FormNo.3365-187RevA
WeightKit
CommercialWalk-Behind/Stand-OnMowers
ModelNo.117-3620
InstallationInstructions
Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.
Weightsareinstalledtoimprovehandling,balanceand
improveperformance.Weightscanbeaddedorremoved
tocreateoptimizedperformanceunderdifferentmowing
conditionsandforoperatorpreference(Figure1).
Itisrecommendedthatweightsbeadded,relocatedor
removedoneatatimeuntilthedesiredhandlingandbalance
isachieved.
WARNING
Excessiveweightchangescaneffecthandlingand
operationofthemachine.Thiscouldcauseserious
injurytoyouorbystanders.
Makesureweightchangesissmallincrementsonly.
Evaluatethemuferaftereachweightchangeto
ensurethemachinecanbeoperatedsafely.
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
Description
Qty.
Use
Weight1
Carriagebolt(3/8x4inches)
2
Carriagebolt(3/8x5inches)
2
Carriagebolt(3/8x6inches)
2
Flangenut(3/8inch)
2
Installtheweight.
©2012—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.
OriginalInstructions(EN)
PrintedintheUSA.
AllRightsReserved
InstallingtheWeight
1.DisengagethePTO,stoptheengine,removethekey,
andwaitforallmovingpartstostopbeforeleavingthe
operatingposition.
2.Allowtheengineandmufertocoolbeforeinstalling
thiskit.
3.Determinethesizeofboltneededtoinstalltheweights.
Usethefollowingtabletodeterminethelengthofthe
boltneededforthenumberofweightsyouwillbe
installing.
Sizeofbolttouse:
Numberweightstoinstall
3/8x4inches
1
3/8x5inches
2
3/8x6inches
3
WARNING
Contactwithhotsurfacesmaycausepersonal
injury.
•Allowthemuferandenginetocoolbefore
installingthiskit.
•Keephands,feet,face,clothingandother
bodypartsawayfromahotmuferand
engine.
4.Raisetheheight-of-cutlevertotheappropriateposition
toallowthebestclearancesfortheremovaland
installationoffasteners.
5.Removethe4muferguardbolts.Adjusttheguard
positionasneededtoremovethebolts(Figure1).
6.Installthenewboltsthroughthemuferguardand
throughtheclampbar.
7.Installtheweightontotheboltswiththeclampbarin
placebehindtheweight(Figure1).
8.Looselyinstallthenutsandslidethemuferguardleft
orrighttocentertheexhaustoutlettubeinthecenter
ofthemuferguardopening.
9.Tightenthefournutsandensurethemuferexhaust
tubeiscenteredinthemuferguardopening(Figure1).
10.Operatetheheight-of-cutleverthroughfullrangeto
verifyclearanceofthepartsaroundthemuferand
guard.
Figure1
1.Flangenut
4.Muferguard
2.Weight5.Bolt
3.Clampbar6.Centertheexhaustoutlet
tubeinthecenterofthe
muferguardopening
2
/
