Wren Kitchens 600 Microwave Wall Unit Assembly Guide

Category
Wall & ceiling mounts accessories
Type
Assembly Guide
For Internal Use:FI.WR.INS.056_WKIN00123_WALL720_600MW_Rev2.indd
WALL UNIT
600 Microwave
Assembly Guide
For Internal Use:FI.WR.INS.056_WKIN00123_WALL720_600MW_Rev2.indd
Page 1
WALL UNIT
600 Microwave
Assembly Guide
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED
Panel A
x1 Back Panel
Hanging Bracket
x2 Inc Screws
(F) x12
Wooden Dowel
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
(G) x12
Cam Dowel
(Expanding)
(H) x12
Cam Lock
(K) x6
30mm
Screw
(S) x4
20mm
Screw
(L) x2
15mm
Screw
(M) x4
Cover Cap
(N) x1
Door
Buer
(FF) x2
Small
L Bracket
(T) x4
Back Panel
Support Clip
Hanging Bracket Plate
x2 (Screws Not Included)
Hinge Mounting Plate
x2 Inc Screws
Hinge
x2 Inc Screws
Hanging Bracket
Cover Cap x2
Lift Hinge
x2 inc. Screws
Panel B
x2 End Panel
Panel C
x3 Base Panel
Frontal
(packed separately) x1
WALL UNIT
600 Microwave
Assembly Guide
For Internal Use:FI.WR.INS.056_WKIN00123_WALL720_600MW_Rev2.indd
Page 2
Step 1.
Seat dowel (F) into holes in
end panel (B) as shown.
Step 2.
Seat cam dowel (G) into holes
in end panel (B) as shown.
Step 3.
Attach panels x3 (C)
to panel (B),using cam
dowels (G)& cam locks (H)
(in blue), and also using
dowels (F) (in orange)
in positions as shown.
Step 4.
Slide panel (A) into the groove
of panel (B).
Step 5.
Insert cam lock (H).
Hand tighten all cam locks (H),
this will expand the
cam dowels (G) and tighten
the unit together.
All Cam Locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening.
Do not use power tools with
cam dowel (G) or cam lock (H)
B
A
C
C
C
Seat (G)
cam dowel
into hole as
shown.
Dowel (F)
& Cam Dowel (G)
location detail
G
F
F G
B
G
F
F G
B
B
C
C
H
H
G
G
View from underside View from underside
For Internal Use:FI.WR.INS.056_WKIN00123_WALL720_600MW_Rev2.indd
Page 3
WALL UNIT
600 Microwave
Assembly Guide
Step 9.
Insert cam lock (H).
Hand tighten all cam locks (H),
this will expand the
cam dowels (G) and
tighten the unit together.
Do not use power tools with
cam dowel (G) or cam lock (H)
B
B
A
C
C
C
All Cam Locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening.
Step 6.
Seat dowel (F) into holes in
end panel (B) as shown.
Step 7.
Seat cam dowel (G) into holes
in end panel (B) as shown.
Step 8.
Attach panel (B) to
panels x 3 (C),using cam
dowels (G)& cam locks (H)
(in blue), and also using
dowels (F) (in orange)
in positions as shown.
B
B
C
C
H
H
G
G
Seat (G)
cam dowel
into hole as
shown.
View from underside View from underside
Dowel (F)
& Cam Dowel (G)
location detail
G
G
F
F
F
F
G
G
B
WALL UNIT
600 Microwave
Assembly Guide
For Internal Use:FI.WR.INS.056_WKIN00123_WALL720_600MW_Rev2.indd
Page 4
B B
C
TOP FIXED SHELF
LEFT HAND RIGHT HAND
Step 10.
Ensure carcase is square.
Secure Back Panel (A) with
4 x Screws (K) as shown.
Ensure you screw into
centres of Panel (C) 9mm
from the edge
Step 11.
Slide the back panel
clips (T) into the groove
of both panels (B) & (C).
The back panel clips (T)
should be evenly spaced as
shown and positioned to
allow the hanging bracket
and corner gussets to be
tted.Onceinplace,
tighten screw.
A
B
T
T
T
T
T
A
B
T
Step 12.
Secure Small L Bracket (FF)
to bottom left and
right of wall unit using
1 x 15mm screws (L)
per plate, as shown.
L
L
FF
FF
A
B
K
K
K
K
9mm
9mm
Step 13.
Measure and attach
Hinge Mounting Plate onto
xedshelf(C) as shown,
using Screws which are
already positioned within
the Hinge Plates.
192 192
160 160
Top Top
Front
Front Front
37 37
Left Right94 94126 126
Front
37 37
B
B
C
Removed from lift hinge
Hinge Plates
Step 14.
Measure and attach lift hinge bracket with
2 x screw per bracket. The required screws
are included inside lift hinge pack.
For Internal Use:FI.WR.INS.056_WKIN00123_WALL720_600MW_Rev2.indd
Page 5
WALL UNIT
600 Microwave
Assembly Guide
Step 16.
Measure appropriately and attach the 2 x hanging bracket plates
onto the wall screwing through the provided holes into your wall.
Screws for xing to walls are not provided as these vary
depending on your wall material and construction. Ensure
appropriate xings for wall construction are used.
Step 17.
Hang the cabinet using
the brackets to hook
onto the plate as shown
A
Step 18.
Secure to the wall
using 1 x appropriate
screw through each
L Brackets (FF).
Screws for xing to walls are not provided as these vary
depending on your wall material and construction.
Ensure appropriate xings for wall construction are used.
Step a
Insert Hanging
Bracket into pre-drilled holes
Step 15. Hanging Brackets steps a,b & c to be carried
out on both sides as shown
Step c
Secure with provided
2 x 20mm screws (S) per bracket
Step b
Rotate locking
lever 180 degrees
S
S
Detail A
Detail A
Detail A
Hanging Bracket
Plate
WALL UNIT
600 Microwave
Assembly Guide
For Internal Use:FI.WR.INS.056_WKIN00123_WALL720_600MW_Rev2.indd
Page 6
Step 19.
Using points a, b & c adjust the Cabinet to suit.
Step 20.
Screw into any side units using the
provided 2x 30mm screws (K) to
secure the unit. Place a cover cap on
the head to conceal it.
Step a.
Rotate the screw clockwise
to move the cabinet up.
Anti-clockwise for down.
Step b.
Adjust the depth
using centre
screw.
Step c.
Screw the red screw until it
touches the plate to lock
in position.
Removed from lift hinge
Step 23.
Secure hinges by tightening
2 x screws with hinge dowels
attached. These are already
positioned within the hinges.
Step 22.
Insert hinges into holes as shown.
142142
110 110
BackBack
Left
Right
3030
FRONTAL
Hanging
Bracket
viewed though
Back Panel
C
a
b
b
c
a
Step 21.
Measure and attach lift hinge bracket to frontal with 2 x screw per
bracket. The required screws are included inside lift hinge pack.
K
For Internal Use:FI.WR.INS.056_WKIN00123_WALL720_600MW_Rev2.indd
Page 7
WALL UNIT
600 Microwave
Assembly Guide
Step 24.
Clip hinges into hinge
mounting plates on the unit.
Step 25.
Clip lift hinge mechanisms into
each bracket.
Hinge Cover Caps
Step 27.
Fit cover caps to hinge.
Step 26.
Use a 4mm allen key to adjust
the strength of the lift hinge
for the door weight.
To adjust hinge using a screw
driver, tighten or loosen as
required at points 1 & 2.
Point 1 - up - down
Point 2 - side - side
1
2
FRONTAL HINGE
ADJUSTMENT
View from Inside of Carcase
To release door,
pull catch as shown,
to release hinge from
the hinge plate.
The left and right hinges MUST be
adjusted to the SAME STRENGTH.
The top and bottom
hinges MUST be
adjusted to the SAME
STRENGTH.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Wren Kitchens 600 Microwave Wall Unit Assembly Guide

Category
Wall & ceiling mounts accessories
Type
Assembly Guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI