Table of contents
Comprima CV 150 XC
Original operating instructions 150001057_05_en-GB 7
14.4 Fold in bale turner for driving on public roads..........................................................................199
14.5 Checking road travel lighting....................................................................................................200
14.6 Preparing the machine for shipment ........................................................................................200
14.6.1 Checklist for the transport of the machine ...............................................................................200
14.6.2 Securing the side hoods ..........................................................................................................201
14.6.3 Securing the storage compartment flap ...................................................................................201
14.6.4 Lifting the machine...................................................................................................................202
14.6.5 Lashing the machine................................................................................................................203
15 Settings...................................................................................................................................204
15.1 Setting the baling pressure ......................................................................................................204
15.2 Building up minimum pressure.................................................................................................204
15.3 Setting the bale diameter .........................................................................................................205
15.4 Setting the density of the bale core..........................................................................................205
15.5 Setting the cutting length .........................................................................................................207
15.6 Checking and setting the position of the feed rocker arm........................................................207
15.6.1 Checking and adjusting the feed position ................................................................................208
15.6.2 Checking and setting end position for net wrapping ................................................................209
15.7 Setting wrapping material overhang ........................................................................................209
15.8 Setting wrapping material brake ..............................................................................................210
15.9 Setting the brake force release when feeding wrapping material ............................................211
15.10 Checking and setting the axial play of the brake disc at the wrapping material brake.............212
15.11 Checking the retaining comb for net wrapping.........................................................................213
15.12 Setting the film brake on the wrapping device .........................................................................213
15.13 Setting the pre-stretch of the film in the wrapping device ........................................................214
15.14 Adjusting the gearbox on the wrapping table to the film width.................................................215
16 Maintenance ...........................................................................................................................216
16.1 Observe the service record booklet .........................................................................................216
16.2 Maintenance table....................................................................................................................216
16.2.1 Maintenance – Before the season ...........................................................................................216
16.2.2 Maintenance – After the season ..............................................................................................217
16.2.3 Maintenance – once after 10 hours .........................................................................................218
16.2.4 Maintenance – once after 50 hours .........................................................................................218
16.2.5 Maintenance – every 10 hours, at least daily...........................................................................218
16.2.6 Maintenance – every 50 hours.................................................................................................219
16.2.7 Maintenance – Every 250 hours ..............................................................................................219
16.2.8 Maintenance – Every 500 hours ..............................................................................................219
16.2.9 Maintenance – Every 1,000 round bales .................................................................................219
16.2.10 Maintenance – Every 2 years ..................................................................................................219
16.3 Lubrication chart ......................................................................................................................219
16.4 Lubricating the universal shaft .................................................................................................223
16.5 Tightening torques ...................................................................................................................223
16.6 Checking/maintaining tyres......................................................................................................227
16.7 Servicing the main gearbox .....................................................................................................228
16.8 Servicing hydraulic pump gearbox...........................................................................................229
16.9 Cleaning the machine ..............................................................................................................230
16.10 Cleaning deflection pipes or conical tying roller.......................................................................231
16.11 Clean the bushing and the drawbar eye ..................................................................................231
16.12 Cleaning drive chains...............................................................................................................232
16.13 Protecting brake disc of the wrapping material brake from corrosion ......................................232
16.14 Checking the screw connections on the drawbar ....................................................................232
16.15 Setting the scraper and stone deflector ...................................................................................233
16.15.1 Adjusting the scraper in relation to the lower compression roller.............................................233
16.15.2 Adjusting the scraper on the deflection shafts .........................................................................234
16.15.3 Setting the stone deflectors .....................................................................................................234
16.16 Releasing the cam clutch on the universal shaft......................................................................235
16.17 Changing the blades ................................................................................................................235
16.18 Unlocking/locking blade retaining shaft....................................................................................237
16.19 Checking and moving the blade retaining shaft .......................................................................238
16.20 Grinding the blades..................................................................................................................239
16.21 Checking/lubricating the safety rolls of the single blade locking device...................................240