Auxiliary Relay Module
Installation Guide
©2015 EMS Security Group Ltd. All rights reserved Page 1 of 2 TSD058 Iss 11 21/02/2017 AJM
3 Remove Cable Entry Points
4 Fix Back Box to Wall
AUXILIARY RELAY MODULE
FC-620-001
WARNING
Hazardous
voltage
ident
EXPAN 1 EXPAN 2
3VDC
SET
RST
3VDC
SET
RST
MAINS IN 1 MAINS OUT 1 MAINS IN 2 MAINS OUT 2
L
N
L
N
N/O
N/C
N
LIVE
N/O
N/C
N
LIVE
FC-620-001 Auxiliary Relay Module
Compatible with:
FC-610-001.
1 Warning
2 Components
Part No Product Description
Installation must conform to applicable local
installation codes and should only be installed by a
fully trained competent person.
Isolate mains supply before starting work.
Check all connections. Improper wiring can lead to damage to
this device and cause injury to the user.
Ensure the supply circuit provides adequate fuse or circuit
breaker protection, in accordance with the circuits current
rating.
!
L
N
L
N
LIVE LIVE
N/O
N/C
N
N/O
N/C
N
4x Lid Fixing Screws Front Lid Back Box
3
2
1
= Available Cable
Entry Points
L
N
L
N
LIVE LIVE
N/O
N/C
N
N/O
N/C
N
Drill the cable entry
points as necessary.
Use all three circled fixing
positions to ensure a firm
fixing.
Use suitable fasteners and
fixings.
5 Device Wiring
OUTPUT 2OUTPUT 1
3VDC
SET
RST
INPUT 1 INPUT 2
N/O COM N/C
IP- IP+ IP- IP+
N/O COM N/C
EXPAN1
EXPAN2
3VDC
SET
RST
ident
EXPAN 1 EXPAN 2
3VDC
SET
RST
3VDC
SET
RST
MAINS IN 1 MAINS OUT 1 MAINS IN 2 MAINS OUT 2
L
N
L
N
N/O
N/C
N
LIVE
N/O
N/C
N
LIVE
I/O Unit
PCB
Connections
OUTPUT 2OUTPUT 1
3VDC
SET
RST
INPUT 1 INPUT 2
N/O COM N/C
IP- IP+ IP- IP+
N/O COM N/C
EXPAN
EXPAN
3VDC
SET
RST
ident
EXPAN 1 EXPAN 2
3VDC
SET
RST
3VDC
SET
RST
MAINS IN 1 MAINS OUT 1 MAINS IN 2 MAINS OUT 2
L
N
L
N
N/O
N/C
N
LIVE
N/O
N/C
N
LIVE
I/O Unit
PCB
Connections
The Auxiliary Relay Module requires connection to a FireCell
Input/Output (I/O) Unit.
Two relay outputs are available. These are shown in Figure 2.
The relay outputs are each capable of switching voltages as
specified in the Technical Specification Section of this
document.
230Vac
Supply
Switched
Mains
Out
ARM
I/O Unit
Earth(Green/Yellow)
Live(Brown)
Neutral(Blue)
Neutral(Blue)
Live(Brown)
Earth(Green/Yellow)
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
SENSITIVE
32
1
Operating
Temperature -10°C to 55°C
Storage
temperature 5°C to 30°C
Humidity 0 to 95% non-condensing
Power
requirements 230Vac supply
Trigger voltage 2.8 to 5Vdc
Output rating 3.15A @ 250Vac 50Hz
Output fuse
rating 3.15A (ceramic 5mm x 20mm sand filled type)
Dimensions 160mm (W) 160mm (H) 53mm (D)
Location Type A: For indoor use
Page 2 of 2
6 Output Operation
The Auxiliary Relay Modules relays operate in conjunction with
the connected I/O Units relay operation.
FireCell I/O Unit FireCell Auxiliary Relay Module
Output not activated
Output activated
N/O Output on Mains Out will have no voltage present.
N/C Output on Mains Out will have 230Vac present.
N/O Output on Mains Out will have 230Vac present.
N/C Output on Mains Out will have no voltage present.
Mains Out 1 follows the operation of the I/O Unit’s Output 1.
Mains Out 2 follows the operation of the I/O Unit’s Output 2.
EMS Security Group Ltd. Technology House, Herne
Bay, Kent, CT6 8JZ, United Kingdom
Manufacturer
Year of
manufacture See devices serial number label
2012/19/EU (WEEE directive):
Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the
European Union. For recycling, return this product
to your local supplier upon purchase of equivalent
new equipment, or dispose of it at designated
collection points.
For more information see www.recyclethis.info
EN60950-1:2006+A12:2011 - Incorporating
corrigenda June 2006, August 2006, September
2010, August 2011, October 2011 and August
2012. Information technology equipment - Safety.
Part 1: General requirements.
Complies with
Specification Regulatory Information
/
