Home Styles 4508-95 Assembly Instructions

Brand: Home Styles

Model: 4508-95

Type: Assembly Instructions

PART LIST

HARDWARE LIST

Tools Required For Assembly : Phillips screwdriver

Caster

two lock

two non-lock

4 pcs.

Top

1 pc.

Side Panel

1 pc.

Head Cap Bolt

16 pcs. (+1 extra)

Head Cap Bolt (long)

4 pcs. (+1 extra)

Cross Dowel

4 pcs. (+1 extra)

Hex Wrench

1 pc.

Machine Screw

6 pcs.

Drawer Pull Handle

2 pcs.

Wood Screw (short)

for Drawer Base Part

12 pcs. (+1 extra)

Wood Screw (long)

for Drawer Side Part

16 pcs. (+1 extra)

Cam Lock

4 pcs. (+ 1 extra)

Cam Lock Screw

4 pcs. (+1 extra)

IMPORTANT NOTE

Carefully remove all the parts from the carton and put them I

ndividually on a soft cloth to prevent scratches or other damages

occuring to the parts.

We have taken great care in the design of this product and request that you carefully

and strictly follow our assembly instructions to ensure a completed product as it was designed.

Side Panel

1 pc.

Front Piece

1 pc.

Front Piece

1 pc.

Front Piece

1 pc.

Back Piece

2 pcs.

Back Piece

1 pc.

Back Panel

2 pcs.

Base

1 pc.

Leg

4 pcs.

Door

1 pc.

Door

1 pc.

Wood Screw

for Side Bar

4 pcs. (+1 extra)

Door Pull Handle

2 pcs.

Side Bar

2 pcs.

KD. Drawer

2 pcs.

(Knock-Down Construction,

please refer to the last page of

instructions for steps to complete

assembling drawers)

88 4508 95

Prep & Serve Cart

Small

Hex Wrench

1 pc.

Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319

[email protected]

Revised date : 24Mar2011

Assembly Instructions 2/5

STEP 1

IMPORTANT

Do not tighten up all the screws until each part is properly assembled.

You should keep Hex Wrench in the safe place as you may need to

tighten up the Head Cap Bolts in the future.

Attach Back (D) to

Side Panel (B) at the lower

position with Head Cap Bolts.

Attach Back Piece (H) to

Back Piece (D), then slide

Back Panel (I) into place.

Attach Back Piece (D) to

the unit at upper position.

Tighten the Head Cap Bolts.

Piece

STEP 2

Attach Front Piece (E) and (G)

to the unit with Head Cap Bolts.

Attach Base (J) to the unit

with Head Cap Bolts (long)

and Cross Dowels.

Attach Front Piece (F) to the

unit.

Head Cap Bolt

Head Cap Bolt (long)

Cross Dowel

Upper Position

Lower Position

Assembly Instructions

3/5

STEP 3

Attach Side Panel (C)

to the unit with

Head Cap Bolts,

Head Cap Bolts (long)

and Cross Dowel.

STEP 4

Cross Dowel

Head Cap Bolt (long)

Head Cap Bolt

Locking Caster

Head Cap Bolt

Attach Leg (K) to the unit with Head Cap Bolts.

Attach 4 Casters to the underside of

the legs. First, attach the two Casters

with lock to the front legs to keep the

Cart from moving.

Assembly Instructions

4/5

STEP 5

Turn over Top (A) upside down and place it on a soft, non-scratching surface. Attach Side Bar (L)

to Top (A), using Wood Screws. Put Cam Lock Screws into the pre-drilled holes at Top (A).

(See figure 1)

Place Top (A) onto the unit, using Cam Locks.

Assemble Door Pull Handles to

Door (M) and (N) with

Machine Screws.

(See figure 2)

Attach Door (M) and (N)

to the side panels,

slide the door lift hinges

into the side panel

lift hinges.

(See figure 3)

Slide Drawer (O) to

into place.

(Figure 1)

(Figure 2)

(Figure 3)

Cam Lock Screw

Wood Screw

Cam Lock

Assembly Instructions 5/5

(Figure 1)

(Figure 2)

MAKE SURE ROLLER

IS ON THE BACK

Drawer

Part List

O1.

Front Part

2 pcs.

O5.

Base Part

2 pcs.

O2.

Back Part

2 pcs.

O3.

Side Part

2 pcs.

O4.

Side Part

2 pcs.

* If you are missing any

of these parts, please

contact our DMI

Customer Service

Department at

1-877-831-0319 or fax

us at 1-800-755-2878.

(Figure 3)

(Figure 4)

Attach O1 to O3 and O4, using

a and

the wood screws ,

tighten halfway.

Attach O2 to O3 and O4 using

the wood screws ,

tighten halfway. (See figure 1)

Phillips screwdriver

(4X)

long

Insert the wood screws (6X)

into the pre-drilled holes in O5,

tighten screws. (See figure 3)

short

Tighten all screws used in

drawer assembly.

Attach hardware pulls with

machine screws.

(See figure 4)

Slide O5 into the grooves in O3

and O4. Be sure to push the

O5 all the way forward so

it meets the O1. (See figure 2)

STEP 1

STEP 2

STEP 3

STEP 4

Home Styles 4508-95 Assembly Instructions

Home Styles 4508-95 Assembly Instructions

Home Styles 4508-95 Assembly Instructions

Related papers

Other documents