Table of contents
Comprima CV 150 XC
Original operating instructions 150001057_05_us 7
14.4 Fold in bale turner for driving on public roads..........................................................................197
14.5 Checking road travel lighting....................................................................................................198
14.6 Preparing the machine for shipment ........................................................................................198
14.6.1 Checklist for the transport of the machine ...............................................................................198
14.6.2 Securing the side hoods ..........................................................................................................199
14.6.3 Securing the storage compartment flap ...................................................................................199
14.6.4 Lifting the machine...................................................................................................................200
14.6.5 Lashing the machine................................................................................................................201
15 Settings...................................................................................................................................202
15.1 Setting the baling pressure ......................................................................................................202
15.2 Building up minimum pressure.................................................................................................202
15.3 Setting the bale diameter .........................................................................................................203
15.4 Setting the density of the bale core..........................................................................................203
15.5 Setting the cutting length .........................................................................................................205
15.6 Checking and setting the position of the feed rocker arm........................................................205
15.6.1 Checking and adjusting the feed position ................................................................................206
15.6.2 Checking and setting end position for net wrapping ................................................................207
15.7 Setting wrapping material overhang ........................................................................................207
15.8 Setting wrapping material brake ..............................................................................................208
15.9 Setting the brake force release when feeding wrapping material ............................................209
15.10 Checking and setting the axial play of the brake disc at the wrapping material brake.............210
15.11 Checking the retaining comb for net wrapping.........................................................................211
15.12 Setting the film brake on the wrapping device .........................................................................211
15.13 Setting the pre-stretch of the film in the wrapping device ........................................................212
15.14 Adjusting the gearbox on the wrapping table to the film width.................................................213
16 Maintenance ...........................................................................................................................214
16.1 Observe the service record booklet .........................................................................................214
16.2 Maintenance table....................................................................................................................214
16.2.1 Maintenance – Before the season ...........................................................................................214
16.2.2 Maintenance – After the season ..............................................................................................215
16.2.3 Maintenance – once after 10 hours .........................................................................................216
16.2.4 Maintenance – once after 50 hours .........................................................................................216
16.2.5 Maintenance – every 10 hours, at least daily...........................................................................216
16.2.6 Maintenance – every 50 hours.................................................................................................217
16.2.7 Maintenance – Every 250 hours ..............................................................................................217
16.2.8 Maintenance – Every 500 hours ..............................................................................................217
16.2.9 Maintenance – Every 1,000 round bales .................................................................................217
16.2.10 Maintenance – Every 2 years ..................................................................................................217
16.3 Lubrication chart ......................................................................................................................217
16.4 Lubricating the universal shaft .................................................................................................221
16.5 Tightening torques ...................................................................................................................221
16.6 Checking/maintaining tyres......................................................................................................225
16.7 Servicing the main gearbox .....................................................................................................226
16.8 Servicing hydraulic pump gearbox...........................................................................................227
16.9 Cleaning the machine ..............................................................................................................228
16.10 Cleaning deflection pipes or conical tying roller.......................................................................229
16.11 Clean the bushing and the drawbar eye ..................................................................................229
16.12 Cleaning drive chains...............................................................................................................230
16.13 Protecting brake disc of the wrapping material brake from corrosion ......................................230
16.14 Checking the screw connections on the drawbar ....................................................................230
16.15 Setting the scraper and stone deflector ...................................................................................231
16.15.1 Adjusting the scraper in relation to the lower compression roller.............................................231
16.15.2 Adjusting the scraper on the deflection shafts .........................................................................232
16.15.3 Setting the stone deflectors .....................................................................................................232
16.16 Releasing the cam clutch on the universal shaft......................................................................233
16.17 Changing the blades ................................................................................................................233
16.18 Unlocking/locking blade retaining shaft....................................................................................235
16.19 Checking and moving the blade retaining shaft .......................................................................236
16.20 Grinding the blades..................................................................................................................237
16.21 Checking/lubricating the safety rolls of the single blade locking device...................................238