Equip eSATA/-USB 2.0 Express Card/34, 2-Port Specification
- Category
- Interface cards/adapters
- Type
- Specification
eSATA/-USB 2.0
EXPRESS CARD
2-PORT
Expansion | 111828
1
1. Introduction
equip eSATA/-USB 2.0 Express Card enhances your Notebook/Netbook
computer with 1x eSATA and 1x USB 2.0 port from a single Express Card slot.
This Express Card is fully compliant with SATA II 3.0 Gbps on the device side to
access Serial ATA mobile external and internal storage devices. It comes with
drivers for Windows 2000, XP and Vista 32/64-bit
2
1.1 Features
eSATA (external SATA II) Interface
External SATA II (eSATA) Connector
48 bits LBA can Break Capacity-Limit to Support HDD larger than 137GB
Hot-plug capability
Supports SATA II transfer rate of 3.0 Gbps
Fully compliant with Serial ATA 1.0 specifications
Supports Legacy Command Queuing (LCQ)
Supports Native Command Queuing (NCQ)
Supports Non-zero offsets NCQ
Supports Out of order data delivery NCQ
Supports FIS-based switching with Port Multipliers
31 Commands and Scatter/Gather Tables per Port
LED indicate for HDD access
3
USB 2.0 Interface
Compliant with Universal Serial Bus Specification Revision 2.0
Compliant with Open Host Controller Interface Specification for USB Rev
1.0a
Compliant with Enhanced Host Controller Interface Specification for USB
USB port supports high-speed (480 Mbps), full-speed (12 Mbps), and low-
speed (1.5 Mbps) transaction
1.2 Package Contents
1x Express Card
1x eSATA Cable
1x Driver Disc
1x User Manual
4
1. Software Installation
Windows 2000 / XP / Vista Installation
1. Insert eSATA/-USB 2.0 Express Card into an available slot. Connect serial ATA
cable(s) between the SATA port and serial ATA device(s).
2. Windows will display the “Found New Hardware Wizard”, “Mass
Storage controller”.
3. Select “Install from a list or specific location (Advanced)”, and click
“Next”, and make sure the Driver Disc is in your CD-ROM/DVD
4. Select “Search for the best driver in these locations”, and check
“Include this location in the search” uncheck the other boxes.
5. Type in E:\ (If your CD-ROM/DVD is E:\) then click “Browse”.
6. Points specify a location, example E:\ SATAII 3Gbps_Non-Raid_1Port \Sil3x31
\ 32bit_Windows, and click “OPEN” then “OK”
7. When the wizard indicates that it found a driver for the device click “Next”
8. If the “Hardware Installation” dialog appears, click “Continue Anyway”
9. The wizard will now copy the required files to the system and start the
Driver. After starting the driver the wizard will display a completion dialog,
click “Finish” to exit the wizard.
5
Verifying the Installation Windows 2000 / XP / Vista
1. Right click on “My Computer” icon, select “Properties”, left click on
“Hardware” tab, and then on “Device Manager” button.
2. Double click on “SCSI and RAID Controllers” If there is no exclamation
mark (!) or question mark (?) showing at the front of Silicon Image SiI 3531
SATALink Controller, the driver is started correctly.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
11
Related Products
#111827 USB 2.0 Express Card 2-Port
#111829 RS-232 Serial Express Card 1-Port
Please visit us at www.equip-info.net
for more detail.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Equip eSATA/-USB 2.0 Express Card/34, 2-Port Specification
- Category
- Interface cards/adapters
- Type
- Specification
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Equip 111827-V1 Datasheet
-
Equip USB 2.0 Express Card/34, 2 Ports User manual
-
Equip 351001 Installation guide
-
Equip 351004 Installation guide
-
-
-
-
-
-