottom

Back Plate

Reset Button

Speaker

USB Slot

Front

Back

2.4 Inch TFT LCD

Keypad &

RF Card Area

LED Indicator

Near-infraredPalm

RecognitionSensor

Tamper switch

Terminal Block

Wiring Hole

Mounting Hole

Device Overview

6.29"

(159.8mm)

4.97"

(126.1mm)

3.18"

(80.7mm)

0.76"

(19.4mm)

1.61"

(41.0mm)

47.24"

(1.2m)

Baseline

124

Install on the Wall

(56.1mm)

2.21"

Device Dimensions

Device Installation

Attach the mounting template sticker to the wall, and drill the holes according

to the mounting paper.

Fix the back plate on the wall with using wall mounting screws.

Attach the device to the back plate from top to bottom.

Fasten the device to the back plate with a security screw.

485B

485A

GND

TXD

RXD

GND

WD1

WD0

RS485B

RJ45-1

RJ45-2

RJ45-3

RJ45-6

AUX

GND

BELL-

BELL+

SEN

GND

BUT

NO1

COM1

NC1

AL-

AL+

BEEP

GLED

RLED

IWD1

IWD0

GND

12VOUT

BEEP

Green LED

Red LED

GND

+12V

Ethernet

RS232

Lock

Power Out

Sensor

Button

Power In

Auxiliary

Bell

Alarm

Wiegand

Out

Wiegand

8 Pin Cable Connectors

7 Pin Cable Connectors

4 Pin Cable Connectors

12 Pin Cable Connectors

2 Pin Cable Connectors

Terminal Block

Standalone Installation

Alarm

Bell

Lock

TCP/ IP

Exit Button

Door Sensor

ALARM

Wireless Router

GND

+12V DC

12V DC Adaptor

Power Connection

Without UPS

GND

+12V DC

With UPS (Optional)

12V±10%, at least 3000MA.

Use an AC adapter with a higher current ratings to share the power with other

devices.

Recommended Power Supply:

Ethernet Connection

LAN Connection

Network Cable Adaptor

RJ45-1

RJ45-2

RJ45-3

RJ45-6

Default IP address: 192.168.1.201

Subnet mask: 255.255.255.0

IP address: 192.168.1.130

Subnet mask: 255.255.255.0

Door Sensor, Exit Button, Alarm & Bell Connection

Door Sensor

Bell

Alarm

Exit Button

12V DC Adaptor

+12V DCGND

AUX

GND

BELL-

BELL+

SEN

GND

BUT

NO1

COM1

NC1

AL-

AL+

Connect the device and the software over an Ethernet cable. An example is

shown below:

Click [Comm.] > [Ethernet] > [IP Address], input the IP address and click

[M/OK].

Note: In LAN, the IP addresses of the server (PC) and the device must be in the

same network segment when connecting to ZKBio Access IVS software.

Lock Relay Connection

12V DC Adaptor

Magnetic Lock

+12V DC GND

FR107

Device Not Sharing Power with the Lock

AUX

GND

BELL-

BELL+

SEN

GND

BUT

NO1

COM1

NC1

AL-

AL+

DO NOT REVERSE

THE CONNECTION.

V- V+

NC NO

COM

Magnetic Lock

FR107

Device Sharing Power with the Lock

AUX

GND

BELL-

BELL+

SEN

GND

BUT

NO1

COM1

NC1

AL-

AL+

V- V+

NC NO

COM

AC Adapter

DC 12V, 3A

GND

+12V

DO NOT REVERSE

THE CONNECTION.

The system supports both Normally Opened Lock and Normally Closed Lock. The

NO Lock (Normally Opened when powered) is connected with “NO” and “COM”

terminals, and the NC Lock (Normally Closed when powered) is connected with

“NC” and “COM” terminals. The power can be shared with the lock or can be used

separately for the lock, as shown in the example with NC Lock below:

RS485 Connection

RS485 Fingerprint Reader Connection

RS485 Fingerprint Reader

DIP Settings

485-

485+

GND

+12V

GND

Distance:

more than 200 meters

485B

485A

GND

TXD

RXD

GND

WD1

WD0

12V DC Adaptor

There are six DIP switches which are located on the back of RS485 ngerprint

reader: switches 1 to 4 are for RS485 address, switch 5 is reserved, switch 6 is for

noise reduction on long RS485 cable.

If the RS485 ngerprint reader is powered from the terminal, the length of

wire should be less than 100 meters or 330 feet.

The number 6 switch should be turned on if the cable length exceeds 200

metres or 600 feet as shown below.

Wiegand Output Connection

Controller

READER 1

BEEP

GLED

WD1

WD0

GND

+12V

485B

485A

GND

TXD

RXD

GND

WD1

WD0

Wiegand Input Connection

BEEP

GLED

RLED

IWD1

IWD0

GND

12VOUT

Wiegand Reader

BEEP

GLED

RLED

DATA1

DATA0

GND

+12V

AC Adapter

DC 12V, 3A

GND

+12V

Device Operation

User Registration

When there is no super administrator set in the device, click [M/OK] to enter the

menu. Add a new user and set their User Rule to Super Admin, then the system

will ask for the administrator’s approval before allowing them to access the menu.

For security reasons, we highly recommend that you register a super administrator

promptly.

Click [M/OK] > [User Mgt.] > [New User] to register a new user. The options

includes entering the User ID and Name, setting User Role, registering Palm, Card

Number, Password, and setting Access Control Role.

The following takes the registered palm as an example.

Note: While registering, please keep the yellow circle at the bullseye position as

much as possible.

Click [M/OK] > [COMM.] > [Ethernet] to set the network parameters. If the

TCP/IP communication of the device is successful, the icon will be displayed in

the upper right corner of the standby interface.

Click [M/OK] > [COMM.] > [Cloud Server Setting] to set the server address and

server port, i.e., the IP address and port number of the server after the

software is installed. If the device communicates with the server successfully, the

icon will be displayed in the upper right corner of the standby interface.

Ethernet and Cloud Server Settings

Wireless Network Settings

To congure the Wi-Fi, click [M/OK] > [COMM.] > [Wireless Network].

When the Wi-Fi connection is enabled, select the searched network. Enter the

password, and click [Connect to WIFI (OK)]. The connection is established, with

Wi-Fi icon displayed on the status bar.

Access Control Setting

Click [M/OK] > [Access Control] to enter the access control management

interface and set relevant parameters for the access control.

Attendance Record

Click [M/OK] > [Attendance Search] > [Attendance Record] to enter the

records query interface, input the user ID and select the time range. The

corresponding attendance logs will then be displayed.

ZKTeco Industrial Park, No. 32, Industrial Road,

Tangxia Town, Dongguan, China.

Phone : +86 769 - 82109991

Fax : +86 755 - 89602394

www.zkteco.com

ZKTeco ZK_PA22 User guide

Brand: ZKTeco

Model: ZK_PA22

Category: Security door controllers

Type: User guide

Download PDF

report

ZKTeco ZK_PA22 User guide

ZKTeco ZK_PA22 User guide

Related papers

Other documents