Page is loading ...
INSTRUCTIONS FOR USE
InterMetro Industries Corporation
North Washington Street, Wilkes-Barre, PA USA 18705
For Product Information Call: 1-800-992-1776
Visit Our Web Site: www.metro.com
INSTRUCTIONS
FOR USE
High Rise
Shelving System
Hi-Rise Shelving System
INSTRUCTIONS FOR USE
Two People Required to Assemble Unit.
2
1 2 3
4
5
8
6
7
Hi-Rise Shelving System
Single Wall Unit (4 - Post Construction)
Note: Shelving units
mounted against
wall may be double
back-to-back units or
single units. Shelving
units which will not be
against a wall may only
be of the double back-
to-back type.
Square Foot
Plate
x4
Note: For foodservice applications, NSF requires a minimum of
x4
SES Shelf
All Corners
Repeat Step 5
Repeat Step 5
9
Repeat Steps 1-8 and Place Additional
First Level Shelving Units as Shown Below
Additional
Shelving Units
3
11
10
FRONT VIEW
POST CLAMP LOCATIONS
A
FRONT VIEW
B
WALL BRACKET LOCATIONS
WALL SHOWN
FOR REFERENCE
A B
C D
4
12
Hi-Rise Shelving System
Double
Threaded
Stud
13
Install Post
with Double
Threaded Stud
on First Level
Shelving Unit
14
15
Follow Steps 3-8 of Page2 for Assembly Procedure of Installing Shelves at Required Positions
16
Follow Steps 10-11 of Page3 for Installing Post Clamps and Wall Brackets at Required Positions
17
WALL BRACKET AND POST CLAMP LOCATION
5'
5'
5'
5'
All units must have post protection
be installed to prevent any contact
between the shelving units and
various material handling trucks.
NOTE:
The shelving assembly is not to
be used as, or to be support, stock
picking equipment, mezzanines,
catwalks or other auxiliary
equipments.
THIS COMPLETES THE ASSEMBLY OF SINGLE WALL UNIT (4-POST CONSTRUCTION)
HI-RISE SHELVING SYSTEM
Load Rating Plate
Installed 4'-6'
above Floor on
Each Shelving
Row (Both Ends)
5
INSTRUCTIONS FOR USE
Two People Required to Assemble Unit.
Double Unit (4 - Post Construction)
Follow Steps 1-9 of Page2 for
Assembly Procedure of
Shelving Cart and First Level
Shelving Units
1
Follow Steps 12-16 of Page4
for Assembly Procedure of
Installing Shelves at
Required Positions on First
Level Shelving Units
2
3
PLACE SINGLE UNITS BACK TO BACK
Front
Single Unit
Rear
Single Unit
4
Perimeter Posts -
Clamping
Interior Posts -
Clamping
Mounting Holes of
Foot Plates Must
Face Inside
5
Hi-Rise Shelving System
PLACE SINGLE AND DOUBLE UNITS - FRONT VIEW
Single Wall Unit
Double Unit Double Unit
Wall
Shown for
Reference
6
8' Cross Bar
Splice Bar
7
Cross Bar
Single
Wall Unit
Double
Unit
8
9
7/16" Drill Bit
1) Do not allow drill bit to penetrate the post foot and damage
the internal threads of the foot.
2) Cross bars need not be bolted to interior posts.
NOTE:
Interior Posts
10
11
Load Rating
Plate (Typ)
DL
7
12
Splice Bar
Cross Bar
Cross Bar
13
1) When splice kit bolts do not match a post top,
use hex head bolts, lock washer and nut. Four
bolts are required per splice bar.
2) Floor bumpers must be installed to prevent and
contact between the shelving units and various
material handling trucks.
NOTE:
The shelving system as well as the cross bars
should not be subjected to any additional load
such as cross walks, conduit, etc.
14
Cross Bar Splice Bar
Single
Wall Unit
Cross Bar
Double
Unit
TOP VIEW -
LOCATION OF CROSS &
SPLICE BARS
Cross Bar
Splice Bar
Double
Unit
Cross Bar
Splice
Bar
Splice
Bar
DL DL
DL
DL - Drilling
Hole Locations
DL DL
DL
DL
DL DL
DL
DL
DL
DL
DL DL
DL
DL DL
DL
DL
InterMetro Industries Corporation
North Washington Street, Wilkes-Barre, PA USA 18705
For Product Information Call: 1-800-992-1776
Visit Our Web Site: www.metro.com
L01-098 Rev. A
04/2014
* Save this document for future application, load rating and/or safety reference.
Hi-Rise Shelving System
INSTRUCTIONS FOR USE
Two People Required to Assemble Unit.
Single Wall Unit and Double Unit (S-Hook)
1 2
S-Hook
3
x2
4
5
SES Shelf
Support free end of shelf for
ease of assembly.
NOTE:
6
Free End
of Shelf
Follow Step 11 of
Page 3 for Installation
Wall Brackets to the
Unit.
7 8 9
With S- hook
construction there is
only one post to bracket
to the wall. Be careful
not to over- tighten the
hardware as it causes
bracket damage.
NOTE:
SINGLE WALL UNIT DOUBLE UNIT
REFER TO PAGES 2-7 FOR INSTRUCTIONS TO ASSEMBLE SINGLE AND DOUBLE UNITS WITH FIRST
AND SECOND LEVEL SHELVING UNITS.
/