Extron electronics SMD 101 User manual

68-2231-01 Rev. D

03 21

H.264 Streaming Media Decoder

(FW version 2.05.0000)

SMD 101

User Guide

Streaming AV Products



Copyright

Trademarks

All trademarks mentioned in this guide are the properties of their respective owners.

The following registered trademarks (

®

), registered service marks (

SM

), and trademarks (

TM

) are the property of RGBSystems, Inc. or Extron (see the

current list of trademarks on the Terms of Use page at www.extron.com):

Registered Trademarks

(

®

)

Extron, Cable Cubby, ControlScript, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, eLink, Flat Field, FlexOS, Glitch Free, GlobalConfigurator,

GlobalScripter, GlobalViewer, Hideaway, HyperLane, IPIntercom, IPLink, KeyMinder, LinkLicense, LockIt, MediaLink, MediaPort, NAV,

NetPA, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, ShareLink, Show Me, SoundField, SpeedMount, SpeedSwitch, StudioStation,

SystemINTEGRATOR, TeamWork, TouchLink, V-Lock, VideoLounge, VN-Matrix, VoiceLift, WallVault, WindoWall, XPA, XTP, XTPSystems, and ZipClip

Registered Service Mark

(SM)

: S3 Service Support Solutions

Trademarks

(

™

)

AAP, AFL (Accu-RATEFrameLock), ADSP(Advanced Digital Sync Processing), AVEdge, CableCover, CDRS(ClassD Ripple Suppression),

CodecConnect, DDSP(Digital Display Sync Processing), DMI (DynamicMotionInterpolation), DriverConfigurator, DSPConfigurator, DSVP(Digital

Sync Validation Processing), EQIP, Everlast, FastBite, Flex55, FOX, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital, Opti-Torque,

PendantConnect, ProDSP, QS-FPC(QuickSwitch Front Panel Controller), RoomAgent, Scope-Trigger, SIS, SimpleInstructionSet, Skew-Free,

SpeedNav, Triple-Action Switching, True4K, True8K, Vector™ 4K, WebShare, XTRA, and ZipCaddy

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause interference. This interference must be corrected at the

expense of the user.

NOTE: For more information on safety guidelines, regulatory compliances, EMI/EMF

compatibility, accessibility, and related topics, see the Extron Safety and Regulatory

Compliance Guide on the Extron website.

Battery Notice

This product contains a battery. Do not open the unit to replace the battery. If the

battery needs replacing, return the entire unit to Extron (for the correct address, see the

Extron Warranty section on the last page of this guide).

CAUTION: Risk of explosion. Do not replace the battery with an incorrect type. Dispose

of used batteries according to the instructions.

ATTENTION : Risque d’explosion. Ne pas remplacer la pile par le mauvais type de pile.

Débarrassez-vous des piles usagées selon le mode d’emploi.

VCCI-A Notice

この装置は、クラスＡ情報技術装置です。この装置を家庭環境で使用すると、電波妨害を引き

起こすことがあります。その場合には使用者が適切な対策を講ずるよう要求されることがあります。

ＶＣＣI－Ａ

Conventions Used in this Guide

Notifications

The following notifications are used in this guide:

CAUTION: Risk of minor personal injury.

ATTENTION : Risque de blessuremineure.

ATTENTION :

• Risk of property damage.

• Risque de dommages matériels.

NOTE: A note draws attention to important information.

TIP: A tip provides a suggestion to make working with the application easier.

Software Commands

Commands are written in the fonts shown here:

^AR Merge Scene,,0p1 scene 1,1 ^B 51 ^W^C.0

[01] R 0004 00300 00400 00800 00600 [02] 35 [17] [03]

E X! *X1&* X2)* X2#* X2! CE}

NOTE: For commands and examples of computer or device responses used in this

guide, the character “0” is used for the number zero and “O” is the capital letter “o.”

Computer responses and directory paths that do not have variables are written in the font

shown here:

Reply from 208.132.180.48: bytes=32 times=2ms TTL=32

C:\Program Files\Extron

Variables are written in slanted form as shown here:

ping xxx.xxx.xxx.xxx —t

SOH R Data STX Command ETB ETX

Selectable items, such as menu names, menu options, buttons, tabs, and field names are

written in the font shown here:

From the File menu, select New.

Click the OK button.

Specifications Availability

Product specifications are available on the Extron website, www.extron.com.

Extron Glossary of Terms

A glossary of terms is available at http://www.extron.com/technology/glossary.

aspx.

Introduction .................................................... 1

About this Guide ................................................. 1

About the SMD101 ............................................ 1

Video Output .................................................. 3

Output Resolution and EDID Support Table ... 5

Suggested PC Requirements .......................... 6

Supported formats: ........................................ 6

Features ............................................................. 7

Panels and Cabling ......................................... 9

Front Panel Features ........................................... 9

Rear Panel Features ......................................... 10

SMD101 Rear Panel Reset .......................... 13

SMD101 Power Up Procedure ........................ 14

Hardware Setup Overview ................................ 14

Web-based User Interface ........................... 15

Overview of the Web-based User Interface ....... 15

Web Browser Requirements ............................. 15

Accessing the Embedded Web Pages .............. 16

Overview of the SMD 101

Embedded Web Pages ................................... 16

Tabs ............................................................. 17

Pages Within Tabs ........................................ 17

Panels and Screen Sections ......................... 18

Collapsing and Expanding Panes .................. 18

Web Page Idle (Timeout) ................................... 19

Logging Out and Logging In ............................. 19

Player Page Overview ....................................... 22

Player Controls Features ............................... 23

Player Page Layout ........................................... 28

Browser ........................................................ 29

Browser Panel - Streams .............................. 29

Browser Panel - Files .................................... 32

Folder Playlists.................................................. 37

Lists.............................................................. 38

Playlist Editor ................................................ 41

Conﬁguration Page ........................................... 46

Configuration Page Features ......................... 46

Video Configuration

...................................... 47

Audio Configuration

...................................... 54

On Screen Display ........................................ 56

Configuring the On-Screen Displays ............. 59

Automation ................................................... 60

Folder Playlist Configuration .......................... 64

Advanced Conﬁguration Page .......................... 66

Connection .................................................. 67

Firmware Loader ........................................... 74

Exec/Power Mode ........................................ 78

Date and Time .............................................. 81

Password ..................................................... 82

Reset Device ................................................ 85

Alarms .......................................................... 86

Device Information Page ................................... 88

Troubleshooting ................................................ 90

Status ........................................................... 90

Logs Page .................................................... 93

Alarm History Page ....................................... 95

Diagnostics Page .......................................... 97

Advanced Player Conﬁguration ................. 100

Loading Content to Local Storage

Using SFTP ................................................... 100

Play Video on Demand ................................... 103

Play Video from a Network Share ............... 103

SME100 Stream Discovery ............................ 106

Connecting to Streams Without SAP

Announcements ............................................ 107

UDP or RTP Connections ........................... 107

HTTP Connection to an SME100 ............... 108

IR Remote Control ...................................... 110

Contents

SMD101 • Contents v

Remote Communication and Control ........ 111

Connection Options ........................................ 111

RS-232 Port ............................................... 111

Front Panel Configuration Port .................... 112

LAN (Ethernet) Port......................................... 113

Host and Device Communications .................. 115

SMD101-initiated Messages ...................... 115

Copyright Information ................................. 115

Password Information ................................. 115

Error Responses ......................................... 116

Using the Command and

Response Tables ....................................... 116

Command and Response Tables .................... 120

Basic SIS Commands ................................. 120

Player SIS Commands ................................ 126

Reference Information ............................... 134

Parts and Accessories .................................... 134

Mounting the SMD101 .................................. 134

Tabletop Use .............................................. 134

Rack Mounting ........................................... 135

Furniture Mounting...................................... 135

Table or Wall Mounting ................................ 135

SMD101 Reset Summary .............................. 136

Supported File Types ..................................... 138

Supported network file share protocols ....... 138

Optimum Network Share Performance ........... 139

Network Shares Dialog ............................... 139

Conﬁguring Windows 7 for Network

File Sharing .................................................... 140

Firewalls ..................................................... 146

DataViewer ..................................................... 146

Start the DataViewer program ..................... 146

Secure Sockets Layer (SSL) Certiﬁcates ......... 147

IEEE 802.1X Certiﬁcates ................................. 148

Certificate File Requirements....................... 148

Private Key File Requirements ..................... 149

Glossary ......................................................... 150

SMD101 • Contents vi

Introduction

This section gives an overview of the user guide and describes the SMD101 and its

features. Topics that are covered include:

• About this Guide

• About the SMD101

• Features

About this Guide

This guide contains installation, configuration, and operating information for the SMD101.

In this guide:

• Codec or H.264 refers to the H.264/MPEG-4 Part 10 AVC codec.

• Stream can refer to audio, video, or both that is received by the SMD101 and

constantly decoded for display.

• Unless otherwise noted, web pages and pages refer to the embedded web-based

configuration software of the SMD 101.

About the SMD101

The SMD101 is a compact, high performance H.264 decoder used in applications that

require live AV streaming or file playback from files located on shared network storage

devices. The SMD101 can decode and display one SD or HD stream and output a single

HDMI signal supporting resolutions up to 1920x1200 (60 fps, progressive). The video output

can be scaled and its aspect ratio modified. The Extron SMD101 is compatible with content

from all Extron H.264 streaming products including the SME100 and SMPseries products.

The SMD101 can be controlled using IR, and from the RS-232 and Ethernet ports. Ethernet

to RS-232 pass-through for display control is possible.

The SMD101 decodes H.264/MPEG-4 AVC streams or clips and outputs HDMI video with

embedded or analog audio for display on any HDMI compatible device (see figure 1 on the

next page).

SMD101 • Introduction 1

Extron

SMD 101

Streaming

Media Decoder

12V

--A MAX

POWER

HDMI

L R

AUDIO

Tx Rx G

S G

RS-232

RESET

IR IN

LAN

OUTPUTS

Sound System

Extron

SI 26

Surface-mount

Speakers

Extron

XPA 1002

Stereo Power

Amplier

Extron

TLP 700TV

Touch Panel

Local Storage

(internal)

Network Attached

Storage

a

c

b

HD Display

HDMI/RGB/Analog

HDMI/RGB

Audio

Ethernet

Select:

a NAS

b

Stream

c Local

Extron

ON

OFF

DISPLAY

MUTE

SCREEN

UP

SCREEN

DOWN

VCR

DVD

DOC

CAM

LAPTOP

PC

Internet/

Network

1

2

LIMIT

ER/PROTECT

SIGNAL

O

VER

T

EMP

XPA 100

2

Extron

SME 100

Streaming

Encoder

SME 100

STREAMING M

EDIA EN

CODER

ADJUST

1

MENU NEXT

2

3

CONFIG

Figure 1. Typical SMD101 Application

figure 1

SMD101 • Introduction 2

The optional handheld IR remote control allows channel preset recall and channel

navigation. The SMD101 automatically detects transport and stream formats and decodes

the content for presentation to the display.

A channel list can be defined that allows simple selection of individual streams. The user can

import or export source selection data including URLs and associated data from the channel

list. This is an extension of the configuration save or restore capability that can save box and

IP configuration settings for the product as a separate file.

The channel list can be accessed with an optional remote control for selection and playing

streams included in the list.

The SMD101 decodes all common stream resolutions and frame rates.

The SMD101 can be configured using a host PC or laptop connected to the front

panel USB Config port, the RJ-45 LAN connector, or the RS-232 port (see Remote

Communication and Control on page111). A compatible web browser on a control PC

connected to the same network as the SMD101 can access the embedded HTML pages.

A video confidence display allows image monitoring from the user interface while making

configuration and control adjustments.

Video Output

Video output parameters are configured automatically for the connected display based

on the display EDID, or can be configured manually using a browser and the video

configuration page.

NOTE:

• The SMD101 does frame rate conversion between the input stream frame rate and

the output frame rate, scaling from the source resolution and output resolution, and

aspect ratio between ﬁt (zoom), ﬁll, and follow as required.

• Fill and follow background, when necessary, is black.

By default, the SMD101 automatically outputs video corresponding to EDID data from the

connected display within the resolution and rate combinations (see Output Resolution and

EDID Support Table on page5). The output rates available are limited by the display

capabilities. EDID data exchange is compatible with E-EDID V2.0 (EDID data structure 1.4)

and EIA/CEA-861E.

SMD101 • Introduction 3

CEC control

Starting with firmware version 2.05, the SMD has the option to control the power state

and input selection of a display connected to the HDMI output. The extent of the control

is Automatic Limited Functionality. CEC control can be enabled or disabled via SIS

command (see Output CEC Mode on page133). CEC control is disabled by default. CEC

communication with any source connected to the HDMI input of the SMD is not supported.

External control of CEC communication is not supported. Automatic Limited Functionality is

defined as follows:

• When the SMD product powers on or transitions from standby mode to normal

operation, the SMD sends Power on and Show Me commands to the display

connected to its HDMI output.

• When the SMD product transitions from HDMI sync mute to HDMI sync active state, the

SMD sends Power On and Show Me commands to the display connected to its HDMI

output.

• When the SMD product transitions from HDMI sync active to HDMI sync mute state, the

SMD sends the Power Off (standby) command to the display on its HDMI output.

• When the SMD product transitions from normal operation to standby mode, the SMD

sends the CEC Power Off (standby) command to the display on its HDMI output.

NOTES:

• In accordance with the CEC standard (HDMI 1.3 supplement 1) the display adopts

logical address 0 (TV) and the SMD adopts logical address 14 (free use). Translation

to CEC standard command terminology:

• Power On — Image View On to logical address 0 (TV).

• Power Off — Standby to logical address 0 (TV).

• Show Me — Active Source broadcast indicating the physical address from the

display EDID. The Show Me command is broadcast to allow any other devices

to take appropriate action.

• There are variations in the way CEC is implemented between different

manufacturers. Extron strives to accommodate these variations and to ensure

reliable operation, but not all display makes and models are tested. Please report

any inconsistencies.

• Many displays do not support CEC control. Most displays that do support CEC

include settings to enable, disable, and conﬁgure CEC control and must be

conﬁgured correctly to ensure reliable operation. The term used for CEC control

varies between manufacturers.

SMD101 • Introduction 4

Output Resolution and EDID Support Table

Resolution 23.98 Hz 24 Hz 25 Hz 29.97 Hz 30 Hz 50 Hz 59.94 Hz 60 Hz

640x480 10 11

800x600 12 13

1024x768 14 15

1280x1024 16 17

1366x768 18 19

1600x1200 20 21

1920x1200 22 23*

480p 24 25

576p 26

1280x800 27 28

720p 32 33 34

(default)

1080i 35 36 37

1080p 38 39 40 41 42 43 44 45*

NOTES:

• Numbers indicate the EDID preset resolution.

• * With reduced blanking.

• Highest resolution is 1920x1200 (158.25 MHz@50 Hz and 154 MHz@60 Hz*).

• Highest pixel rate is 1600x1200 @ 60 Hz (162 MHz).

For applications where the EDID settings do not provide or allow the desired results, select

a video output from the table. Select a defined output rate combination supported by the

display, or set the video output to match the input stream.

If required, the output may be muted automatically after a defined period of inactivity to

allow connected displays to enter standby mode. Alternately, it is muted and unmuted under

user control. Video mute settings are cleared during reboot or power cycle events (see

Configuration Page on page46).

SMD101 • Introduction 5

Suggested PC Requirements

The suggested PC requirements to access the default web pages of the SMD101 are listed

below.

• Hardware

• 2.0 GHz dual-core processor

• Operating Systems

• Microsoft

®

Windows

®

7 or higher

• Mac

®

OS

®

X

®

10.6 or higher

To view the SMD 101 embedded web pages, use one of the supported web browsers (and

versions) listed below in order of preference.

• Web Browsers

• Google

®

Chrome™ (version 37 or higher)

• Mozilla

®

Firefox

®

(version 35 or higher)

• Apple

®

Safari

®

version 8 or higher (for Mac OS X operating systems)

NOTES:

• Web browsers can only connect to the web-based user interface via HTTPS.

Attempts to connect via HTTP will be automatically redirected.

• The SMD101 embedded web pages are designed for viewing in a browser at

100% zoom. The appearance of individual pages can differ from those in this user

guide for other zoom ratios.

Supported formats:

• File Formats

• MPEG2 TS MPEG-2 part 1 (or ISO/IEC 13818-1 or ITU-T Rec. H.222.0)

• MP4 (including mp4, m4a, m4v file extensions, not case sensitive).

• TS, m2t, m2ts, 264.s

• MOV and FLV (supports only files that use H.264 encoding and AAC audio)

• Streaming Container Formats: MPEG2 Transport stream (including .ts, .m2ts, .m2t

file extensions, not case sensitive)

NOTE: Adaptive bit rate streams are not supported.

The SMD101 can play video on demand from network shares and local storage supporting

the following file types:

Video: mp4, ts, m2t, m2ts, mov*, 264, m4v, and flv*.

NOTE: *Supports files that use H.264 encoding and AAC audio only.

Images: bmp, jpg, jpeg, tif, tiff, png, and gif.

NOTE: TIFF files using JPEG compression are not supported.

Audio: wav, aac, and m4a.

Playlists: jspf, m3u, m3u8, pls, and xspf.

NOTE: Some m3u8 playlists generated by third party software are not supported.

SMD101 • Introduction 6

Features

• Supports live IP video stream decoding — Combine with the SME100 and SMP

300 series products to provide a complete end-to-end streaming solution.

• Supports decoding streams with resolutions from 480x320 up to 1080p/60 —

Supports a wide range of resolutions to meet varying network conditions, topologies,

source and display requirements.

• AV media file playback from network shares — Use as a playback device for

on-demand playback of network-accessible media files.

• Compatible with MP4 and MPEG-2 Transport Stream container formats —

Playback common H.264 media player formats from accessible network drives.

• Stereo or dual mono audio output format: Embedded HDMI digital audio or

analog stereo audio — Flexible, cost effective use of display speakers or existing

audio systems.

• Integrated scaler offers selectable output resolutions from 640x480 to

1920x1200 — Wide range of output resolutions ensure that consistent, reliable image

quality is presented on many different types of displays.

• Decode at native resolution — The output rate and resolution can be configured to

automatically follow the native format of the connected display.

• EDID defined scaling — The output rate and resolution can be configured for

automatic selection based on EDID communication with the connected display.

• Bidirectional Ethernet to RS-232 pass through control — Integration friendly

Ethernet to RS-232 pass through for display control.

• Fill/Follow/Fit (zoom) Aspect Ratio Management — Decoded video can fill a

display, maintain aspect ratio, or maintain uniformity, presenting imagery that meets

customer expectations.

• Control from IR remote, wired IR, RS-232, Ethernet, or embedded Web

interface— Select from a range of control options to manage the SMD 101 for

stand-alone operation or as part of an AV system.

• Compatible with the full range of SME 100 and SMP 300 series streaming

transport protocols— Providing the flexibility to apply the most appropriate protocol

based on various streaming system requirements and network conditions.

• Compatible with unicast and multicast push, or pull streaming applications—

Support for push and pull streaming makes the SMD 101 compatible with different

network topologies and streaming system configurations.

• Upload and display image files — Upload PNG, JPG, TIFF (TIFF with JPEG

compression not supported), or BMP image files at resolutions up to 1920x1080 to

present familiar imagery or organizational branding, either on demand or in times of

network or streaming disruption.

• On-screen messaging — On-screen presentation of operating status or channel

selection aids in channel selection, system configuration, and troubleshooting.

• HDMI output — Compatible with HDMI and DVI digital displays.

• Automatic negotiation of streaming transport protocols with SME 100 and SMP

300 series products — Makes configuration and operation of Extron H.264 streaming

products easy in various streaming and network configurations.

• Easy-to-use embedded Web interface — Embedded web interface makes

configuration and deployment a simple activity.

SMD101 • Introduction 7

• Playback controls including progress bar — On-screen playback controls present a

visual indication of Time and Pause status, allowing for efficient control of content.

• Compatible with many third party H.264 encoders — Decode 720p/60 and

1080p/60 streaming video from an Extron SME100 and SMP 300 series or other

compatible H.264 encoders.

• Compatible with H.264 Baseline, Main, and High profiles up to and including

level 4.2 — Offers the flexibility to efficiently decode and present streaming video at

various bit rates and coding complexity.

• Support for both CAVLC and CABAC encoding

• Decoder status reporting — Simplify configuration and troubleshooting activities with

on-screen status reporting to ensure continuous, reliable operation.

• Front-accessible USB configuration port — Front-accessible port provides easy

access for system configuration and control from a PC.

• Compact and energy efficient — Efficient, low power use generates very little heat,

making it easy to optimize rack space and maintain lower operating costs.

SMD101 • Introduction 8

Panels and Cabling

This section provides information on:

• Front Panel Features

• Rear Panel Features

• SMD101 Power Up Procedure

• Hardware Setup Overview

Front Panel Features

The front panel of the SMD101 is shown in figure 2 below.

SMD 101

IR

CONFIG

A

AB

B

BC

C

CD

D

DE

E

A

Power LED

D

IR receiver window

B

Playback status indicator

E

Config port

C

Network status indicator

Figure 2. SMD101 Front Panel

A

Power LED — Dual color LED lights solid green when the SMD101 is powered. Lights

solid red when in standby (low power) mode.

B

Playback status indicator — Dual color LED indicates playback operation:

• Solid Green — The SMD101 is actively decoding a source (clip, image, or

stream).

• Blinking Green — A source (clip, image, or stream) is selected, but playback is

paused.

• Off — The selected stream is not being decoded.

• Solid Red — Unable to load (or play) the selected source.

C

Network status indicator — Dual-color LED indicates network operation and

connection or stream quality:

• Solid Green — Indicates network conditions are favorable for the current source.

The LED is also green if the current source is a local file (see Browser Panel -

Files on page32).

• Red/Green — When flashing red and green, indicates encoder or network

conditions could compromise image or audio quality, and buffers could be

depleted.

• Red — When lit, indicates degraded server or network conditions are

compromising video or audio quality and may have depleted the buffers.

• Off — No network connection.

NOTE: In many cases, the error correction features of the SMD101 allow good

image quality even when degraded network conditions are indicated.

figure 2

SMD101 • Panels and Cabling 9

D

IR Receiver Window— Allows remote operation using an optional compatible IR hand

control.

E

Config port — Connect a control PC or other USB device to this port using a

Mini-B USB cable (not supplied). Use this port to send Simple Instruction Set (SIS)

commands to the SMD101 for device configuration and control.

• For information on connecting a control PC or other USB device to this port, see

the Front Panel Configuration Port section on page 112.

• For information on SIS commands, see Remote Communication and Control on

page 111.

Rear Panel Features

The rear panel of the SMD101 is shown in figure 3 below.

12V

1.0A MAX

POWER

HDMI

LR

AUDIO

Tx Rx G

SG

RS-232

RESET

IR IN

LAN

OUTPUTS

G

GA

A

AB

B

BC

C

CD

D

DE

E

EF

F

A

12 VDC power connector

E

RS-232 connector

B

HDMI output connector

F

Reset button and LED

C

Analog audio output

G

RJ-45 LAN connector

D

IR receiver input

Figure 3. SMD101 Rear Panel

A

12 VDC power input — Connect the provided 12VDC power supply to the rear panel

3.5 mm, 5-pole captive screw connectors. When power is connected, the front panel

power indicator lights green (see figure 2,

A

on page 9).

AC Power Cord

Ground

+12 VDC

External

Power Suppl

y

(12 VDC, 1 A

)

POWER

12V

1.0A MAX

Rear Panel

Power Receptacle

Figure 4. Power Supply Connection

figure 3

SMD101 • Panels and Cabling 10

ATTENTION: Risk of property damage:

ATTENTION : Risque de dommages matériels:

• Always use a power supply provided by or speciﬁed by Extron.

• Utilisez toujours une source d’alimentation fournie ou recommandée par

Extron.

• If not provided with a power supply, this product is intended to be supplied by a UL

Listed power source marked “Class 2” or “LPS” and rated output 12Vdc, minimum 1.0 A

minimum.

• Si le produit n’est pas fourni avec une source d’alimentation, il doit être alimenté par une

source d’alimentation certiﬁée UL de classe 2 ou LPS, avec une tension nominale 12

Vcc, 1 A minimum.

• Use of an unauthorized power supply voids all regulatory compliance

certiﬁcation and may cause damage to the supply and the end product.

• L’utilisation d’une source d’alimentation non autorisée annule toute conformité

réglementaire et peut endommager la source d’alimentation ainsi que le

produit ﬁnal.

• Unless otherwise stated, the AC/DC adapters are not suitable for use in air

handling spaces or in wall cavities.

• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour

une utilisation dans les espaces d’aération ou dans les cavités murales.

• The power supply must be located within the same vicinity as the Extron AV

processing equipment in an ordinary location, Pollution Degree 2, secured to a

podium, a desk, or an equipment rack within a dedicated closet.

• La source d’alimentation doit être située à proximité de l’équipement

audiovisuel Extron dans un emplacement habituel, avec un degré de pollution

2, ﬁxée à une estrade, un bureau, ou dans une baie technique à l’intérieur d’un

placard dédié.

• The installation must always be in accordance with the applicable provisions of

National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical

Code part 1, section 16.

• Cette installation doit toujours être en accord avec les mesures qui s’applique

au National Electrical Code ANSI/NFPA70, article725, et au Canadian

Electrical Code, partie1, section16.

• The power supply shall not be permanently ﬁxed to building structure or similar

structure.

• La source d’alimentation ne devra pas être ﬁxée de façon permanente à une

structure de bâtiment ou à une structure similaire.

B

HDMI output connector — Connect an HDMI (or DVI with suitable adapter) display

device to the HDMI output connector. The EDID of a connected display is read and the

output automatically configured.

C

Analog audio output connector — Connect audio output devices using cables with

balanced or unbalanced 3.5mm, 5-pole captive screw connectors. See figure 5 below

to wire the connectors.

ATTENTION: For unbalanced audio, connect the sleeves to the ground contact.

DO NOT connect the sleeves to the negative (–) contacts.

ATTENTION : Pour l’audio asymétrique, connectez les manchons au contact au

sol. Ne pas connecter les manchons aux contacts négatifs (–).

SMD101 • Panels and Cabling 11

Balanced Audio Output

Tip

Ring

Tip

Ring

LR

Slee

ves

Unbalanced Audio Output

Tip

LR

Sleeves

Do not tin the wires!

Figure 5. Audio Output Captive Screw Connector Wiring

D

IR IN — Connect a remote IR receiver to this 3-pole, 3.5 mm captive screw connector

to extend the range of the hand control.

+

S

From

IR Receiver

SMD 101

IR IN

G

Figure 6. IR In Wiring

E

RS-232 connector (optional) — Connect a host computer or control system to the

3-pole, 3.5 mm captive screw connector or to the local device if pass-through mode

is used. Use this port to send SIS commands to the SMD101 for device configuration

and control. The default protocol for this port is 9600 baud, no parity bit, 8 data bits,

1stop bit, and no flow control (handshaking).

• For information on SIS commands, see Remote Communication and Control on

page111.

• See figure 7 below, to wire the RS-232 connector.

Ground

Tx

Rx

Receive

Transmit

Connected RS-232

Device Pins

SMD 101

Pins

G

Figure 7. RS-232 Connector Wiring

F

Reset button and LED — The reset button is used to return the SMD101 to partial

or complete factory condition. The reset LED provides the status of the reset. The

SMD101 has three reset modes (see SMD101 Rear Panel Reset on the following

page).

G

RJ-45 LAN connector — Connect one end of an RJ-45 cable to the LAN (Ethernet)

connector on the SMD101 (see figure 8). Connect the other end of the RJ-45 cable to

a router or switch to connect the SMD101 to a network.

LAN

ACTLINK

Figure 8. RJ-45 Ethernet Connector

The LEDs on the Ethernet connector indicate the status of the network connection.

• Link LED — This green LED lights when the SMD101 is properly connected to an

active network.

• Act LED — This amber LED blinks in a pattern to indicate the connected network

speed as follows:

• Three blinks — 1 Gbps

• Two blinks — 100 Mbps

• One blink — 10 Mbps

SMD101 • Panels and Cabling 12

SMD101 Rear Panel Reset

The Reset button on the rear panel (see figure 3 on page10) returns the SMD101 to

various modes of operation.

To select different reset modes, use a pointed stylus or small screwdriver to press and hold

the Reset button while the SMD101 is powered, or press and hold the Reset button while

applying power to the SMD101.

ATTENTION:

• Review the reset modes carefully.

• Étudier de près les différents modes de réinitialisation.

• Some reset modes delete all user loaded content and revert the device to default

conﬁguration.

• Certains modes de réinitialisation suppriment la totalité du contenu chargé de

l’utilisateur et remettent l’appareil en mode de conﬁguration par défaut.

NOTES:

• The reset modes close all open IP and Telnet connections and all sockets.

• Each reset mode is a separate reset (not a continuation from mode 1 to mode 5).

• Reset mode 2 is not available for the SMD101.

• The SMD101 can also be reset using the web-based user interface (see Reset

Device on page85).

• For information on resetting the SMD101 using SIS commands, see Absolute

reset on page121 of the Command and Response Tables.

• Further details comparing the reset modes and affected conﬁguration settings

and user content are in the reference section (see SMD101 Reset Summary on

page136).

RESET

RESET RESET

RESET

Release, then immediately

press and release again. Reset

LED ﬂashes, then goes off.

Modes 3

Pr

ess and hold the

Reset

button.

Mode 1

Reset LED ﬂashes once.

Pr

ess and hold for

3 seconds.

Apply power

to the SMD 101.

Release Reset button.

RESET RESET

RESET

Release, then immediately

press and release again. Reset

LED ﬂashes, then goes off.

Modes 4

Reset LED ﬂashes twice.

Pr

ess and hold for

6 seconds.

RESET RESET

RESET

Release, then immediately

press and release again. Reset

LED ﬂashes, then goes off.

Modes 5

Reset LED ﬂashes three

times.

Pr

ess and hold for

9 seconds.

Figure 9. Rear Panel Reset Button

SMD101 • Panels and Cabling 13

Page is loading ...

Extron electronics SMD 101 User manual

This manual is also suitable for

Extron electronics SMD 101 User manual

Related papers

Other documents