Topfield TF 5000 PVRt Masterpiece User manual

Topfield
Brand
Topfield
Model
TF 5000 PVRt Masterpiece
Type
User manual
TOPFIELD
TF 5000 PVRt Masterpiece
User Guide
Digital Terrestrial Receiver
Personal Video Recorder
Contents iii
Contents
1 Introduction 1
1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 Controlling the digital receiver . . . . . . . . . . . . . . . . . . 2
1.2.1 The front panel . . . . . . . . . . . . . . . . . . . . . . . 3
1.2.2 The remote control . . . . . . . . . . . . . . . . . . . . . 4
2 Setup 7
2.1 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2 Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.3 Rear panel connections . . . . . . . . . . . . . . . . . . . . . . . 9
2.4 Connecting up your digital receiver . . . . . . . . . . . . . . . 11
2.4.1 Connecting the antenna . . . . . . . . . . . . . . . . . . 11
2.4.2 Connecting to your television . . . . . . . . . . . . . . 12
2.4.3 Connecting to your video cassette recorder . . . . . . . 14
2.5 Switching on for the first time . . . . . . . . . . . . . . . . . . . 14
2.5.1 Inserting batteries in the remote control . . . . . . . . . 15
2.5.2 Powering on and checking picture . . . . . . . . . . . . 15
iv Contents
3 Preference Settings 16
3.1 Language settings . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.2 Video and audio settings . . . . . . . . . . . . . . . . . . . . . . 18
3.2.1 Television standard . . . . . . . . . . . . . . . . . . . . 18
3.2.2 Colour model . . . . . . . . . . . . . . . . . . . . . . . . 19
3.2.3 Video cassette recorder . . . . . . . . . . . . . . . . . . 19
3.2.4 Television aspect ratio . . . . . . . . . . . . . . . . . . . 20
3.2.5 Sound mode . . . . . . . . . . . . . . . . . . . . . . . . 20
3.2.6 Radio frequency output . . . . . . . . . . . . . . . . . . 21
3.3 Local time setting . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.4 Parental control . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.5 Adjusting the on-screen display . . . . . . . . . . . . . . . . . . 24
3.6 To turn on the time shift feature . . . . . . . . . . . . . . . . . . 25
4 Service Search 26
4.1 Searching broadcasting services . . . . . . . . . . . . . . . . . . 26
4.2 Resetting to factory settings . . . . . . . . . . . . . . . . . . . . 27
5 Daily Usage 28
5.1 Volume control . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
5.2 Watching television . . . . . . . . . . . . . . . . . . . . . . . . . 28
5.2.1 The services list . . . . . . . . . . . . . . . . . . . . . . . 28
5.2.2 The favourite services list . . . . . . . . . . . . . . . . . 30
5.2.3 Viewing programme information . . . . . . . . . . . . 31
5.2.4 Selecting audio tracks . . . . . . . . . . . . . . . . . . . 32
5.2.5 Selecting subtitle tracks . . . . . . . . . . . . . . . . . . 32
5.2.6 Viewing teletext . . . . . . . . . . . . . . . . . . . . . . 32
5.3 Viewing electronic programme guide . . . . . . . . . . . . . . 33
5.4 Watching multifeed programme . . . . . . . . . . . . . . . . . 34
5.5 Using time shift . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
5.6 Using picture in picture . . . . . . . . . . . . . . . . . . . . . . 36
Contents v
6 Listing Services 38
6.1 Editing the favourite list . . . . . . . . . . . . . . . . . . . . . . 38
6.2 How to use on-screen keyboard . . . . . . . . . . . . . . . . . . 40
6.3 Transferring receiver data . . . . . . . . . . . . . . . . . . . . . 40
7 Recording and Playing 42
7.1 Recording a programme . . . . . . . . . . . . . . . . . . . . . . 43
7.1.1 Instant recording . . . . . . . . . . . . . . . . . . . . . . 43
7.1.2 Timer recording . . . . . . . . . . . . . . . . . . . . . . 45
7.1.3 Scheduling a recording using the programme guide . 48
7.1.4 Recording a time-shifted programme . . . . . . . . . . 48
7.2 File archive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
7.2.1 To delete a recording . . . . . . . . . . . . . . . . . . . . 50
7.2.2 To sort recordings . . . . . . . . . . . . . . . . . . . . . 50
7.2.3 To lock a recording . . . . . . . . . . . . . . . . . . . . . 50
7.2.4 To rename a recording . . . . . . . . . . . . . . . . . . . 51
7.2.5 To make a new folder . . . . . . . . . . . . . . . . . . . 51
7.2.6 To move a recording to another folder . . . . . . . . . . 51
7.3 Playing back a recording . . . . . . . . . . . . . . . . . . . . . . 51
7.3.1 To navigate using the progress bar . . . . . . . . . . . . 52
7.3.2 To play in slow motion . . . . . . . . . . . . . . . . . . 53
7.3.3 To play in fast motion . . . . . . . . . . . . . . . . . . . 53
7.3.4 To make a bookmark . . . . . . . . . . . . . . . . . . . . 53
7.3.5 To play back a recording repeatedly . . . . . . . . . . . 54
7.3.6 To play back recordings in sequence . . . . . . . . . . . 54
7.4 Editing a recording . . . . . . . . . . . . . . . . . . . . . . . . . 55
7.5 Copying a recording . . . . . . . . . . . . . . . . . . . . . . . . 55
7.6 MP3 playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
7.7 Transferring recording files . . . . . . . . . . . . . . . . . . . . 57
7.8 Formatting the hard disk . . . . . . . . . . . . . . . . . . . . . . 58
vi Contents
8 Topfield Application Program 60
9 Firmware Update 62
9.1 Checking the firmware information . . . . . . . . . . . . . . . 62
9.2 From your computer via USB port . . . . . . . . . . . . . . . . 64
9.3 From your computer via RS-232 port . . . . . . . . . . . . . . . 65
9.4 From another digital receiver via RS-232 port . . . . . . . . . . 66
Index 67
1
Chapter 1
Introduction
The TF 5000 PVRt Masterpiece digital receiver is fully compli-
ant with the international Digital Video Broadcasting (DVB)
standard, and can receive digital broadcasts. For its operation
you need an antenna, which must be installed appropriately.
NOTE
In general we equate a channel with a frequency. Unlike ana-
logue broadcasts, however, digital broadcasts are not all as-
signed to their own frequencies; instead, multiple television
broadcasts are transmitted through a single frequency. The fre-
quency in digital broadcasting is usually called transponder. To
reduce confusion in this manual, the word
service
is preferably
used than
channel
as a term to indicate one television or radio
broadcast.
1.1 Features
The TF 5000 PVRt Masterpiece digital receiver has the following
features:
• Can store up to 2000 television and radio services.
2 Introduction
• You can create favourite lists of your favourite services.
•
You can view information about the current television or
radio programme.
•
Has an electronic programme guide that provides an
overview of scheduled programmes.
•
You can update the firmware of the digital receiver to the
latest version, provided by the manufacturer.
•
You can record one broadcasting service while you are
currently watching another.
•
The large storage capacity of the built-in hard disk drive
allows you to record up to about 60 hours of television
—in case of 250 gigabytes— in excellent picture and sound
quality.
•
Time shift is a special technical feature available on the TF
5000 PVRt Masterpiece. You can pause the programme
you are watching and resume it again at a later time.
Then you can quickly go to whatever part of the current
programme by fast foward and rewind search.
1.2 Controlling the digital receiver
The digital receiver can be operated with the remote control
and the buttons on the front panel.
NOTE
When the digital receiver is off but plugged into a wall outlet,
we say that it is in standby mode; on the other hand, when it is
on, it is in operation mode. Even when you are not using the
digital receiver, you should keep it plugged into a wall outlet
to be in standby mode so that it can run timer events at any
time.
1.2 Controlling the digital receiver 3
1.2.1 The front panel
The front panel of the digital receiver has buttons to control the
digital receiver, and specific lamps and a display to indicate its
status. The following indicates what they mean.
STANDBY
button switches the digital receiver between
standby mode and operation mode.
CHANNEL ,
buttons switch to previous or next service.
They are also used to navigate in menus and interactive
screens.
VOLUME ,
buttons decrease or increase the volume.
They are also used to change values for menu options.
Front display
displays the current time in standby mode,
and displays the current service in operation mode.
4 Introduction
1.2.2 The remote control
1
4
6
3
7
10
16
9
12
18
20
13
27
35
32
31
23
28
36
5
8
2
14
11
17
15
12
11
24
19
25
34
33
29
30
21
22
37
26
1
button switches the digital re-
ceiver between standby mode and
operation mode.
2
mutes the sound. Press again to
switch it back on.
3
UHF
displays the radio frequency
setting menu. See
§
3.2.6 for more
details.
4
switches the output of the TV
SCART socket between the digital
receiver and the device connected to
the VCR SCART socket. See
§
3.2.3
for more details.
5
is used to set a sleep timer.
6
Numeric buttons are used to enter a
service number for service change or
to specify values for menu options.
7
switches between the current ser-
vice and the previously viewed one.
8
displays the service information
box. It is also used to display more
information about a programme.
9
GUIDE
displays the electronic pro-
gramme guide.
10
MENU
displays the main menu. It is also used to return
to the previous menu from a submenu.
11
P−
,
P+
buttons switch to previous or next service.
They are also used to navigate in menus and interactive
screens.
1.2 Controlling the digital receiver 5
12
V−
,
V+
buttons decrease or increase the volume. They
are also used to change values for menu options.
13
OK
displays the services list. See
§
5.2.1 for more details.
It is also used to select a menu item.
14
FAV displays the favourite lists.
15
EXIT is used to exit the current screen.
16
switches between television services and radio ser-
vices.
17
is used to select an audio track and a sound mode, or
a video track of multifeed programme.
18
is used to select a subtitle track.
19
displays teletext.
20
is used to display, minify or hide the sub-screen. See
§ 5.6 for information about picture-in-picture.
21
changes the position of sub-screen counterclockwise.
It is also used to jump back to beginnng of recording
during a playback.
22
changes the position of sub-screen clockwise. It is
also used to jump to end of recording during a playback.
23
SAT
swaps the sub-picture with the main picture. See
§ 5.6 for more details.
24
displays the services list for sub-screen. It is also used
to specify a block for editing or for repeated playback.
25
is used to jump back 10 seconds for an instant replay.
It is also used to edit a recording.
26
is used to jump to next bookmark position or to jump
forward by 30 seconds.
27
is used to make a bookmark during playback or time
shift.
6 Introduction
28
resumes normal playback speed, or displayes the
progress bar for navigation on playback or time shift. To
play a recorded programme, see button 35.
29
is used to start reverse playback. Subsequent presses
increase the rewind speed.
30
is used to start fast motion playback. Subsequent
presses increase the playback speed.
31
is used to start slow motion playback. Subsequent
presses change the playback speed.
32
pauses live television or playback of a recorded
programme.
33
is used to start recording.
34
is used to stop playback, to stop recording, or to
jump back to live television from time-shifted television.
35
is used to display the list of recorded programmes
that are stored on the internal hard disk drive. See
§
7.2
for more details.
36
N/P is not used in this model.
37
M is not used in this model.
The , , , and buttons have additional different
functions per menu besides their own function. They will be
guided by on-screen help.
If the remote control does not work, please check the remote
control mode. There are four modes with this remote control.
You can alter the mode by pressing two buttons simultaneously
as follows:
• Mode 1: +
1
• Mode 2: +
2
• Mode 3: +
3
• Mode 4: +
4
The mode 1 will work at default.
7
Chapter 2
Setup
2.1 Unpacking
Before going any further, check that you have received the
following items with your digital receiver.
• Remote control unit
• Two batteries for the remote control (AAA 1.5 V)
•
One loop cable to link the first tuner with the second
tuner
• One SCART-to-component cable
• One composite cable (RCA cable)
• A copy of this user guide
NOTE
Accessories may vary according to your local area.
2.2 Safety precautions
Please read carefully the following safety precautions.
8 Setup
•
The mains power must be 90 to 250 volts. Check it before
connecting the digital receiver to the wall outlet. For
the power consumption of the digital receiver, refer to
Table 2.1.
•
The wall outlet should be near the equipment. Do not
run an extension lead to the unit.
•
Do not expose the digital receiver to any moisture. The
digital receiver is designed for use indoors only. Use dry
cloth when cleaning the digital receiver.
• Place the digital receiver on a firm and level surface.
•
Do not place the digital receiver close to heat emitting
units or in direct sunlight, as this will impair cooling.
Do not lay any objects such as magazines on the digi-
tal receiver. When placed in a cabinet, make sure there
is a minimum space of 10 centimetres around it. For
the physical specification of the digital receiver, refer to
Table 2.2.
•
Protect the power cord from being walked on or pinched.
If the wires are exposed or the cord is damaged, do not
use the digital receiver and get the cord replaced.
•
Never open the digital receiver casing under any circum-
stances. The warranty will be void.
• Refer all servicing to a qualified service technician.
Table 2.1: Power specifications
Input voltage 90 to 250 V AC, 50/60 Hz
Power consumption 28 W at maximum in operation
10 W in standby
2.3 Rear panel connections 9
Table 2.2: Physical specifications
Size 430× 60× 265 mm
Weight 4.3 kg
Operating temperature 0 to 45 °C
Storage relative humidity 5 to 95 %
2.3 Rear panel connections
The TF 5000 PVRt Masterpiece has a wide range of connections
on the back panel.
ANT 1
RF LOOP 1 OUT RF LOOP 2 OUT AUDIO
L
R
S-VIDEO VCR USB
RF IN
S/PDIF RS-232
VIDEO
TV
RF OUT
ANT 2
1
3
2 4 6 7 9 10 12 13 14
5
8 11
Check what connections your television set has in comparison
with the digital receiver.
1
ANT 1
Terrestrial broadcasting signal input socket
for the first tuner.
2
RF LOOP 1 OUT
Terrestrial broadcasting signal output
socket through the first tuner.
3
ANT 2
Terrestrial broadcasting signal input socket
for the second tuner.
4
RF LOOP 2 OUT
Terrestrial broadcasting signal output
socket through the second tuner.
5
VIDEO
Composite video output socket for the televi-
sion set. (yellow)
10 Setup
6
AUDIO L/R
Stereo audio output socket for the television
set or the audio system. (white/red)
7
S-VIDEO
Super video output socket for the television
set.
8
TV
Audio and video output socket for the televi-
sion set.
9
VCR
Audio and video input/output socket for the
video cassette recorder or suchlike.
10
USB
USB port for firmware update and data trans-
fer.
11
RF OUT Analogue television output socket.
12
RF IN Analogue television input socket.
13
S/PDIF
Dolby digital output socket for the audio sys-
tem.
14
RS-232
Serial port for firmware update and data
transfer.
Table 2.3: Connectors specifications
VIDEO Composite video (CVBS) output
AUDIO Left & right audio output
S-VIDEO Super video (S-Video) output
TV CVBS/S-Video/RGB/YUV video output
Left & right audio output
VCR CVBS video output
Left & right audio output
CVBS/S-Video/RGB/YUV video input for bypass
Left & right audio input for bypass
S/PDIF Dolby digital audio output
RS-232 115.2 kbps at maximum
USB 2.0
2.4 Connecting up your digital receiver 11
2.4 Connecting up your digital receiver
There are several ways to set up the digital receiver. Set up the
digital receiver suitably to your television and other appliances.
If you have any problem with your setup or need help, contact
your dealer.
2.4.1 Connecting the antenna
Whatever sort of connection you have be-
tween the digital receiver and the television,
you need to connect the digital receiver to
your television antenna so that it can receive
digital television services.
Connect the antenna cable to the ANT 1 con-
nector on the back panel of the digital re-
ceiver.
Also, you must ensure that there is a connec-
tion to both the ANT 1 and ANT 2 connectors
on your digital receiver, so that both tuners
work properly.
Normally you do that by using a loop cable to link from the RF
LOOP 1 OUT connector to the ANT 2 connector.
NOTE
However, if you are in a weak signal area, or are using a signal
amplifier with more than one output, you may achieve better
results by connecting a cable from the antenna or amplifier
directly to the ANT 2 connector rather than using the loop
cable.
If you have another digital receiver, or you want to still receive
analogue channels on your television, link it from the RF LOOP
2 OUT connector.
12 Setup
2.4.2 Connecting to your television
Between all the following connectors of the digital receiver, we
recommend you to use the first connector to get best picture
quality. If your television does not have the matching connector,
then use the next connector in the following order for better
picture quality.
1. SCART connector (TV)
2. S-Video connector (S-VIDEO)
3. Composite connector (VIDEO)
4. RF connector (RF OUT)
You should configure audio and video settings after connecting
up the digital receiver. See § 3.2 for detailed description.
To use the SCART connector
For best results with a standard television set,
you should use a SCART cable, plugging one
end into the TV socket on the digital receiver
and the other end into a free SCART socket
on your television.
Some televisions have inputs via Component
connector or S-Video connector rather than
SCART.
If you have such a television, use an appropriate conversion ca-
ble to link the TV socket on the digital receiver to the matching
socket on your television.
If you connect with a standard SCART cable, you do not have
to make audio connections because the SCART connector can
output stereo audio. But if you use a conversion cable, such as
SCART-to-Component, you have to make audio connections.
2.4 Connecting up your digital receiver 13
To use the S-Video connector
You will need to obtain a S-Video cable to use
the S-Video connector. Plug one end of the
cable into the S-VIDEO socket on the digital
receiver, and the other end into the matching
socket on your television.
To use the composite video connector
You will need to obtain a composite video
cable (RCA cable) to use the composite video
connector. Plug one end of the cable into the
VIDEO (yellow) socket on the digital receiver,
and the other end into the matching socket
on your television.
To connect the audio connectors
You will need to obtain an audio cable (RCA
cable) to connect the audio connectors. Plug
one end of the cable into the AUDIO L (white)
and AUDIO R (red) sockets on the digital re-
ceiver, and the other end into the matching
sockets on your television or audio system.
To enjoy Dolby digital audio, your televi-
sion or audio system must be able to decode
Dolby digital audio, and you will need to ob-
tain a S/PDIF cable. Plug one end of the
cable into the S/PIDF socket on the digital
receiver, and the other end into the matching
socket on your audio system.
14 Setup
To use the RF connector
If your television does not have any video and audio input, you
will need to use the radio frequency output from the digital
receiver.
In this case, you will need to connect a ca-
ble from the RF OUT socket to the antenna
connector on your television. To ensure your
television can also pick up existing analogue
channels as well, you will need to connect
a cable from RF LOOP 2 OUT connector on
the back of the digital receiver to the RF IN
connector.
Tune your television set to channel 36 so that
you can see the output from the digital re-
ceiver.
2.4.3 Connecting to your video cassette recorder
The digital receiver can also output video to another appliance
such as a video cassette recorder or video receiver through an
auxiliary SCART connector.
You will need to obtain a SCART cable to use
the auxiliary SCART connector. Plug one end
of the cable into the VCR socket on the digital
receiver, and the other end into the match-
ing socket on your video cassette recorder or
suchlike.
2.5 Switching on for the first time
Now that you have your digital receiver connected, you should
plug it in to a mains socket. Ensure that your television set is
turned on, so that you will be able to see the display from the
digital receiver.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78

Topfield TF 5000 PVRt Masterpiece User manual

Topfield
Brand
Topfield
Model
TF 5000 PVRt Masterpiece
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents