PART LIST
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
HARDWARE LIST
Head Cap Bolt
13 pcs. (+1 extra)
Hex Wrench
1 pc.
Cam Lock
6 pcs. (+1 extra)
Cam Lock Screw
6 pcs. (+1 extra)
Wood Screw
for Caster and
Gate Leg
20 pcs. (+1 extra)
Adjustable Pin
12 pcs. (+1 extra)
Machine Screw
8 pcs.
Wood Plug
6 pcs.(+2 extra)
A.
Top
1 pc.
B.
Side Panel
1 pc.
D.
Side Panel
1 pc.
E.
Back Panel
2 pcs.
F.
Back Panel
1 pc.
C.
Middle Panel
2 pcs.
H.
Back Stretcher
1 pc.
G.
Back Piece
2 pcs.
I.
Front Piece
1 pc.
T.
Round Arm
1 pc.
M.
Divider
1 pc.
P.
Shelf
2 pcs.
Q.
Shelf
1 pc.
N. & O.
Drawer
2 pcs.
J.
Base
1 pc.
K.
Door
2 pcs.
L.
Door
2 pcs.
U.
Knife Box
1 pc.
(For Drawers, packed in a separate carton)
Caster
two lock
two non-lock
4 pcs.
Tools Required For Assembly : Phillips screwdriver
S.
Handle Arm
2 pcs.
R.
Gate Leg
1 pc.
Drawer
Pull Handle
4 pcs.
88 5023 95C
Kitchen Island with
Breakfast Bar
Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
Small
Hex Wrench
1 pc.
Revised date : 23Mar2011
Head Cap Bolt
J
B
G
G
Assembly Instructions 2/4
STEP 1
STEP 2
IMPORTANT
Do not tighten up all the screws until each part is properly assembled.
You should keep Hex Wrench in the safe place as you may need to
tighten up the Head Cap Bolts in the future.
C
C
Wood Screw
(Figure 1)
Locking Caster
(On Front)
J
Wood Screw
Attach four Casters
to Base (J) with
Wood Screws.
(See figure 1)
Attach Side Panel (B) to Base (J)
with Head Cap Bolts.
Attach Middle Panel (C) and
Back Piece (G) to Base (J).
I
E
E
F
H
M
D
Head Cap Bolt
STEP 3
Slide Back Panel (E) and
(F) to the unit.
Attach Back Stretcher (H)
and Front Piece (I) to the
unit with Head Cap Bolts.
Attach Side Panel (D) and
Divider (M) to the unit with
Head Cap Bolts.
Locking Caster
(On Front)
Assembly
Instructions 3/4
STEP 4
(Figure 2)
Wood Screw
Wood Screw
Attach Gate Leg (R) at the
back of unit with Wood Screws.
(See figure 2)
R
R
STEP 5
Assemble Handle Arm (S) to Side Panel (D) with Head Cap Bolts.
Slide Round Arm (T) into place.
Attach Knife Box (U) to Side Panel (B) with Head Cap Bolts.
Insert Adjustable Pins into side panels and middle panels at the desired level.
Place Shelf (P) and (Q).
U
B
D
T
S
S
P
Q
P
Adjustable Pin
Head Cap Bolt
A
Cam Lock Screw
4/4
STEP 8
Cover up all holes
with Wood Plugs.
A
N
O
K
K
L
L
STEP 7
Assemble Pull Handles to Door (K) and (L)
with Machine Screws. (See figure 4)
Attach Door (K) by inserting the lower Spring Pin into
the hole until it clicks (See figure 5) and then do the
same for the upper Spring Pin.
Do the same process for Door (L).
Slide Drawer (N) and (O) into place.
Put Cam Lock Screws into the
pre-drilled holes at Top (A).
STEP 6
Cam Lock
Machine Screw
Spring Pin
(Figure 3)
(Figure 4)
(Figure 5)
Place Top (A) onto the unit,
using Cam Locks.
(See figure 3)
Cam Lock
Assembly
Instructions
88 5023 95
Drawer (N)
Drawer (O)
Assembly
Instructions
N2, O2.
Back Part
1 pc.for each drawer
N5, O5.
Base Part
1 pc.for each drawer
N3, O3.
Side Part
1 pc.for each drawer
N4, O4.
Side Part
1 pc.for each drawer
N1, O1.
Front Part
1 pc.for each drawer
Assemble the Pull Handle
with Machine Screws on
the Front Part(N1, O1).
(See figure 4)
HARDWARE LIST
MAKE SURE ROLLER
IS ON THE BACK
N1
N1
N1
N1
N5
N5
O1
O1
O1
O1
O5
O5
N2
N2
N2
O2
O2
O2
N3
N3
N3
N3
O3
O3
O3
O3
N5
O5
N4
N4
N4
N4
O4
O4
O4
O4
Machine Screw
4 pcs.
Drawer
Pull Handle
2 pcs.
Wood Screw (short)
for Base Part
12 pcs. (+1 extra)
Wood Screw (long)
for Side Part
16 pcs. (+1 extra)
PART LIST
Using a ,
insert Wood Screws (long) into the
pre-drilled holes as shown, tighten
half way. (See figure 1)
Philips screwdriver
(Figure 1)
Slide the plywood Base Part (N5, O5)
into the grooves on Side Parts (N3, O3)
and (N4, O4). Be sure to push the plywood all
the way forward so it meets the Front Part (N1, O1).
(See figure 2)
(Figure 2)
Insert Wood Screws (short) into the
pre-drilled holes on Base Part (N5, O5),
then tighten all Wood Screws.
(See figure 3)
(Figure 3)
(Figure 4)
* If you are missing any
of these parts, please
contact our DMI
Customer Service
Department at
1-877-831-0319 or fax
us at 1-800-755-2878.
Unfinished Side
/
