Autonics PA10-VP User manual

Autonics
Brand
Autonics
Model
PA10-VP
Type
User manual

This manual is also suitable for

Autonics PA10-VP

The Autonics PA10-VP is a high-function controller that can be used for a variety of applications, including detecting labels on glass bottles, synchronizing sensors, and controlling outputs based on input signals.

The PA10-VP has two input channels, IN1 and IN2, which can be configured to accept either PNP or NPN input signals. The input signals can be either normally open or normally closed. The PA10-VP also has two output channels, OUT1 and OUT2, which can be configured to drive either AC or DC loads.

The PA10-VP's operation mode can be selected using the rotary switch on the front panel. The available operation modes are:

Autonics PA10-VP

The Autonics PA10-VP is a high-function controller that can be used for a variety of applications, including detecting labels on glass bottles, synchronizing sensors, and controlling outputs based on input signals.

The PA10-VP has two input channels, IN1 and IN2, which can be configured to accept either PNP or NPN input signals. The input signals can be either normally open or normally closed. The PA10-VP also has two output channels, OUT1 and OUT2, which can be configured to drive either AC or DC loads.

The PA10-VP's operation mode can be selected using the rotary switch on the front panel. The available operation modes are:

SENSOR CONTROLLER
PA10 SERIES
Thank you for choosing our Autonics product.
Please read the following safety considerations before use.
1. Fail-safe device must be installed when using the unit with machinery that may cause serious injury or
substantial economic loss. (e.g. nuclear power control, medical equipment, ships, vehicles, railways, aircraft,
combustion apparatus, safety equipment, crime/disaster prevention devices, etc.)
Failure to follow this instruction may result in re, personal injury, or economic loss.
2. Install on a device panel or DIN rail to use.
Failure to follow this instruction may result in electric shock or re.
3. Do not connect, repair, or inspect the unit while connected to a power source.
Failure to follow this instruction may result in electric shock or re.
4. Check 'Connections' before wiring.
Failure to follow this instruction may result in re.
5. Do not disassemble or modify the unit.
Failure to follow this instruction may result in electric shock or re.
1. When connecting the power/sensor input and relay output, use AWG 24 (0.20mm
2
) to AWG 15 (1.65mm
2
)
cable or over and tighten the terminal screw with a tightening torque of 0.98 to1.18N
.
m.
Use proper cables for the rated load current.
Failure to follow this instruction may result in re or malfunction due to contact failure.
2. Use the unit within the rated specications.
Failure to follow this instruction may result in re or product damage.
3. Use dry cloth to clean the unit, and do not use water or organic solvent.
Failure to follow this instruction may result in electric shock or re.
4. Do not use the unit in the place where ammable/explosive/corrosive gas, humidity, direct sunlight, radiant
heat, vibration, impact, or salinity may be present.
Failure to follow this instruction may result in re or explosion.
5. Keep metal chip, dust, and wire residue from owing into the unit.
Failure to follow this instruction may result in re or product damage.
Warning
Caution
▣ Ordering Information
▣ Input Connections
●
PA10-V/PA10-W
●
PA10-VP/PA10-WP
NPN open
collector type &
NPN universal
output type sensor
PNP open
collector type &
PNP universal
output type sensor
●
PA10-U
NPN open
collector
output
type sensor
Sensor
controller
Sensor
controller
Sensor
controller
+12V
5.6㏀
9.4㏀
5.4㏀
1.8㏀
Main circuit
Main circuit
+12V
IN1, IN2
IN1, IN2
(
(
+12V
⑨, ⑬
⑪ IN1
⑮ IN2
⑩
⑭
IN1, IN2
0V
0V
0V
▣ Specications
Model PA10-U PA10-V PA10-VP PA10-W PA10-WP
Power supply 100-240VAC
ᜠ
50/60Hz
Allowable voltage range
90 to 110% of rated voltage
Power consumption
Max. 10VA (condotion:12VDC/200mA resistive load)
Power for external
sensor
12VDC
ᜡ
±10% approx. 200mA
Input(IN1, IN2)
Selectable NORM/INV.
Selectable OR/AND
operation for IN1, IN2
input. Selection function
for IN2 derivative action.
Selectable NORM/INV.
Operation for IN1, IN2 AND.
Selectable NORM/INV.
Selection function for
IN1, IN2 individual operation.
NPN input type
NPN input type PNP input type NPN input type PNP input type
Input method
●
PA10-U
[No-voltage input] Impedance at short-circuit: Max. 680Ω, Residual voltage at short-
circuit: Max. 0.8V, Impedance at open: Min. 100kΩ
●
PA10-V/PA10-W
[No-voltage input] Impedance at short-circuit: Max. 300Ω, Residual voltage at short-
circuit: Max. 2V, Impedance at open: Min. 100kΩ
●
PA10-VP/PA10-WP
[Voltage input]
Input impedance: 5.6kΩ, "H" level voltage: 5-30VDC
ᜡ
, "L" level voltage: 0-2VDC
Out-
put
Contact output OUT[250VAC
ᜠ
3A(Resistive load)]
OUT1, OUT2 [250VAC
ᜠ
3A(Resistive load)]
Solid-state
output
OᆞC OUT1, OᆞC OUT2
OᆞC OUT
-
NPN open collector output Max. 30VDC
ᜡ
Max. 100mA
Response time Relay output : Max. 10ms, Transistor output : Max. 0.05ms
Time setting
function by
each mode
※Only for
PA10-U
Have
●
ON-DELAY MODE
●
ONE-SHOT DELAY MODE
●
FLICKER ONE-SHOT MODE
●
HIGH-SPEED DETECTION MODE
Non
●
NORMAL MODE
●
FLIP-FLOP MODE
●
ENCODER(MODE 9 to 11)
Relay
life
cycle
Mechanical Min.10,000,000 times
Electrical Min.100,000 times(250VAC 3A resistive load)
Dielectric strength 2000VAC 50/60Hz for 1 minute
Insulation resistance Over 100MΩ(at 500VDC megger)
Envi-
ron
ment
Ambient
temperature
-10 to 55
℃
[Storage: -25 to 60
℃
]
Ambient
humidity
35 to 85%RH [Storage: 35 to 85%RH]
Unit weight Approx. 150g Approx. 160g
▣ Dimensions and Installation Interval
※If the load is connected over 200mA at the sensor output, it may cause mechanical trouble.
※Environment resistance is rated at no freezing or condensation.
▣ Connections
●
PA10-U
●
PA10-V/PA10-VP
●
PA10-W/PA10-WP
~
INV
MADE IN KOREA
NORM
NORM
OUT
IN 1
IN 2
POWER
INV
+12V
PA10-V
GND
CONTACT OUT:
250VAC 3A
RESISTIVE LOAD
!
SOURCE
100-240VAC
50/60Hz
NC
IN2
COM
+12V GND IN1
OᆞC
OUT
NO
8
16
4
7
15
3
6
14
2
1211109
5
13
1
~
SA
INV
INV
AND
SB
SC
SD
T1
T2
O
N
O
N
NORM
OR
M
O
D
E
O
F
F
O
F
F
TIME
A
D
J
MADE IN KOREA
NORM
NORM
OUT2
OUT1
IN 1
IN 2
POWER
+12V
PA10-U
GND
!
SOURCE
100-240VAC
50/60Hz
CONTACT OUT:
250VAC 3A
RESISTIVE LOAD
Brown
Brown
Brown
Brown
Brown
Brown
Blue
Blue Blue
Blue
Blue
Blue
Black
Black Black
Black
BlackBlack
NC
IN2
COM
+12V GND IN1
OᆞC
OUT1
OᆞC
OUT2
NO
8
16
4
7
15
3
6
14
2
1211109
5
13
1
~
INV
MADE IN KOREA
NORM
NORM
OUT1
IN 1
IN 2
POWER
INV
OUT2
+12V
PA10-W
GND
CONTACT OUT1,OUT2:
250VAC 3A
RESISTIVE LOAD
OUT1
OUT2
!
SOURCE
100-240VAC
50/60Hz
NC1
NC2
+12V GND IN1
IN2
COM1
COM2
NO1
NO2
8
16
4
7
15
3
6
14
2
1211109
5
13
1
▣ Front Panel Indentication
●
PA10-U
●
PA10-V/PA10-VP
●
PA10-W/PA10-WP
Timer volume: Adjust time within the range which is set with
9
.
Terminal block
Power indicator : LED turns on when AC power applied
Output indicator 1 : Indication of output 1 operation status
Output indicator 2 : Indication of output 2 operation status
Sensor input indicator : lndication of sensor input signal
(LED turns on when sensor input is Low)
AND/OR selection switch : Select "AND" or "OR" for IN1, IN2 Input
Selection switch of sensor input signal
: (Input signal reverse turn function)
●
NORM : When input signal is low, it is valid signal. ( )
●
INV : When input signal is high, it is valid signal. ( )
Derivative action selection of IN2 input signal (AND/OR selection switch: AND)
: (When input signal is high( ), it is effective signal)
●
NORM : IN2 input signal is operating as reverse turn function
●
:
Derivative action of IN2 input signal. ※See "▣ Derivation action applications"
Selection switch for operation mode: See "▣ Operation mode" in next page.
Selection switch of time range and max. input frequency: It is the switch
to select time range(1 to 7 mode) or allowable input frequency(9 to 11 mode).
INV
NORM
●
Time range: Approx. 0.01 to 0.1sec, Max. input frequency: 100kHz
●
Time range: Approx. 0.1 to 1sec, Max. input frequency: 10kHz
●
Time range: Approx. 0.1 to 10sec, Max. input frequency: 1kHz
●
Time range: Approx. 10 to 100sec, Max. input frequency: 100Hz
T1
T2
O
N
O
F
F
T1
T2
O
N
O
F
F
T2
T1
O
N
O
F
F
T1
T2
O
N
O
F
F
NORM
1
2
3
4
0
!
5
6
7
8
9
PA10-U
IN 1
OUT 1
OUT 2
IN 2
POWER
MADE IN KOREA
9
5
13
1
10
6
14
2
11
7
15
3
12
8
16
4
SA
INV
AND
SB
SC
SD
T1
T2
O
N
O
N
NORM
OR
NORM
M
O
D
E
O
F
F
O
F
F
A
D
J
NORM
INV
+12V
+12V
NC
COM
NO
GND
GND
IN 1
IN 2
OᆞC
OUT1
OᆞC
OUT2
1
2
3
4
0
!
5
6
7
8
9
▣ Derivative Action Applications
◎ Detect label of glass bottle
Brown
Brown
Blue
Blue
Black
Black
~
SA
INV
INV
AND
SB
SC
SD
T1
T2
O
N
O
N
NORM
NORM
NORM
M
O
D
E
O
F
F
OUT2
O
F
F
A
D
J
OUT1
PA10-U
IN 1
IN 2
POWER
MADE IN KOREA
OR
TIME
Output((OUT)
OᆞC
OUT2
OᆞC
OUT1
IN1
(Sensor for detecting
the target)
BEN300-DDT
BEN300-DDT
IN2
(Sensor for
synchroni-
zation)
!
SOURCE
100-240VAC
50/60Hz
12
8
16
4
11
7
15
3
10
6
14
2
9
5
13
1
●
Operation
When IN1 is ON and IN2 is ON, OUT will not work.
But when there is no label on bottle, OUT will work when IN2 is ON. OUT will be returned after setting time.
Note)Condition of detecting label on glass bottle is to install with IN1 operating first.
IN1
(Sensor for
detecting
the target)
Derivative action
OUT (3-4)
OUT1
OᆞC OUT2
(14-16)
OᆞC OUT1
(10-12)
OUT2
IN2
(Sensor for
synchronization)
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Label No label
▣ Factory Default for S/W
●
PA10-U:
MODE1 ON-DELAY
●
PA10-V: NORM
●
PA10-VP: NORM
●
PA10-W: NORM
●
PA10-WP: NORM
PA10-
V
INV
INV
NORM
NORM
POWER
PA10-
W
INV
INV
NORM
NORM
POWER
OUT
IN 1
IN 2
MADE IN KOREA
SA
INV
INV
AND
SB
SC
SD
T1
T2
O
N
O
N
NORM
OR
NORM
NORM
M
O
D
E
O
F
F
OUT2
O
F
F
TIME
A
D
J
OUT1
PA10-U
IN 1
IN 2
POWER
MADE IN KOREA
NORM
OUT2OUT1
IN 1
IN 2
MADE IN KOREA
Item
Function
Input
No mark NPN input
P PNP input
U High function controller
V Controller
W 2 Channel controller
PA10 Multi-function power amplier
PA10
U
●
OFF-DELAY MODE
●
FLICKER MODE
●
LOW-SPEED DETECTION MODE
●
ON/OFF-DELAY MODE
1
2
3
4
5
Power indicator
: LED turns on when
AC power applied.
Output indicator
: Indication of output
signal.
Sensor input indicator
: lndication of sensor
input signal.
●
PA10-V: LED turns on
when sensor input is Low
●
PA10-VP: LED turns on
when sensor input is High
Selection switch of
sensor input signal
●
NORM: When sensor
input signal is Low,
it is vaild signal.
●
INV: When sensor input
signal is High, it is vaild
signal.
Terminal block
※When IN1, IN2 input signal is AND, OUT will work.
PA10-V
9
5
13
1
10
6
14
2
11
7
15
3
12
8
16
4
+12V
+12V
NC
COM
NO
GND
GND
IN 1
IN 2
OᆞC
OUT
3
NORM
OUT
IN 1
IN 2
POWER
MADE IN KOREA
NORM
INV
5
2
4
1
INV
※IN1, IN2 operates individually.
PA10-W
4
NORM
OUT1
IN 1
IN 2
POWER
MADE IN KOREA
NORM
INV
6
2
1
INV
OUT2
5
3
9
5
13
1
10
6
14
2
11
7
15
3
12
8
16
4
+12V
+12V
NC1
NC2
COM1
COM2
NO1
NO2
GND
GND
IN 1
IN 2
Power indicator
: LED turns on when AC
power applied
Output 1 indicator
: Indication of output 1
operation status.
Output 2 indicator
: Indication of output 2
operation status.
Sensor input indicator
: lndication of sensor
input signal.
●
PA10-W: LED turns on
when sensor input is Low.
●
PA10-WP: LED turns on
when sensor input is High.
Selection switch of
sensor input signal
●
NORM: When sensor
input signal is Low,
it is vaild signal.
●
INV: When sensor input
signal is High, it is vaild
signal.
Terminal block
1
2
3
4
5
6
T
Safety Considerations
※
Please observe all safety considerations for safe and proper product operation to avoid hazards.
※
Safety considerations are categorized as follows.
Warning Failure to follow these instructions may result in serious injury or death.
Caution Failure to follow these instructions may result in personal injury or product damage.
※
The symbols used on the product and instruction manual represent the following
symbol represents caution due to special circumstances in which hazards may occur.
(
Unit
: mm)
38
SA
INV
INV
AND
SB
SC
SD
T1
T2
O
N
O
N
NORM
OR
NORM
NORM
M
O
D
E
O
F
F
OUT2
O
F
F
TIME
OUT1
PA10-U
IN 1
IN 2
POWER
MADE IN KOREA
A
D
J
94±0.5
Ø5
35.5
82
76
When installing multiple sensor
controllers, please keep space
between units at least 10mm for
heat radiation.
Min. 10mm
◎ Dimensions ◎ Installation interval
DRW171160AA
※
The above specications are subject to change and some models may be discontinued without notice.
※
Be sure to follow cautions written in the instruction manual and the technical descriptions
(catalog, homepage).
a b
a
b
<Forked>
Min.
3.5mm
Max.
7.0mm
※
Use teminals of size specied below.
I N S T R U C T I O N M A N U A L
▣ Operation Mode
●
MODE 1 ON-DELAY MODE
: OUT will be ON after setting time when one of IN1 and IN2 is ON. When IN1 and IN2 are OFF,
OUT will be OFF. (This is when input logic is OR)
T: Setting time
SA
SB
SC
SD
O
N
M
O
D
E
O
F
F
ON
OFF
IN1
IN2
OUT
ON
OFF
ON
OFF
T
T
●
MODE 2 OFF-DELAY MODE
: OUT will be ON at the same time when IN1 or IN2 is ON then OUT will be OFF after setting time when
IN1 or IN2 is OFF. (This is when input logic is OR)
T: Setting time
SA
SB
SC
SD
O
N
M
O
D
E
O
F
F
ON
OFF
IN1
IN2
OUT
ON
OFF
ON
OFF
T
T
●
MODE 3 ONE-SHOT DELAY MODE
: OUT will be ON at the same time when IN1 or IN2 is ON then OUT will be OFF after setting time.
(This is when input logic is OR)
T: Setting time
SA
SB
SC
SD
O
N
M
O
D
E
O
F
F
ON
OFF
IN1
IN2
OUT
ON
OFF
ON
OFF
T
T
●
MODE 0 NORMAL MODE
: OUT will work according to input signal regardless Timer.
SA
SB
SC
SD
O
N
M
O
D
E
O
F
F
ON
OFF
ON
OFF
IN1 IN1
<OR function> <AND function>
IN2 IN2
OUT OUT
※Output will be ON when either
IN1 or IN2 is ON.
※Output will be ON when both
IN1 and IN2 are ON.
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Note) In case of One-Shot
Mode, it is not diffe-
rent between
S/W se-
lections.
AND
OR
Note)ON/OFF rate of
Flicker output is 1:1.
Note) In case of Flicker Mode,
it is not different
between
and S/W.
AND
OR
NORM
●MODE 4,5 FLICKER MODE / FLICKER ONE-SHOT MODE
: OUT will be ON after setting time for IN1 input then it is ickering and OUT will be ickering after setting
time from ON and IN2 input is same. Incase One-shot Mode, output time(Ts) will be selected by S/W.
( : Ts= Approx. 10ms, : Ts= Approx. 100ms)
NORM
SA
SB
SC
SD
O
N
M
O
D
E
O
F
F
※T : Setting time, Ts : One-Shot output time
ON
OFF
IN1
IN2
T
T T T T T T T T T T T
Ts Ts Ts Ts Ts Ts
T T T T T T T T T T
MODE 4
OUT
MODE 5
OUT
ON
OFF
ON
OFF
ON
OFF
SA
SB
SC
SD
O
N
M
O
D
E
O
F
F
TIME S/W Max. input frequency Output pulse width(Tw)
Input speed of connected equipment(cps)
100kHz Approx. 0.5㎲ Min. 2000kHz(2,000kcps)
10kHz Approx. 5㎲ Min. 200kHz(200kcps)
1kHz Approx. 50㎲ Min. 20kHz(20kcps)
100Hz
Approx. 500㎲ Min. 2kHz(2kcps)
T1
T2
O
N
O
F
F
T1
T2
O
N
O
F
F
T1
T2
O
N
O
F
F
T1
T2
O
N
O
F
F
◎TIME S/W function in Encoder mode
: TIME S/W is to convert output pulse width(Tw).
MODE 1 to MODE 7, MODE 12
MODE 6 to MODE 7
Setting time range Input frequency rpm
0.01 to 0.1sec 100 to 10Hz 6,000 to 600rpm
0.1 to 1sec 10 to 1Hz 600 to 60rpm
1 to 10sec 1 to 0.1Hz 60 to 6rpm
10 to 100sec 0.1 to 0.01Hz 6 to 0.6rpm
◎TIME S/W function(MODE 1 to MODE 7)
: Set the setting time by TIME S/W(T1, T2) and front TIME VOLUME(ADJ).
MODE
TIME S/W
※Range of operating rpm is 1 pulse per 1 revolution.
※When the pulse is increasing per 1 revolution, range of operating rpm is decreasing.
T1
T2
O
N
O
F
F
T1
T2
O
N
O
F
F
T1
T2
O
N
O
F
F
T1
T2
O
N
O
F
F
●
MODE 8 Flip-Flop MODE [OUT LATCH operation]
: When IN1 signal is input then the Flip-Flop output will be ON(SET). When the IN2 signal is input,
Flip-Flop Signal will be OFF(RESET).
Note)IN2 will be the first of input signal.
Note)It is not different between and S/W.
Note)There is no Timer function in Flip-Flop Mode, therefore use this unit with Time S/W(T1, T2) as OFF.
ANDOR
NORM
ON
OFF
IN1
IN2
OUT
ON
OFF
ON
OFF
SA
SB
SC
SD
O
N
M
O
D
E
O
F
F
◎ENCODER MODE(MODE 9 ~ MODE 11)
1) There should be 90°phase difference between IN1 and IN2 for input terminal.
2) Please connect A phase output of encoder to IN1 and B phase output of encoder to IN2, when use
NPN open collector or Totempole output type of encoder with controller.
In this case, turnded to CW direction detection signal(O.C OUT2, OUT) output of controller will be OFF.
3) There are output function of pulse(O.C OUT1) which has been multiplied(×1, ×2, ×4 times) against
input signal and direction detection output(O.C OUT2, OUT) function which detects direction of
encoder rotation in Encoder mode.
4) Be sure to Input speed(cps) of connected equipment because pulse width of O.C OUT1 is short.
5) Selection S/W can be set at any position.
ANDOR
NORM
NORM
INV
●
MODE 9 ENCODER
(Input pulse×1time)
●
MODE 10 ENCODER
(Input pulse×2times)
●
MODE 11 ENCODER
(Input pulse×4times)
SA
SB
SC
SD
O
N
M
O
D
E
O
F
F
SA
SB
SC
SD
O
N
M
O
D
E
O
F
F
SA
SB
SC
SD
O
N
M
O
D
E
O
F
F
MODE 9
Input pulse
X 1
MODE 10
Input pulse
X 2
MODE 11
Input pulse
X 4
Direction
detection output
ON
OFF
IN1
(A phase)
IN2
(B phase
OᆞC
OUT1
OᆞC
OUT1
OᆞC
OUT1
OᆞC
OUT2
(OUT)
※Note)Tw(pulse width) can be changed according to max. input frequency.
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
CCWCW
Tw
1. Follow instructions in 'Cautions during Use'. Otherwise, it may cause unexpected accidents.
2. Use the product, 0.1 sec after supplying power.
3. When supplying or turning off the power, use a switch or etc. to avoid chattering.
4. Install a power switch or circuit breaker in the easily accessible place for supplying or disconnecting the power.
5. Keep away from high voltage lines or power lines to prevent inductive noise.
In case installing power line and input signal line closely, use line lter or varistor at power line and shielded wire at
input signal line.
Do not use near the equipment which generates strong magnetic force or high frequency noise.
6. This unit may be used in the following environments.
①
Indoors (in the environment condition rated in 'Specications')
②
Altitude max. 2,000m
③
Pollution degree 2
④
Installation category II
▣ Cautions during Use
▣ Output
It is able to reduce noise generating if install surge obsorber between inductive loads(Motor, Solenoid, etc) as Picture 1.
When use DC Relay for load, please install a diode at relay coils as Picture 2. (Be sure to power polarity)
(Picture 1) Relay output
s
d
f
~
SOURCE
※
※Surge obsorber (Load: 22Ω,
condenser: 0.1㎌, voltage: 630V)
NO
NC
COM
PA10 Series
(Picture 2) NPN open collector output
12
10
+
-
DC POWER
※
※Max. resisting pressure must be more than three
times of load voltage. Current capacity: 1A
PA10 Series
▣ Function Diagram
●
PA10-U
●
MODE 7 HIGH-SPEED DETECTION MODE
: OUT will be ON when input signal (IN1) is shorter than setting time by comparing it to to the setting
time by one cycle.
Note)Above is when input logic is OR and it will be the same by using IN2 input signal terminal instead
of IN1.
SA
SB
SC
SD
O
N
M
O
D
E
O
F
F
Progressing time
IN1
(IN2)
OUT
ON
OFF
ON
OFF
TIME
Setting
time
Note)Above is when input logic is OR and it will be the same by using IN2 input signal terminal instead
of IN1.
Note)When use MODE 6 as above, be sure that OUT will be work at the same time with power supply.
SA
SB
SC
SD
O
N
M
O
D
E
O
F
F
●
MODE 6 LOW-SPEED DETECTION MODE
: OUT will be ON when input signal (IN1) is longer than setting time by comparing it to to the setting
time by one cycle.
IN1
(IN2)
TIME
Setting
time
OUT
Progressing time
ON
OFF
ON
OFF
+5V
NORM
NORM
NORM
INV
INV
IN1 input indicator
IN1
IN2
IN2 input indicator
AND
OR
(Derivative)
MODE S/W
Control
box
OUT2 output indicator
OUT1 output indicator
OᆞC
OUT1
OᆞC
OUT2
OUT
+12V
●
PA10-V/PA10-VP
IN1 input indicator
※Add when it is PNP input
IN2 input indicator
OUT output indicator
NORM
NORM
INV
INV
IN1
IN2
OᆞC
OUT
OUT
+12V
+12V
+12V
●
PA10-W/PA10-WP
+12V
※Add when it is PNP input
IN1 input indicator
IN2 input indicator
OUT2 output indicator
OUT1 output indicator
NORM
NORM
INV
INV
IN1
IN2
OUT1
OUT2
+12V
+12V
+12V
●
MODE 12 ON/OFF-DELAY MODE
: OUT will be ON after setting time when IN1 (or IN2) is ON. When IN1 (or IN2) is OFF, OUT will be OFF
after setting time. (This is when input logic is OR)
※If IN1 (or IN2) ON/OFF time is shorter than setting time, OUT does not turn.
T: Setting time
SA
SB
SC
SD
O
N
M
O
D
E
O
F
F
(IN2)
ON
OFF
IN1
T
TTT
OUT
ON
OFF
NORM
Major Products
http://www.autonics.com
HEADQUARTERS:
18, Bansong-ro 513beon-gil, Haeundae-gu, Busan,
South Korea, 48002
TEL: 82-51-519-3232
E-mail: [email protected]
DRW171160AA
Photoelectric Sensors Temperature Controllers
Fiber Optic Sensors Temperature/Humidity Transducers
Door Sensors SSRs/Power Controllers
Door Side Sensors Counters
Area Sensors Timers
Proximity Sensors Panel Meters
Pressure Sensors Tachometer/Pulse (Rate) Meters
Rotary Encoders Display Units
Connector/Sockets Sensor Controllers
Switching Mode Power Supplies
Control Switches/Lamps/Buzzers
I/O Terminal Blocks & Cables
Stepper Motors/Drivers/Motion Controllers
Graphic/Logic Panels
Field Network Devices
Laser Marking System (Fiber, Co
₂
, Nd: YAG)
Laser Welding/Cutting System
  • Page 1 1
  • Page 2 2

Autonics PA10-VP User manual

Autonics
Brand
Autonics
Model
PA10-VP
Type
User manual
This manual is also suitable for

Autonics PA10-VP

The Autonics PA10-VP is a high-function controller that can be used for a variety of applications, including detecting labels on glass bottles, synchronizing sensors, and controlling outputs based on input signals.

The PA10-VP has two input channels, IN1 and IN2, which can be configured to accept either PNP or NPN input signals. The input signals can be either normally open or normally closed. The PA10-VP also has two output channels, OUT1 and OUT2, which can be configured to drive either AC or DC loads.

The PA10-VP's operation mode can be selected using the rotary switch on the front panel. The available operation modes are:

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents