MULTIPLEX Model 146 Riser Kit Installation guide

MULTIPLEX
Brand
MULTIPLEX
Model
Model 146 Riser Kit
Type
Installation guide

MULTIPLEX Model 146 Riser Kit

The MULTIPLEX Model 146 Riser Kit is a device designed to elevate a dispensing tower by 4 inches. This can be useful in situations where the counter is too low or the tower needs to be raised for other reasons. The kit includes a riser, mounting template, and all the necessary hardware for installation.

The riser is made of stainless steel and is designed to be durable and easy to clean. The mounting template makes it easy to install the riser in the correct location. The kit also includes a rubber hose for draining the drip pan and barb-stem splicers and tab-clamps for routing the beverage conduit.

MULTIPLEX Model 146 Riser Kit

The MULTIPLEX Model 146 Riser Kit is a device designed to elevate a dispensing tower by 4 inches. This can be useful in situations where the counter is too low or the tower needs to be raised for other reasons. The kit includes a riser, mounting template, and all the necessary hardware for installation.

The riser is made of stainless steel and is designed to be durable and easy to clean. The mounting template makes it easy to install the riser in the correct location. The kit also includes a rubber hose for draining the drip pan and barb-stem splicers and tab-clamps for routing the beverage conduit.

Instructions
Manitowoc Foodservice Sellersburg, 2100 Future Drive, Sellersburg, IN 47172, Tel: 812-246-7000, www.manitowocbeverage.com
EI216368
8/09
Subject: Model 146 Tower 4” Riser Kit
TOWER LOCATION
Tower Location for Self Serve
American Disabilities Act (ADA) rules apply. Maximum distance set back from outside edge of tray rail for a 34"
counter is 12" (30.5 cm) and a 36" (91.4 cm) counter is 10" (25.4 cm)
1. Determine the location where the dispensing tower will be installed.
2. Locate the mounting template provided with the tower installation kit.
3. Using the mounting template as a guide, punch out the required holes in the counter top.
RISER MOUNTING INSTRUCTIONS
1. Using template supplied, drill mounting holes in countertop.
2. Mount riser to countertop through 3/8 diameter holes in riser with appropriate fasteners. Apply 1/4" bead of RTV
under base flange.
3. Route the rubber hose from the drai n pan to the drai n.
4. Locate the barb-stem splicers and tab-clamps in the tee kit. Attach spl icers to condu it per instructions.
5. Route the beverage conduit up through riser to the tower. If the lines of the conduit are different lengths, always
connect the shortest line first. Use two (2) tabclamps per connection.
Model 146 Tower 4” Riser Kit EI216368
Manitowoc Foodservice Sellersburg, 2100 Future Drive, Sellersburg, IN 47172, Tel: 812-246-7000, www.manitowocbeverage.com
.
DO Adhere to all National and Local Plumbing and Electrical Safety Codes.
DO Turn “Off” incoming electrical service switches when servicing, installing, or repairing equipment.
DO Check that all flare fittings on the carbonation tank(s) are tight. This check should be performed with a
wrench to ensure a quality seal.
DO Inspect pressure on Regulators before starting up equipment.
DO Protect eyes when working around refrigerants.
DO Use caution when handling metal surface edges of all equipment.
DO Handle C0
2 cylinders and gauges with care. Secure cylinders properly against abrasion.
DO Store C0
2 cylinder(s) in well ventilated areas.
DO NOT Throw or drop a C0
2 cylinder. Secure the cylinder(s) in an upright position with a chain.
DO NOT Connect the C0
2 cylinder(s) directly to the product container. Doing so will result in an explosion causing
possible death or injury. Best to connect the C0
2 cylinder(s) to a regulator(s).
DO NOT Store C0
2 cylinders in temperature above 125˚ F (51. 7˚ C) near furnaces, radiator or sources of heat.
DO NOT Release C0
2 gas from old cylinder.
DO NOT Touch Refrigeration lines inside units, some may exceed temperatures of 200
˚ F (93.3˚ C).
NOTE: Water pipe connections and fixtures directly connected to a potable water supply shall be sized, installed and
maintained in accordance with Federal, State, and Local codes.
!
Caution
To Avoid Serious Injury Read the following warnings before
beginning an installation. Falure to do so may result in possible
death or serious injury.
!
Warning
DANGER OF ELECTRICAL SHOCK - Disconnect and lock out all
electrical power sources before performing service or maintenance on
this machine -- except when electrical tests are being performed by
qualified service personnel.
  • Page 1 1
  • Page 2 2

MULTIPLEX Model 146 Riser Kit Installation guide

MULTIPLEX
Brand
MULTIPLEX
Model
Model 146 Riser Kit
Type
Installation guide

MULTIPLEX Model 146 Riser Kit

The MULTIPLEX Model 146 Riser Kit is a device designed to elevate a dispensing tower by 4 inches. This can be useful in situations where the counter is too low or the tower needs to be raised for other reasons. The kit includes a riser, mounting template, and all the necessary hardware for installation.

The riser is made of stainless steel and is designed to be durable and easy to clean. The mounting template makes it easy to install the riser in the correct location. The kit also includes a rubber hose for draining the drip pan and barb-stem splicers and tab-clamps for routing the beverage conduit.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents