AirLive SmartCube 300W IP-Camera User guide

SmartCube 300W

Intelligent 3MP Wireless Cube

IPCAM with Temperature and

Humidity Sensor

User’s Manual

Copyright and Disclaimer

AirLive SmartCube 300W User’s Manual

Copyright & Disclaimer

No part of this publication may be reproduced in any form or by any means, whether

electronic, mechanical, photocopying, or recording without the written consent of OvisLink

Corp.

OvisLink Corp. has made the best effort to ensure the accuracy of the information in this

user’s guide. However, we are not liable for the inaccuracies or errors in this guide.

Please use with caution. All information is subject to change without notice

This product contains some codes from GPL. In compliance with GPL agreement, AirLive

will publish the GPL codes on our website. Please go to www.airlive.com and go to the

"Support->GPL" menu to download source code.

All Trademarks are properties of their respective holders.

Copyright and Disclaimer

AirLive SmartCube 300W User’s Manual

FCC Statement

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the A

user is encouraged to try to correct the interference by one of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

FCC Caution

Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment. This device complies

with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation. For

product available in the USA/Canada market, only channel 1~11 can be operated.

Selection of other channels is not possible.

This device and its antenna(s) must not be co-located or operation in conjunction with any

other antenna or transmitter.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance

20cm between the radiator & your body.

WEEE Marking Warning:

The crossed out wheeled bin indicates the product must not be disposed together with

household waste. For the sake of the environment, the product should only be given to

entities involved in the reception of waste electronic and electrical equipment. The lists of

entities entitled to receive used equipment can be found on the websites of municipalities.

Some components of devices such as external wiring, circuit boards and liquid crystal

displays have a negative impact on the environment.

Table of Contents

AirLive SmartCube 300W User’s Manual

iii

Table of Contents

1. Overview ..................................................................................................... 1

1.1 Introduction .......................................................................................... 1

1.2 Features ............................................................................................... 2

1.3 Product Specification ........................................................................... 2

1.4 System Requirement ........................................................................... 5

2. Package Contents and Installation ........................................................... 7

2.1 Package Contents ................................................................................ 7

2.2 WiFi Connections ................................................................................. 7

2.3 Connect to IP Camera ...................................................................... 10

3. Using IP Camera via Web Browser ......................................................... 12

3.1 Windows Web Browser ...................................................................... 12

4. AirLive APPCAM via iOS/Android device .............................................. 15

4.1 Using AirLive APPCAM via iOS/Android device ................................. 15

5. Operating the Network Camera .............................................................. 25

5.1 Live View ............................................................................................ 25

5.2 Setup Wizard ..................................................................................... 27

5.3 Configuration ..................................................................................... 33

6. Configuration ........................................................................................... 34

6.1 Network .............................................................................................. 35

6.2 Video .................................................................................................. 43

6.3 Audio .................................................................................................. 51

6.4 Event .................................................................................................. 52

6.5 Storage .............................................................................................. 60

6.6 System ............................................................................................... 62

6.7 Status ................................................................................................. 68

7. Appendix A ............................................................................................... 71

7.1. Video Analytics ................................................................................. 71

Table of Contents

AirLive SC-300W User’s Manual

iv

7.2. Face Recognition: ............................................................................. 73

7.3. iMotion Detection (Intelligent Motion Detection) ............................... 75

7.4. Trip Zone ........................................................................................... 76

7.5. Object Counting ................................................................................ 77

7.6. e-Fence ............................................................................................. 79

8. Appendix B ............................................................................................... 81

8.1. How to create App for Dropbox ......................................................... 81

1. Overview

AirLive SmartCube 300W User’s Manual

1

1.

Overview

This user’s manual explains how to operate this camera from a computer. A user should

read this manual completely and carefully before you operate the device.

1.1 Introduction

AirLive SmartCube 300W is a high-end 3 Megapixels H.264/MPEG4/MJPEG Cube Type

WiFi Network Camera, a standalone system that can be connected directly to an Ethernet,

Fast Ethernet or Wireless network. The elegant design makes it an ideal solution for offices,

shops and homes. Moreover, the camera are equipped with IR LEDs and IR-cut filter,

providing clear video in completely dark environments.

The camera boasts high-definition video resolution, allowing for the delivery of extremely

detailed images and coverage 6 or more times or larger than a VGA camera. To maximize

the benefit of the high-definition sensor, the camera employs several innovative

technologies for optimized bandwidth efficiency. Users can also receive only the portions of

the images they are interested in via the cropping function. Furthermore, multiple video

streams can be delivered simultaneously in different resolutions, frame rates, and image

qualities for viewing on different platforms so as to meet different needs or bandwidth

constraints. The camera also offers activity adaptive streaming support that dynamically

allocates bandwidth according to the video content and trigger state.

1. Overview

AirLive SC-300W User’s Manual

2

Moreover, the cameras boast 802.11b/g/n compatible wireless connection, making

installation easier and more cost-efficient. The WPS function of camera makes wireless

configuration easy and straightforward.

With other advanced features such as tamper detection, Micro SDHC/SDXC card onboard

storage, and two-way audio, the camera is a full-fledged surveillance solution for indoor

environments. The simple installation procedures and web-based interface allow you to

integrate it into your network easily. With comprehensive applications supported, the

camera is your best solution for remote monitor, high quality, and high performance video

images.

1.2 Features

This manual will illustrate the steps of how to setup and operate this IP camera, so you’ll

also soon be enjoying the benefits of these product features:

 3 Megapixel Resolution

 Temperature and Humidity Sensor

 Door Cam Mode

 Store Entrance Mode

 Built-in Audio and Speaker

 PIR Sensor

 Intelligent Video Analytics

 Corridor Mode

 ICR Night vision

 Micro SDXC Card slot and Cloud Recording Backup

1.3 Product Specification

Model

SmartCube 300W

Camera

Camera Type

Smart Cube Type

Max Resolution

2048x1536

Image Sensor 1/3" CMOS sensor

Sensor

Resolution

2048x1536

Lens Type

3.6 mm

F= 2.0

Night Vision

Yes

1. Overview

AirLive SmartCube 300W User’s Manual

3

Max IR Distance

15m

Minimum

Illumination

0.1 LUX

Mechanical

IR-Cut Filter

Yes

Viewing Angle 80°(D) 72 °(H) 47 °(V)

Analog Video

Out

None

Video

Compression

H.264

MPEG-4

MJPEG

Video Profile Yes

Resolution and

Frame Rate

20 fps @ 2048 X 1536

30 fps @ 1920 X 1080

30 fps @ 1280 x 1024

30 fps @ 1280 X 720

30 fps @ 720 X 480

30 fps @ 640 X 480

30 fps @ 320 X 240

30fps @ 176 X 144

Streaming

Streaming over UDP, TCP, or HTTP

3GPP mobile view

Configurable frame rate and bandwidth

Support both CBR and VBR

Region of

Interest

Yes

Image

Processing

AE, AW, BLC,WDR, 3DNR, Fog Compensation

Brightness, Sharpness, Contrast, Saturation

Mirror/Flip, NTSC/PAL

Privacy Masks

Text, time date and image OSD

Digital Zoom

10X

Audio

Audio Encoder

G.711

Audio Streaming

Two-way

Audio

Input/ Output

Built-in speaker & microphone

Network

Ethernet Ethernet (10/100 Base-T), RJ-45

1. Overview

AirLive SC-300W User’s Manual

4

Wireless

802.11n

Supported

Protocols

TCP/IP, IPV6, UDP, ICMP, DHCP, NTP, DNS,

DDNS, SMTP, FTP, HTTP, HTTPs, Samba,

PPPoE, UPnP, Bonjour, RTP, RTSP, RTCP,

DLNA, ISCSI, Onvif Profile S

Security

Password protection

IP filter, HTTPS encrypted data transmission

Users

Up to 10 users simultaneous

LED and Button

Power LED

Red Color

Link/Act. LED

Green Color/Flash Green

Reset Button

Power the camera and push and hold Reset

button for 10 seconds

General

Network

Processor

DSP Base

System ROM

128M byte NAND Flash

System RAM

128M byte DDR SDRAM

Power Supply

DC 5V/1A

Power

Consumption

4 Watts Max.

Connector

RJ-45 10BaseT/100BaseTX

DC 5V power jack

Environment

Operation: Temp: -5

℃

~ 55

℃

Humidity: 20% ~ 85% non-condensing

Storage: Temp: -15

℃

~ 60

℃

Humidity: 0% ~ 90% non-condensing

SD card slot

Micro SDXC

Dimension

H x W x D: 94 x 64 x 40 mm

System Integration

Software

Search & Installation-IP Wizard II

CamPro Express 64,Campro Professional,

CamPro VMS

APPCAM, AirLive CamPro Mobile

Event Triggers

Motion detection

Tamper Detection

Periodically Time

SD Card Read/Write Fail Detection

Network Disconnect

Audio Detection

Face Detection

iMotion Detection

1. Overview

AirLive SmartCube 300W User’s Manual

5

Trip Zone

Object Counting

Face recognition

e-Fence

Motion Detection

3

Event handler

FTP, Samba Server, SD card file upload,

Dropbox

E-mail notice

Push Notification

HTTP and TCP notification

Audio File Playback

UPNP

Yes

Application

Programming

Interface

Onvif Profile S

Open API for software integration

SDK

Video Buffer

Pre- and post- alarm buffering

Alarm Triggers

Motion detection, Tamper Detection,

Periodically Time, SD Card Read/Write Fail

Detection, Network Disconnect, Audio

Detection, Face Detection, iMotion Detection,

Trip Zone, Object Counting, Face recognition,

e-Fence.

continuous

Recording

Yes

Viewing System

OS

Windows VISTA / Windows XP / Windows 7/

Windows 8, Windows 10

Browser

Internet Explorer (8.0+) / Chrome / Firefox /

Safari, Opera

Cell Phone

CamPro Mobile

Video Player VLC, Quick Time, Real Player, Core Player

1.4 System Requirement

For normal operation and viewing of the network camera, it’s recommended that your

system meets these minimum requirements for proper operation:

Item Requirements

CPU

Inter i5 430M or higher

1. Overview

AirLive SC-300W User’s Manual

6

Note: Please keep updating the latest Windows software and service package.

(Ex: Net Framework, Windows Media Player, Enhance ActiveX Security)

VGA Monitor

ATI Mobility Radeon HD5145 or higher

RAM

2 GB or more

Operating System

Windows VISTA / Windows XP / Windows 7/ Windows 8/

Windows 10

Web Browser

Internet Explorer 8 or later; Apple Safari 2 or above; Firefox

2.00 or above; Google Chrome

2. Package Contents and Installation

AirLive SmartCube 300W User’s Manual

7

2.1 Package Contents

User can find the following items in the package as below:

1. AirLive SmartCube 300W is the main element of the product.

2. UID QR code card

3. Quick Setup Guide.

4. The drill sticker

5. 5V 1A adapter

6. Accessory Package (Screws/ Plastic Anchors)

2.2 WiFi Connections

There are two ways to connect to WiFi.WPS connection or set up the camera by Ethernet

port

2.2.1. WPS connection

1. Click WPS button on the router first.

2

2.

Package Contents and

Installation

2. Package Contents and Installation

AirLive SC-300W User’s Manual

8

2. Click Reset/WPS button on SmartCube 300W then the green led will be on for 2

minutes. When SmartCube 300W connects to the router successfully, the green led will

be flashing.

Note: The WPS function only works when the router is in WPA2 AES security protocols or

has no protected password.

2.2.2. Set up the camera by Ethernet port

1. Please skip this step if your camera has made successful wireless connection to your

router. However, if your wireless router does not have a WPS button. You can configure

the camera by connecting the SmartCube's LAN port to your router's LAN port by

Ethernet cable. Then use your PC or Notebook to setup the camera's WiFi setting.

2. Package Contents and Installation

AirLive SmartCube 300W User’s Manual

9

Note: If you want to connect your PC directly to the camera by Ethernet cable, the IP

camera's default LAN port IP address is 192.168.1.100.

2.2.3. Interface

2. Package Contents and Installation

AirLive SC-300W User’s Manual

10

1. MicroSD Card Slot: MicroSD Card Slot allows you to insert a memory card for local

storage.

2. WPS and Reset Button: Power the camera and push and Hold Reset button for

10seconds .This button is used to restore all the factory default settings. Sometimes,

restarting the device will make the system back to a normal state.

3. Power Input: 5V DC,1A

2.3 Connect to IP Camera

Install the AirLive IP Wizard on your PC.

Please download IP wizard II from AirLive SmartCube 300W support page

http://www.airlive.com/product/SmartCube-300W

2. Package Contents and Installation

AirLive SmartCube 300W User’s Manual

11

2.3.1. Find the Camera using IP Wizard

Install and start the AirLive IP Wizard. The program will automatically search for all cameras

on your network. Double click on the camera you want to configure and the program will

open your web browser to configure the camera.

Important Note: Please make sure you have made Internet Explorer as your default

browser first.

3. Using IP Camera via Web Browser

AirLive SC-300W User’s Manual

12

3.1 Windows Web Browser

1. Open your web browser and enter the IP address or host name of the IP camera in the

Location / Address field of your browser.

2. Use the default account “admin” and default password “airlive”.

Note: The default user name “admin” and the password “airlive” are the default values.

You can change them in the Account Menu. (Please check “System → Account”)

3. You need to install the ActiveX on your PC when you first access to the camera web UI.

3

3.

Using IP Camera via Web

Browser

3. Using IP Camera via Web Browser

AirLive SmartCube 300W User’s Manual

13

4. Configure the camera's wireless setting

On the camera's web UI, please click on the "Configuration" icon to go into the

configuration page. Then click on "Network"->"Wireless" page. Select your wireless

router's SSID and key in the security key. Then click on "Apply" button.

5. Check wireless connection

Please open the AirLive IP Wizard program and click on search icon. You should see 2

"SmartCube 300W" on the list if the camera has made successful wireless connection to

your router. Now, please disconnect the Ethernet cable between the camera and the

router. You should be able to access the camera using wireless connection from now on.

3. Using IP Camera via Web Browser

AirLive SC-300W User’s Manual

14

6. The monitor image will be displayed in your browser. In the left side of main window, you

can configure the settings you want. For more details, please refer to the following

chapters.

5. Operating the Network Camera

AirLive SmartCube 300W User’s Manual

15

4.1 Using AirLive APPCAM via iOS/Android device

When the camera connects to the internet, user can use AirLive APPCAM to connect the

camera.

4.1.1. Download the AirLive APPCAM APP

Please visit App Store or Google Play to download AirLive APPCAM . You can use QR

code scanner software directly or simply search the “AirLive APPCAM”.

4

4.

AirLive APPCAM via

iOS/Android device

Page is loading ...

AirLive SmartCube 300W IP-Camera User guide

AirLive SmartCube 300W IP-Camera User guide

Related papers

Other documents