Land Pride ZT360 User manual

Table of Contents

Read the Operator’s Manual entirely. When you

see this symbol, the subsequent instructions and

warnings are serious - follow without exception.

Your life and the lives of others depend on it!

!

Cover photo may show optional equipment

not supplied with standard unit.

ZT360 & ZT372 Accu-Z

®

Zero Turn Mowers

3/16/17

35371

Parts Manual QR Code

357-610M

Operator’s Manual

Table of Contents

ZT360 & ZT372 Accu-Z

®

Zero Turn Mowers 357-610M

3/16/17

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the

preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use

of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this

product at the time of its publication, and may not reflect the product in the future.

Land Pride is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

Table of Contents

Important Safety Information . . . . . . . . . . . . . 1

Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Section 1: Assembly & Set-up . . . . . . . . . . . 10

Uncrating Instructions . . . . . . . . . . . . . . . . . . . . . . 10

Torque Requirements . . . . . . . . . . . . . . . . . . . . . . 10

Control Lever Assembly . . . . . . . . . . . . . . . . . . . . 10

Seat Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Spring Loaded Seat Release Latch . . . . . . . . . . . . 11

Discharge Chute Assembly . . . . . . . . . . . . . . . . . . 11

Folding ROPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Electrical Cable Connection . . . . . . . . . . . . . . . . . 12

Engine Preparations . . . . . . . . . . . . . . . . . . . . . . . 13

Section 2: Operating Procedures . . . . . . . . . 14

Mower Features . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Operating Checklist . . . . . . . . . . . . . . . . . . . . . . . . 15

Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Accessing Area Beneath Seat Platform . . . . . . . . . 16

Accessing Area Beneath Floor Pan . . . . . . . . . . . . 17

Moving Mower with Stalled Engine . . . . . . . . . . . . 17

Transport Height . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Cutting Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Clearing Obstacles . . . . . . . . . . . . . . . . . . . . . . . . 18

Engine Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Engine Shut-Down Sequence . . . . . . . . . . . . . . . . 19

Safety Start Interlock System . . . . . . . . . . . . . . . . 19

Driving the Mower . . . . . . . . . . . . . . . . . . . . . . . . . 19

Towing Using The Rear Hitch . . . . . . . . . . . . . . . . 21

Safe Operating Instructions . . . . . . . . . . . . . . . . . . 21

Good Operating Practices . . . . . . . . . . . . . . . . . . . 23

General Operating Information . . . . . . . . . . . . . . . 23

Section 3: Adjustments . . . . . . . . . . . . . . . . . 24

Torque Requirements . . . . . . . . . . . . . . . . . . . . . . 24

Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Park Brake Adjustment . . . . . . . . . . . . . . . . . . . . . 24

Seat Reach Adjustment . . . . . . . . . . . . . . . . . . . . . 25

Suspension Seat Weight Adjustment . . . . . . . . . . 25

Additional Seat Suspension . . . . . . . . . . . . . . . . . . 25

Deck Lift Pedal Adjustment . . . . . . . . . . . . . . . . . . 26

Steering Adjustments . . . . . . . . . . . . . . . . . . . . . . 26

Lower Control Lever . . . . . . . . . . . . . . . . . . . . . . 26

Upper Control Lever . . . . . . . . . . . . . . . . . . . . . . 27

Belt Tensioning . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Deck Leveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Deck Lift Assist Springs . . . . . . . . . . . . . . . . . . . . . 30

Anti-Scalp Rollers . . . . . . . . . . . . . . . . . . . . . . . . . 30

Front Axle Pivot . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Section 4: Options & Accessories . . . . . . . . 32

Folding Soft Top Canopy . . . . . . . . . . . . . . . . . . . . 32

Head Light Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Safety Flashing Light & SMV Sign Kit . . . . . . . . . . 32

Lift Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Mulching Kit & Blades . . . . . . . . . . . . . . . . . . . . . . 33

Rear Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Inductive Tachometer . . . . . . . . . . . . . . . . . . . . . . 33

Section 5: Maintenance & Lubrication . . . . . 34

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Maintenance Safety . . . . . . . . . . . . . . . . . . . . . . . . 34

Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . 35

Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Torque Requirements . . . . . . . . . . . . . . . . . . . . . . 36

Electrical System . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Belt Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Hydrostatic Drive System . . . . . . . . . . . . . . . . . . . 40

Transaxle Oil Check & Filling . . . . . . . . . . . . . . . . . 40

Transaxle Oil & Filter Change . . . . . . . . . . . . . . . . 41

Transaxle Purging Procedures . . . . . . . . . . . . . . . 41

Fuel System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Evaporative Emission Control System . . . . . . . . . . 43

Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Drain Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

General Engine Maintenance . . . . . . . . . . . . . . . . 43

Engine Oil & Oil Filter . . . . . . . . . . . . . . . . . . . . . . 44

Engine Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Engine Air Filter Handling . . . . . . . . . . . . . . . . . . . 46

Mower Blade Maintenance . . . . . . . . . . . . . . . . . . 47

End of Season & Long Term Storage . . . . . . . . . . 49

New Season Preparation . . . . . . . . . . . . . . . . . . . . 49

Lubrication Points . . . . . . . . . . . . . . . . . . . . . . . . . 50

Section 6: Specifications & Capacities . . . . . 53

Section 7: Features & Benefits . . . . . . . . . . . 56

Section 8: Troubleshooting . . . . . . . . . . . . . . 58

Section 9: Torque & Tire Inflation Charts . . . 60

Section 10: Warranty . . . . . . . . . . . . . . . . . . . 62

1

Important Safety Information

ZT360 & ZT372 Accu-Z

®

Zero Turn Mowers 357-610M

Table of Contents

3/16/17

Important Safety Information



These are common practices that may or may not be applicable to the products described in

this manual.

Safety at All Times

Thoroughly read and understand the

instructions given in this manual

before operation. Refer to the “Safety

Label” section, read all instructions

noted on them.

Do not allow anyone to operate this

equipment who has not fully read

and comprehended this manual and

who has not been properly trained in

the safe operation of the equipment.

 Operator should be familiar with all

functions of the mower.

 The operator must not use drugs or

alcohol as they can change the

alertness or coordination of that

person while operating equipment.

The operator should, if taking over-

the-counter drugs, seek medical

advice on whether he/she can safely

operate the equipment.

 Operate mower from the driver’s seat

only.

 Make sure all guards and shields are

in place and secured before

operating the mower.

 Do not leave mower unattended with

engine running.

 Dismounting from a moving mower

can cause serious injury or death.

 Do not allow anyone to stand

between mower and equipment

while backing up to hitch mower to

the equipment.

 Keep hands, feet, and clothing away

from power-driven parts.

 Wear snug fitting clothing to avoid

entanglement with moving parts.

 Watch out for wires, rocks trees, etc.,

when using the mower. Make sure

all persons are clear of working area.

 Do not carry passengers on the

mower at any time.

 Turning mower too tight may cause

hitched machinery to ride up on

wheels. This could result in injury or

equipment damage.

Look For The Safety Alert Symbol

The SAFETY ALERT SYMBOL indicates there is a

potential hazard to personal safety involved and extra

safety precaution must be taken. When you see this

symbol, be alert and carefully read the message that

follows it. In addition to design and configuration of

equipment, hazard control and accident prevention

are dependent upon the awareness, concern,

prudence, and proper training of personnel involved

in the operation, transport, maintenance, and storage

of equipment.

Be Aware of

Signal Words

A Signal word designates a degree or

level of hazard seriousness. The

signal words are:

Indicates an imminently hazardous

situation which, if not avoided, will

result in death or serious injury. This

signal word is limited to the most

extreme situations, typically for

machine components that, for

functional purposes, cannot be

guarded.

!

DANGER

Indicates a potentially hazardous

situation which, if not avoided, could

result in death or serious injury, and

includes hazards that are exposed

when guards are removed. It may also

be used to alert against unsafe

practices.

Indicates a potentially hazardous

situation which, if not avoided, may

result in minor or moderate injury. It

may also be used to alert against

unsafe practices.

!

WARNING

!

CAUTION

For Your Protection

 Thoroughly read and understand

the “Safety Label” section, read all

instructions noted on them.

Shutdown and Storage

 Put mower in park, turn off engine,

and remove key.

 Store mower in an area where

children normally do not play.

OFF

R

E

M

OV

E

ZT360 & ZT372

Parts Manual

Kawasaki FX850V

Owner’s Manual

Manual QR Locator

The QR (Quick Reference) codes on the cover and below will take you to the Parts

Manual for this equipment. Download the appropriate App on your camera phone,

open the App, point your phone on the QR code, and take a picture.

Dealer QR Locator

The QR code below will link you to

available dealers for Land Pride

products.

!

2

Important Safety Information

ZT360 & ZT372 Accu-Z

®

Zero Turn Mowers 357-610M

Table of Contents

3/16/17

These are common practices that may or may not be applicable to the products described in

this manual.

Keep Riders Off Mowers

 Riders obstruct the operator’s

view, they could be struck by

foreign objects or thrown from the

machine.

 Never allow children under 16

years of age to operate

equipment.

Use Seat Belt and ROPS

 Operate only mowers equipped

with Roll-Over Protective

Structure (ROPS) and seat belt.

 Fasten seat belt snugly and

securely to help protect operator

from being thrown, crushed, or

severely injured if a rollover

occurs; and from falling off the

mower and being ran over. Not

using the seat belt & ROPS can

result in serious injury or death.

 LOW STRUCTURES CAN FLIP

MOWER OVER BACKWARDS.

Lower ROPS to drive under low

structures such as tree limbs and

doorways.

Prepare for Emergencies

 Be prepared if a fire starts.

 Keep a first aid kit and fire

extinguisher handy.

 Keep emergency numbers for

doctor, ambulance, hospital, and

fire department near phone.

911

Tire Safety

 Tire changing can be dangerous

and should be preformed by

trained personnel using the

correct tools and equipment.

 When inflating tires, use a clip-on

chuck and extension hose long

enough to allow you to stand to

one side and NOT in front of or

over the tire assembly. Use a

safety cage if available.

 When removing and installing

wheels, use wheel handling

equipment adequate for the

weight involved.

Wear

Protective Equipment

 Wear protective clothing and

equipment appropriate for the job

such as safety shoes, safety

glasses, hard hat, and ear plugs.

 Clothing should fit snug without

fringes and pull strings to avoid

entanglement with moving parts.

 Prolonged exposure to loud noise

can cause hearing impairment or

hearing loss. Wear suitable

hearing protection such as

earmuffs or earplugs.

 Operating equipment safely

requires the operator’s full

attention. Avoid wearing radio

headphones while operating

machinery.

Avoid High

Pressure Fluids Hazard

 Escaping fluid under pressure can

penetrate the skin causing serious

injury.

 Avoid the hazard by relieving

pressure before disconnecting

hydraulic lines or performing work

on the system.

 Make sure all hydraulic fluid

connections are tight and all

hydraulic hoses and lines are in

good condition before applying

pressure to the system.

 Use a piece of paper or

cardboard, NOT BODY PARTS, to

check for suspected leaks.

 Wear protective gloves and safety

glasses or goggles when working

with hydraulic systems.

 DO NOT DELAY. If an accident

occurs, see a doctor familiar with

this type of injury immediately.

Any fluid injected into the skin

or eyes must be

treated within a few

hours or gangrene

may result.

3

Important Safety Information

ZT360 & ZT372 Accu-Z

®

Zero Turn Mowers 357-610M

Table of Contents

3/16/17

These are common practices that may or may not be applicable to the products described in

this manual.

Practice Safe Maintenance

 Understand safe and correct maintenance

procedures before doing work. Use proper

tools and equipment, refer to Operator’s

Manual for additional information.

 Work in a clean dry area.

 Never run mower in an enclosed area. Mower

engine exhaust emits carbon monoxide and

other poisonous gases.

 Keep hands, feet, body extremities, and

clothing away from all moving parts such as

pulleys, belts, cutting blades, engine, and

wheels. Don’t wear loose fitting clothing while

operating or servicing mower.

 Put mower in neutral, set park brake,

disengage blades, turn off engine, remove

switch key and wait for all moving components

to stop before performing maintenance on the

mower.

 Repairs or maintenance requiring engine

power should be performed by trained

personnel only.

 Allow mower to cool completely before

performing maintenance.

 Disconnect battery ground cable (-) before

servicing or adjusting electrical systems or

welding on the mower.

 Observe safe fuel handling precautions. Fuel is

flammable and vapors are very explosive.

 Do not grease or oil mower while in operation.

 Inspect all parts. Make sure parts are in good

condition and installed properly.

 Remove buildup of grease, oil, or debris.

 Replace all guards and floor pan before putting

mower back into service.

 Remove all tools and unused parts from mower

before operation.

4

Important Safety Information

ZT360 & ZT372 Accu-Z

®

Zero Turn Mowers 357-610M

Table of Contents

3/16/17

Safety Labels

Your Zero Turn Mower comes equipped with all safety labels in

place. They were designed to help you safely operate your

implement. Read and follow their directions.

1. Keep all safety labels clean and legible.

2. Refer to this section for proper label placement. Replace

all damaged or missing labels. Order new labels from your

nearest Land Pride dealer. To find your nearest dealer,

visit our dealer locator at www.landpride.com.

3. Some new equipment installed during repair requires

safety labels to be affixed to the replaced component as

specified by Land Pride. When ordering new components

make sure the correct safety labels are included in the

request.

4. Refer to this section for proper label placement.

To install new labels:

a. Clean surface area where label is to be placed.

b. Spray soapy water onto the cleaned area.

c. Peel backing from label and press label firmly onto the

surface.

d. Squeeze out air bubbles with edge of a credit card or

with a similar type of straight edge.

838-829C

Caution: Do Not Power Wash

838-303C

Danger: Battery

(Beneath Seat Platform)

818-543C

Danger: Guard Missing

(Beneath Seat Platform)

35372

35373

5

Important Safety Information

ZT360 & ZT372 Accu-Z

®

Zero Turn Mowers 357-610M

Table of Contents

3/16/17

838-307C

Warning: Moving Parts

35374

35373

838-310C

Warning: General

838-815C

Warning: Rollover Hazard

6

Important Safety Information

ZT360 & ZT372 Accu-Z

®

Zero Turn Mowers 357-610M

Table of Contents

3/16/17

838-833C

Warning: Fuel (Imbedded in Fuel Tank)

838-306C

Warning: Do not operator without deflector

838-308C

Warning: Rotating Blade Hazard

35373

35375

35374

840-335C

Anti-slip step pad

7

Important Safety Information

ZT360 & ZT372 Accu-Z

®

Zero Turn Mowers 357-610M

Table of Contents

3/16/17

838-444C

Danger: Muffler Hot

(Both Sides of Engine)

Beneath Pulley Shields

Beneath Floor Pan

35406

35374

35373

33763

818-543C

Danger: Guard Missing

3 - Places On The Deck

1 - Place Beneath Floor Pan

848-268C

Warning: Safe Operating Instructions

8

Introduction

ZT360 & ZT372 Accu-Z

®

Zero Turn Mowers 357-610M

Table of Contents

3/16/17

Introduction

Terminology

“Right” or “Left” as used in this manual is determined by

facing forward while sitting in the operator seat unless

otherwise stated.

Definitions

Owner Assistance

The Online Warranty Registration should be completed

by the dealer at the time of purchase. This information is

necessary to provide you with quality customer service.

The parts on your Zero Turn Mower have been specially

designed by Land Pride and should only be replaced with

genuine Land Pride parts. Contact a Land Pride dealer if

customer service or repair parts are required. Your Land

Pride dealer has trained personnel, repair parts, and

equipment needed to service the implement.

Serial Number

Model No. _____________Serial No. ______________

For quick reference and prompt service, record model

number and serial number in the spaces provided above

and again on warranty page 62. Always provide model

number and serial number when ordering parts and in all

correspondences with your Land Pride dealer. Refer to

Figure 1 on page 9 for location of your serial number

plate.

IMPORTANT: A special point of information related

to the following topic. Land Pride’s intention is this

information must be read & noted before continuing.

NOTE: A special point of information that the

operator should be aware of before continuing.

For parts and service to your mower engine, contact

your nearest engine dealer or call Customer Service

Hotline provided below.

Owner’s Manual Part No.

Kawasaki - 27 HP. . . . . . 99920-2232

Service Manual Part No.

Kawasaki - 27 HP. . . . . . 99924-2089-01

Service Hotline Phone No.

Kawasaki . . . . . . . . . . . . 1-800-433-5640

Land Pride welcomes you to the growing family of new

product owners.

This mower has been designed with care and built by

skilled workers using quality materials. Proper assembly,

maintenance, and safe operating practices will help you

get years of satisfactory use from this machine.

Application

The Accu-Z ZT360 and ZT372 Zero Turn Mowers from

Land Pride are commercial duty mowers. They are very

maneuverable, extremely comfortable, highly productive,

and come in cutting configurations designed to meet the

needs of even the most discriminating owners and

custom operators. This makes the ZT3 Series one of the

premier choices of grass maintenance machines for

ranchers, farmers, large estate owners, cemeteries,

municipalities, campuses, and landscape maintenance

contractors.

The ZT3 Series mowers come equipped with a choice of

either 60" or 72" cutting decks with high blade tip speeds

ranging from 18,350 feet per minute on the 60" deck to

19,300 feet per minute on the 72" deck. The decks adjust

from 1" to 5" cutting height in 1/4" increments. The 60"

deck meets the needs of customers who mow in tighter

areas around obstacles or want to maintain a lower

cutting height over undulating terrain. The more

productive 72" cutting deck will meet the needs of

customers with more level and open areas to cut and just

want to get the mowing job done faster. The Accu-Z is

supplied with 27 hp Kawasaki air cooled engines for

proven performance, power, and reliability.

Customers living in areas with hills or warmer and wetter

climates will typically want to employ the floating axle

capability for enhanced traction capability and a

smoother ride.Twin-lever hydrostatic steering will enable

the Land Pride Accu-Z Zero Turn Mowers to turn within

their overall length. Couple this outstanding

maneuverability with a maximum 12 mph mowing speed

and low center of gravity and you’ve got mowing

capability that’s fast, safe, comfortable, and easy to

transport that will meet your commercial needs.

See “Specifications & Capacities” on page 53 and

“Features & Benefits” on page 56 for additional

information and performance enhancing options.

Using This Manual

•

This Operator’s Manual is designed to help familiarize

the operator with safety, assembly, operation,

adjustments, troubleshooting, and maintenance. Read

this manual and follow the recommendations to help

ensure safe and efficient operation.

• The information contained within this manual was

current at the time of printing. Some parts may change

slightly to assure you of the best performance.

• To order a new Operator’s or Parts Manual, contact

your authorized dealer. Manuals can also be

downloaded, free-of-charge, from our website at

www.landpride.com.

9

Introduction

ZT360 & ZT372 Accu-Z

®

Zero Turn Mowers 357-610M

Table of Contents

3/16/17

Serial Number Plate Location

Figure 1

35371

Further Assistance

Your dealer wants you to be satisfied with your new

mower. If for any reason you do not understand any part

of this manual or are not satisfied with the service

received, the following actions are suggested:

1. Discuss the matter with your dealership service

manager making sure that person is aware of any

problems you may have and has had the opportunity

to assist you.

2. If you are still not satisfied, seek out the owner or

general manager of the dealership, explain the

problem, and request assistance.

3. For further assistance write to:

Land Pride Service Department

1525 East North Street

P.O. Box 5060

Salina, Ks. 67402-5060

E-mail address

lpservicedept@landpride.com

10

Section 1: Assembly & Set-up

ZT360 & ZT372 Accu-Z

®

Zero Turn Mowers 357-610M

Table of Contents

3/16/17

Section 1: Assembly & Set-up

Uncrating Instructions

The shipping crate is assembled together with nails. It

can be disassembled by prying or cutting the lumber

apart. Be careful not to scratch, dent, or cut the mower

and seat while uncrating. It is best if two people are

present while disassembling the crate.

1. Remove end and side panels from shipping crate.

2. Gently lift mower from crate floor with a hoist or other

suitable lifting device.

Torque Requirements

Refer to “Torque Values Chart” on page 60 to

determine correct torque values for common bolts. See

“Additional Torque Values” at bottom of chart for

exceptions to standard torque values.

Control Lever Assembly

Refer to Figure 1-1:

Control levers (#2 & #3) may be shipped from the factory

rotated down and secured with control lever mounting

bolts (#7A). Skip to “Seat Assembly” below if rotated up.

1. Loosen bolt (#7A) on upper right control lever (#3).

2. Remove bolt (#7B) from lower right control lever (#4).

3. Rotate control lever up until slot in upper control lever

aligns with hole in lower control lever.

4. Reinstall 3/8"-16 1 1/2" GR5 hex head bolt (#7B) and

3/8" hex flange lock nut (#9).

5. Repeat steps 1 to 4 for left control lever (#2).

6. Align control lever handles with each other and

tighten bolts (#7A & #7B) to the correct torque.

Seat Assembly

Refer to Figure 1-1:

Depending on seat option, the mower may be shipped

with seat attached. If not, the seat (#1) is shipped factory

mounted to the hinged seat platform (#4) and attached to

the shipping crate with lag bolts. It may have already

been removed in step 1 under “Uncrating Instructions”.

If not, remove it now.

1. Spread control levers (#2 & #3) fully apart before

attaching seat platform to mower frame.

IMPORTANT: Do not drive mower off the crate floor,

as this can bend or break components underneath

the mower, especially the transaxles. Lift mower off

the crate floor with a hoist or other suitable lifting

device. Be careful not to damage the paint and seat

while lifting the unit off the crate floor.

NOTE: To make final control lever adjustments,

see “Upper Control Lever” on page 27.

IMPORTANT: Be careful not to cut seat material

when removing protective packing around the seat.

Cutting seat material will void its warranty.

Control Lever & Seat Assembly (Standard Seat Shown)

Figure 1-1

35401

2. Insert flange bushing (#10) into holes “A” as shown.

3. Attach seat platform (#6) with 3/8"-16 shoulder

bolts (#8) and hex flange lock nuts (#9) as shown.

Tighten lock nuts to the correct torque.

4. Connect mower switch wires to the seat switch

located under the seat.

5. Zip tie wire for seat switch to seat pan using

holes “B”.

6. Hinge seat platform down. The platform will catch

automatically under the spring loaded latch (#5).

7. Being careful not to cut seat material, remove

protective packing around seat.

8. See “Seat Reach Adjustment” on page 25 for

positioning the seat forward and rearward.

11

Section 1: Assembly & Set-up

ZT360 & ZT372 Accu-Z

®

Zero Turn Mowers 357-610M

Table of Contents

3/16/17

Spring Loaded Seat Release Latch

Refer to Figure 1-2:

!

WARNING

The seat pan should always be latched in the down position

before starting mower. Not doing so can cause bodily injury.

When seat is shipped attached to the mower, the spring

loaded seat release latch (#3) is bolted shut for shipping

purposes only. Bolt (#1) and nut (#2) should be removed

during dealer set-up.

1. Remove hex flange nut (#2) and carriage bolt (#1)

from seat release latch (#3).

2. Discard carriage bolt and hex flange nut.

3. See “Accessing Area Beneath Seat Platform” on

page 16 for special step by step instructions on

accessing the area below the seat platform.

Seat Release Latch

Figure 1-2

35545

Discharge Chute Assembly

Refer to Figure 1-3:

The Zero Turn Mower is shipped with carriage bolts (#2)

and hex flange locknuts (#3) attached to the deck in the

location shown. Remove carriage bolts from deck and

attach discharge chute to the deck as follows:

1. Attach discharge chute (#1) to the deck by inserting

3/8"-16 x 1" GR5 carriage bolts (#2) up through deck

bottom as shown.

2. Secure with hex flange locknuts (#3). Tighten lock

nuts to correct torque.

Discharge Chute Assembly

Figure 1-3

33765

12

Section 1: Assembly & Set-up

ZT360 & ZT372 Accu-Z

®

Zero Turn Mowers 357-610M

Table of Contents

3/16/17

Folding ROPS

!

DANGER

Low structures can make contact with the ROPS and flip the

mower over backwards. Fold ROPS down when driving under

low structures such as tree limbs and doorways.

!

CAUTION

Keep hands and other body extremities away from hinged

pinch points while folding and unfolding ROPS.

The ROPS (Roll Over Protection System) is shipped

factory installed and folded down.

ROPS Unfolding Instructions

Refer to Figure 1-4:

ROPS locking knobs (#1) are shipped in an attached

parts bag.

1. Remove hitch pins (#2) and rotate upper ROPS

frame (#3) up to position shown.

2. Reinsert hitch pins (#2) and secure with attached

hairpins.

3. Install locking knobs (#1) and hand tighten.

Folding ROPS Bar Assembly

Figure 1-4

33824

Electrical Cable Connection

Refer to Figure 1-5:

!

WARNING

Incorrect battery cable connections can damage the mower’s

electrical system and cause battery cables to spark. Sparks

around a battery can result in a battery gas explosion and

personal injury.

• Always disconnect negative (black) cable from battery

before disconnecting positive (red) cable.

• Always reconnect positive (red) cable to the battery’s

positive (+) post before reconnecting negative (black)

cable to the battery’s negative (-) post.

!

WARNING

Keep battery terminals from touching any metal mower parts

when removing or installing battery. Do not allow metal tools

to short between battery terminals and metal mower parts.

Shorts caused by battery terminals or metal tools touching

metal mower components can cause sparks. Sparks can cause

a battery gas explosion which can result in personal injury.

Attach black battery cable (#3) to the negative post with

1/4"-20 x 3/4" GR5 serrated screw (#1) and hex whiz

nut (#2). Tighten whiz nut to the correct torque.

Connecting Black Cable To Negative Battery Post

Figure 1-5

IMPORTANT: The black negative battery cable is

disconnected before leaving the factory and is to be

disconnected after initial dealer set-up to prevent

battery discharge while sitting on the dealer lot.

Negative Post

Black Battery

Cable (-)

Red Battery

Cable (+)

35377

Positive Post

13

Section 1: Assembly & Set-up

ZT360 & ZT372 Accu-Z

®

Zero Turn Mowers 357-610M

Table of Contents

3/16/17

Engine Preparations

1. Check engine oil level at the dipstick. Add oil if below

full mark. Do not overfill. Refer to Engine Operator’s

Manual for oil recommendation and to “Engine Oil &

Oil Filter” on page 44 in this manual.

2. First read instructions under “Fuel System” on page

42 before continuing.

Set-up for Customer:

Add a small amount of gasoline to one of the fuel

tanks. Dealer to supply gasoline.

Set-up for display:

Add a small amount of gasoline and fuel stabilizer to

one of the fuel tanks. Dealer to supply gasoline and

fuel stabilizer.

3. Switch fuel tank valve to the fuel tank with gasoline.

See balloon #22, “Left/Right Fuel Tank Select

Switch” on page 14.

NOTE: Mowers are shipped from the factory

without fuel in the fuel tanks.

14

Section 2: Operating Procedures

ZT360 & ZT372 Accu-Z

®

Zero Turn Mowers 357-610M

Table of Contents

3/16/17

Mower Features

Refer to Figure 2-1:

Your Zero Turn Mower is designed with innovative and

state-of-the-art features. Knowing the location and how

these features work will make handling your mower more

comfortable. Below is a list of major features to be

reviewed in this section. Not all features listed will be

reviewed.

ZST Mower Features (ZT360 Shown)

Figure 2-1

35378

26

19

25

18

11

13

17

10

21

23

13

14

16

3

30

24

5

15

3

6

7

2

8

7

5

6

32

4

29

31

12

22

20

28

27

9

1

34

33

1. Rear Bumper, Hitch & Engine Guard

2. Battery (Located under seat platform)

3. Fuel Tanks

4. Hydraulic Oil Expansion Tank Caps

5. Drive Wheels

6. Tethered Fuel Caps

7. Fuel Vent Valves

8. Cup Holders

9. Park Brake Lever

10. Control Levers

11. Left Deck Spindle Cover (Guard)

12. 60" or 72" Mower Deck

13. Anti-Scalp Wheels

14. Floor Pan (Guard)

15. Caster Wheels

16. Adjustable Deck Lift Pedal

17. Deck Height Gauge Bar

18. Right Deck Spindle Cover (Guard)

19. Deck Height Indicator

20. Operator Seat

21. Seat Platform (Guard)

22. Left/Right Fuel Tank Select Switch

23. Seat Release Latch (Behind Seat)

24. Operator Pressure Switch

(Located under seat)

25. Discharge Chute (Guard)

26. Control Panel

(See Figure 2-2 on page 15)

27. Oil Fill / Dip Stick

28. Oil Filter

29. Gas Engine

30. Engine Air filter

31. Engine Exhaust Muffler

32. Front Floating Axle

33. Floating Axle Locks (Bent Pins

located under floor pan)

34. ROPS, Roll Over Protective Structure

Section 2: Operating Procedures

15

Section 2: Operating Procedures

ZT360 & ZT372 Accu-Z

®

Zero Turn Mowers 357-610M

Table of Contents

3/16/17

Operating Checklist

Hazard control and accident prevention are dependent

upon awareness, concern, prudence and proper training

involved in operation, transport, maintenance, and

storage of the riding mower. Therefore, it is absolutely

essential that no one operates the mower without first

having read, fully understood, and become totally familiar

with the Operator’s Manual. Make sure the operator has

paid particular attention to:

• Important Safety Information, page 1

• Section 1: Assembly & Set-up, page 10

• Section 2: Operating Procedures, page 14

• Section 3: Adjustments, page 24

• Section 5: Maintenance & Lubrication, page 34

The following Operating Checklist should be performed

before operating your mower:

Control Panel

Refer to Figure 2-2:

!

WARNING

Do not operate mower while smoking.

Ignition Switch

A three position ignition switch: off, run, and start is

provided. With key inserted, rotate it clockwise to START

position; release key when engine starts and switch will

automatically return to RUN position. Turn key

counterclockwise to OFF position to stop engine.

Throttle

A cable is linked from engine to throttle for controlling

engine speed. Move throttle lever toward fast position to

increase engine rpm and toward slow position to

decrease rpm. Always travel and cut grass with throttle

set at full engine rpm speed. Decrease travel speed by

Operating Checklist



Check Ref.

Carefully read and follow all safety rules.

Refer to “Important Safety Information”.

Page 1

Make sure all guards and shields are in place.

Refer to “Mower Features”.

Page 14

Make all required adjustments.

Refer to “Section 3: Adjustments”.

Page 24

Read and follow all operating procedures.

Refer to “Section 2: Operating Procedures”.

Page 14

Check mower safety start interlock system daily

prior to operation.

Page 19

Perform all maintenance and lubrications.

Refer to “Section 5: Maintenance & Lubrication”.

Page 34

Make sure there are no hydraulic leaks on the unit.

Refer to “Avoid High Pressure Fluids Hazard”.

Page 2

Check blade for nicks and sharpness.

Refer to “Mower Blade Maintenance”.

Page 47

Check mower initially and periodically for loose

bolts and pins. Refer to “Torque Values Chart”.

Page 60

pulling back on the control levers. Reduce engine rpm

only when mower is not traveling and just before

engaging the cutting blades.

Control Panel

Figure 2-2

Choke

A cable is linked from the choke control knob to the

engine for choking the engine during starting. Pull up on

knob to turn choke (ON). Push down on knob once

engine is running to shut choke (OFF).

Blade Engagement Switch

The blade engagement switch engages the deck blades.

Pull switch up (ON) to engage blades and push switch

down (OFF) to disengage blades.

Hour Meter

The hour meter registers 1/10 hour increments up to

9,999.9 total hours. The meter is connected to the ignition

switch and records accumulative time only while the

engine is running. Remove plastic film covering over hour

meter before placing mower into service.

Engine Light

The engine light, when lit, indicates low oil pressure. This

light will come on when starting engine and should go off

soon after engine is started. Shut engine off immediately

if light comes on during normal operation and investigate

cause before putting mower back into service.

IMPORTANT: Always operate throttle at full engine

rpm while traveling and cutting grass. Operating

engine at a slow rpm may overheat engine and

transaxles.

33178

Hour Meter

Throttle

Blade Engagement Clutch

Choke

Ignition Switch

Engine Light

IMPORTANT: DO NOT operate mower with choke

on.

IMPORTANT: With mower stopped and engine at

half throttle, engage cutting blades. Increase throttle

to full engine speed and then operate control levers

to move mower. Clutch, belts and/or deck may be

damaged if blades are engaged at full engine speed.

16

Section 2: Operating Procedures

ZT360 & ZT372 Accu-Z

®

Zero Turn Mowers 357-610M

Table of Contents

3/16/17

Park Brake

Refer to Figure 2-3 & Figure 2-4:

The park brake lever is linked to the wheel motors. The

rear wheels are kept from turning when park brake lever

is pulled back or to the (ON) position. Push lever forward

to (OFF) position to release park brakes.

Mower engine will stop running if park brake lever is set to

(ON) before spreading both control levers (OUT) or if one

or both control levers are moved (IN) before moving park

brake lever to (OFF).

Control Levers

Refer to Figure 2-3 & Figure 2-4:

The control levers are used to steer, accelerate,

decelerate, stop, and change direction of travel.

Always move both control levers to neutral position and

then spread them fully (OUT) before setting park brake

lever to the (ON) position. Set park brake to the (ON)

position. Always leave park brake and control levers in

this position until ready to start traveling. Move park

brake to the (OFF) position before pulling control levers

(IN). Start moving by moving control levers either forward

or rearward from neutral position.

See “Driving the Mower” on page 19 for a detailed

description of operating the control levers.

Accessing Area Beneath Seat

Platform

Refer to Figure 2-5:

The compartment below the seat platform (#2) is where

the control lever linkages, hydrostatic drives, belts,

battery, and fuses are located. The seat is secured over

this compartment with a spring loaded seat latch (#1).

!

WARNING

The seat pan should always be latched in the down position

before starting mower. Not doing so can cause bodily injury.

Refer to Figure 2-3:

1. Park unit on a flat level surface. Stop engine and

remove ignition key. Make sure blade engagement

switch is in the down (OFF) position. Spread

control levers fully apart and set park brake.

Refer to Figure 2-5:

2. Pull seat latch (#1) to the left & lift seat platform (#2)

up to raise seat for viewing compartment below.

3. Close seat platform by lowering platform down until

seat latch catches on the seat platform. See “Seat

Reach Adjustment” on page 25 for positioning seat

forward and rearward.

NOTE: A carriage bolt may be inserted through

square hole in latch (#1) and secured with a nut.

Torque nut tight to prevent people from easily lifting

the seat platform while mower is operating.

Control Levers Fully OUT (In Park Position)

Figure 2-3

Control Levers Fully IN (In Neutral Position)

Figure 2-4

Seat Release Latch

Figure 2-5

35403

Park Brake (ON)

Both Control Levers Must Be Spread Fully (OUT)

Before Park Brake Is Engaged (ON).

Blade Engagement Switch (OFF)

35402

Control Levers (IN)

Neutral Operating Position

Neutral Slot

Park Brake (OFF)

33770

1

2

17

Section 2: Operating Procedures

ZT360 & ZT372 Accu-Z

®

Zero Turn Mowers 357-610M

Table of Contents

3/16/17

Accessing Area Beneath Floor Pan

Refer to Figure 5-2:

Deck components located under the floor pan (#2) can

be accessed easily by raising the floor pan up.

!

WARNING

The floor pan must always be in the down position before

starting the mower. Not doing so can cause bodily injury.

1. Park unit on a flat, level surface. Stop engine and

remove ignition key. Make sure blade engagement

switch is in the down (OFF) position, control levers

are spread fully apart, and park brake is pulled back

to the (ON) position.

2. Rotate deck lift pedal (#1) rearward as shown.

3. Using hand holds in floor pan, raise floor pan (#2) up

until resting on it front face as shown.

4. When finished working, lower floor pan down using

hand holds and rotate deck lift pedal (#1) forward to

normal operating position.

Moving Mower with Stalled Engine

Refer to Figure 2-7:

Each hydro-drive is equipped with a bypass valve for the

purpose of moving the mower when engine is inoperable.

Both bypass valves are located under the hydro-drive

cooling fan. They face toward the center of the mower in

the location shown.

1. Rotate bypass valve slot to vertical (Bypass) position

to allow drive wheel to rotate freely.

2. Repeat step 1 for the other hydro-drive.

3. Position both control levers in neutral with handles

fully apart.

4. Release park brake lever.

5. Manually move mower by hand or with a winch.

PB

IMPORTANT: Do not tow mower. Move it by hand or

use a winch and load it onto a trailer. Make certain

mower is properly secured to the trailer and its park

brake is locked.

IMPORTANT: Following repairs, always make

certain both bypass valves are rotated horizontal

(run position) before operating mower.

Hinge Floor Pan

Figure 2-6

Bypass Valve (Operating or Run Position Shown)

Figure 2-7

Hand Holds

35379

33771

Bypass Valve

18

Section 2: Operating Procedures

ZT360 & ZT372 Accu-Z

®

Zero Turn Mowers 357-610M

Table of Contents

3/16/17

Transport Height

Refer to Figure 2-8:

!

CAUTION

Disengage mower blades before changing deck height! Deck

stop pin could get into rotating parts if dropped.

1. Disengage blades, move control levers fully out, and

set park brake.

2. Push forward on deck lift pedal (#1) with your right

foot to raise deck fully up until transport lock (#2)

catches and holds deck up. Release deck lift pedal.

Cutting Height

Refer to Figure 2-8:

1. Set deck at transport height. See “Transport

Height” instructions above.

2. Push center button on head of deck stop pin (#3) and

insert pin into desired cutting height pin hole on

cutting height indicator (#4).

3. Push forward on deck lift pedal (#1) with your right

foot, pull back on transport lock handle (#2), and

slowly release deck lift pedal to gently lower deck

against deck stop pin (#3).

Clearing Obstacles

1. If it is necessary to drive over an obstruction, stop

mower, turn off blades, and raise deck fully up to

transport position.

2. Move forward slowly to make certain deck clears the

obstruction.

3. Lower deck to cutting height after mower has passed

over obstruction, engage blades, and continue

mowing.

IMPORTANT: The deck must be level and blades

disengaged before setting deck cutting height. See

instructions for “Deck Leveling” on page 28.

IMPORTANT: See deck stop (#3) in Figure 2-8.

To operate deck stop pin, push in center button on

head of pin to remove & insert pin.

NOTE: Cutting height provided on deck height

indicator (#4) is from 1" to 5" in 1/4" increments.

IMPORTANT: It is best to mow around obstructions;

not over them. Beware, the front of the deck can

clear an obstacle and still make contact by high

centering on the obstacle. Mowing over obstacles

that make contact with the deck can bend/break

mower deck, mower blades, and blade spindles.

.

Deck Lift Pedal

Figure 2-8

Engine Starting

The safety start interlock system is designed to prevent

runaway or accidental entanglement.

The following steps are correct procedures for starting

the engine. If difficulty is encountered, contact your local

Land Pride dealer.

1. Before starting engine, make sure:

a. Blade engagement switch is (OFF).

b. Both control levers are positioned (OUT).

c. Park brake is (ON).

2. Set speed control to approximately 1/2 open throttle.

3. Insert key into ignition switch and rotate clockwise to

engage starter motor. Release key when engine

starts.

4. Perform test to make sure safety start interlock

system is operating properly. Refer to “Safety Start

Interlock System” on page 19.

5. As soon as engine begins to run, check to make

certain oil warning light is off. If not, stop engine

immediately, and check for the cause. Refer to

“Troubleshooting” on page 58.

6. Allow engine to idle a few minutes to warm up before

operating the mower.

35380

IMPORTANT: The starter motor will engage only if

blade engagement switch is (OFF), control levers

are (OUT) , and park brake is (ON).

IMPORTANT: Use choke when engine is cold or if

warm and engine fails to start after 5 seconds of

cranking. Avoid engine flooding by pushing choke

control knob to (OFF) as soon as possible.

IMPORTANT: The engine starter should not be

operated for periods longer then 30 seconds at a

time. An interval of at least two minutes should be

allowed between such cranking periods to protect

the starter from overheating and burn-out.

Page is loading ...

Land Pride ZT360 User manual

This manual is also suitable for

Land Pride ZT360 User manual

Related papers

Other documents