Panasonic CQ-VD7003U Installation guide

Brand: Panasonic

Model: CQ-VD7003U

Type: Installation guide

CQ-VD7003U

English

Safety Information

CAUTION:

• PLEASE FOLLOW THE LAWS AND REGULATIONS

OF YOUR STATE, PROVINCE OR COUNTRY FOR

INSTALLATION OF THE UNIT.

• TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK OR PRODUCT DAMAGE, DO NOT EXPOSE

THIS APPLIANCE TO RAIN, SPLASHING, DRIP-

PING OR MOISTURE.

The following applies only in the U.S.A.

Part 15 of the FCC Rules

FCC Warning:

Any unauthorized changes or modifications to this

equipment would void the user's authority to operate

this device.

WARNING

• This installation information is designed

for professional installers with knowledge

of automobile electrical safety systems

and is not intended for non-technical, do-

it-yourself individuals. It does not contain

instructions on the electrical installation

and avoidance of potential harm to air

bag, anti-theft and ABS braking or other

systems necessary to install this product.

Any attempt to install this product in a

motor vehicle by anyone other than a pro-

fessional installer could cause damage to

the electrical safety system and could

result in serious personal injury or death.

• If your car is equipped with air bag and/or

anti-theft systems, specific procedures

may be required for connection and dis-

connection of the battery to install this

product.

Before attempting installation of this elec-

tronic component against the manufactur-

er's recommendation, you must contact

your car dealer or manufacturer to deter-

mine the required procedure and strictly

follow their instructions.

FAILURE TO FOLLOW THE PROCEDURE

MAY RESULT IN THE UNINTENDED

DEPLOYMENT OF AIR BAGS OR ACTIVA-

TION OF THE ANTI-THEFT SYSTEM

RESULTING IN DAMAGE TO THE VEHICLE

AND PERSONAL INJURY OR DEATH.

• TO REDUCE THE RISK FOR FIRE OR ELEC-

TRIC SHOCK AND ANNOYING INTERFER-

ENCE, USE ONLY THE INCLUDED COMPO-

NENTS.

• This unit operates with a 12 V DC negative

ground auto battery system only. Do not

attempt to use it any other system.

• Do not expose the unit to the direct sun-

light or excessive heat.

CQ-VD7003U

English

Upgrade Options

Safety Information................................................2

Upgrade Options ..................................................3

Contents................................................................3

Installation Guide .................................................4

Electrical Connections ......................................14

Contents

Display Unit

CQ-VD7003U

Expansion Module

(CY-EM100U, option)

Hands-Free Kit featuring

Bluetooth

technology

(CY-BT100U, option)

XM Satellite Radio receiver

(XMD1000)

CD Changer

(CX-DP880, option)

DVD Changer

(CX-DH801U, option)

TV Tuner

(CY-TUN153U)

Sirius Satellite Radio receiver

(SIR-PAN1)

Headrest Monitor

(CY-V7100U, option)

iPod

CQ-VD7003U

English

Installation Guide

WARNING

❐ This installation information is designed for professional installers with knowledge

of automobile electrical safety systems and is not intended for non-technical, do-it-

yourself individuals. It does not contain instructions on the electrical installation and

avoidance of potential harm to air bag, anti-theft and ABS braking or other systems

necessary to install this product.

Any attempt to install this product in a motor vehicle by anyone other than a profes-

sional installer could cause damage to the electrical safety system and could result

in serious personal injury or death.

❐ If your car is equipped with air bag and/or anti-theft systems, specific procedures

may be required for connection and disconnection of the battery to install this product.

Before attempting installation of this electronic component against the manufactur-

er's recommendation, you must contact your car dealer or manufacturer to deter-

mine the required procedure and strictly follow their instructions.

FAILURE TO FOLLOW THE PROCEDURE MAY RESULT IN THE UNINTENDED DEPLOY-

MENT OF AIR BAGS OR ACTIVATION OF THE ANTI-THEFT SYSTEM RESULTING IN

DAMAGE TO THE VEHICLE AND PERSONAL INJURY OR DEATH.

❏ Overview

This product should be installed by a professional.

However, should you decide to install the product against

the manufacturer’s recommendation, these operating

Instructions do not contain electrical installation instruc-

tions. You must contact your car dealer or manufacturer

for electrical connection instructions to avoid possible

damage to your electrical safety systems and resulting

injury or death. (Please refer to the “WARNING” state-

ment above).

Your next step is to decide where to install the unit. The

instructions in these pages will guide you through the

remaining steps:

¡Identify and label the car wires.

¡Connect the car wires to the wires of the power con-

nector.

¡Install the unit.

¡Check the operation of the unit.

If you encounter problems, please consult your nearest

professional installer.

Warning

¡This unit operates with a 12 V DC negative ground

auto battery system only. Do not attempt to use it

with any other system. Doing so could cause seri-

ous damage.

Before you begin installation, look for the following items

which are packed with your unit.

¡Operating Instructions (including “Limited Warranty”

and “Customer Service Directory”).

¡Installation Hardware .....Needed for Installation.

CQ-VD7003U

English

❏ Installation Hardware

(For Installation)

❏ Installation Hardware

(For

Wiring)

Note:

¡The number in parenthesis underneath each accessory

part name is the part number for maintenance and serv-

ice.

¡Accessories and their parts numbers are subject to

modification without prior notice due to improvements.

¡Use the supplied screws for installation exclusively. In

case of losing any of them, please order the specific

screw.

Qty.DiagramItemNo.

Trim Plate

Mounting Collar

Mounting Spring

Qty.DiagramItemNo.

Reverse Extension Cord

Rear Support Strap

Round Head Screw

(5 mmø x 6 mm)

Flat-Head Screw

(5 mmø x 6 mm)

Round Head Screw

(4 mmø x 3 mm)

Mounting Bolt (5 mmø)

Tapping Screw

mmø x 16 mm)

Hex. Nut (5 mmø)

Spacer

Double-Faced Adhesive Tape

set

Power Connector

Clip Connector

CQ-VD7003U

English

Installation Guide (continued)

❏ Before Installation

Warning

¡Do not install the monitor in a location which

obstructs driving, visibility or which is prohibited

by applicable laws and regulations. If the monitor

is installed in a location which obstructs forward

visibility or operation of the air bag or other safety

equipment or which interferes with operation of the

car, it may cause an accident.

¡Never use bolts or nuts from the car's safety

devices for installation. If bolts or nuts from the

steering wheel, brakes or other safety devices are

used for installation of the monitor, it may cause an

accident.

¡Attach the wires correctly. If the wiring is not cor-

rectly performed, it may cause a fire or an accident.

In particular, be sure to run and secure the lead

wire so that it does not get tangled with a screw or

the moving portion of a seat rail.

¡Use with 12 V DC negative ground car. This unit is

only for use with a 12 V DC negative ground car. It

cannot be used in large trucks or diesel cars which

are 24 V DC cars. If it is used in the wrong type of

car, it may cause a fire or an accident.

❏ Required Tools

You’ll need a screwdriver and the following:

12 V DC

Test Bulb

Electrical

Tape

Side-Cut

Pliers

Caution

¡Use the specified fuse. Be sure to always use the

specified fuse. If a fuse other than the specified

fuse is used, it may cause a fire or an accident.

¡Do not damage the cord by pinching or pulling it.

Do not pull or damage the cord. If the cord is not

treated properly, it will short out or be severed

and may cause a fire or an accident.

❏ Dashboard Specifications

❏ Identify All Leads

The first step in installation is to identify all the car wires

you’ll use when hooking up your LCD monitor.

As you identify each wire, we suggest that you label it

using masking tape and a permanent marker. This will

help avoid confusion when making connections later.

Note:

¡Do not connect the power connector to the display

unit until you have made all connections. If there

are no plastic caps on the hooking wires, insulate

all exposed leads with electrical tape until you are

ready to use them. Identify the leads in the follow-

ing order.

Power Lead

If your car has a radio or is pre-wired for one:

Cut the connector wires one at a time from the plug

(leaving the leads as long as possible) so that you can

work with individual leads. Turn the ignition on to the

accessory position, and ground one lead of the test bulb

to the chassis.

Touch the other lead of the test bulb to each of the

exposed wires from the cut radio connector plug. Touch

one wire at a time until you find the outlet that causes the

test bulb to light.

Now turn the ignition off and then on. If the bulb also

turns off and on, that outlet is the car power lead.

If your car is not wired for an audio unit:

Go to the fuse block and find the fuse port for radio

(RADIO) accessory (ACC) or ignition (IGN).

THICKNESS

MIN. 4.75 mm {3/16”}

MAX. 5.56 mm {7/32”}

53 mm {2-3/32”}

182 mm {7-5/32”}

CQ-VD7003U

English

Battery Lead

If your stereo unit has a yellow lead, you will need to

locate the car's battery lead. Otherwise you may ignore

this procedure. (The yellow battery lead provides contin-

uous power to maintain a clock or other functions.)

If your car has a radio or is pre-wired for one:

With the ignition and headlights off, identify the car bat-

tery lead by grounding one lead of the test bulb to the

chassis and checking the remaining exposed wires from

the cut radio connector plug.

If your car is not wired for an audio unit:

Go to the fuse block and find the fuse port for the battery,

usually marked BAT.

Speakers (not supplied)

Identify the car speaker leads. There are two leads for

each speaker, usually color coded.

A handy way to identify the speaker leads and the speak-

er they are connected with is to test the leads using a 1.5

V AA battery as follows.

Hold one lead against one pole of the battery and stroke

the other lead across the other pole. You will hear a

scraping sound in a speaker if you are holding a speaker

lead.

If not, keep testing different lead combinations until you

have located all the speaker leads. When you label them,

include the speaker location for each.

❏ Connect All Leads

Now that you have identified all the wires in the car,

you're ready to begin connecting them to the LCD moni-

tor wires. Electrical Connections (a page 14-23) shows

the proper connections and color coding of the leads.

We strongly recommend that you test the unit before

making a final installation.

You can set the unit on the floor and make temporary

connections to test the unit. Use electrical tape to cover

all exposed wires.

Important: Connect the red power lead last, after you

have made and insulated all other connections.

Ground

Connect the black ground lead of the power connector to

the metal car chassis.

Speakers

Connect the speaker wires. See the wiring diagram for

the proper hookups. Follow the diagram carefully to

avoid damaging the speakers and the stereo unit.

The speakers used must be able to handle more than 50

W of audio power. If using optional audio power, the

speakers should be able to handle the maximum amplifier

output power. Speakers with low input ratings can be

damaged.

Speaker impedance should measure 4 – 8 Ω, which is

typically marked on most speakers. Lower or higher

impedance speakers will affect output and can cause

both speaker and stereo unit damage.

Battery

Connect the yellow battery lead to the correct radio wire

or to the battery fuse port on the fuse block.

Equipment

Connect any optional equipment according to the instruc-

tions furnished with the equipment. Read the operating

and installation instructions of any equipment you will

connect to this unit.

Power

Connect the red power lead to the correct car radio wire

or to the appropriate fuse port on the fuse block.

If the LCD monitor functions properly with all these con-

nections made, disconnect the wires and proceed to the

final installation.

❏ Final Installation

Lead Connections

Connect all wires, making sure that each connection is

insulated and secure. Bundle all loose wires and fasten

them with tape so they will not fall down later. Now insert

the LCD monitor into the mounting collar.

Congratulations! After making a few final checks, you’re

ready to enjoy your new LCD monitor.

Caution

¡Never ground the speaker cords. For example, do

not use a chassis ground system or a three-wire

speaker common system. Each speaker must be

connected separately using parallel insulated

wires. If in doubt about how your car’s speakers

are wired, please consult with your nearest pro-

fessional installer.

CQ-VD7003U

English

Installation Guide (continued)

❏ Final Checks

1. Make sure that all wires are properly connected

and insulated.

2. Make sure that the LCD monitor is securely held in

the mounting collar.

3. Turn on the ignition to check the unit for proper

operation.

If you have difficulties, consult your nearest authorized

professional installer for assistance.

❏ Precautions

¡Disconnect the cable from the negative (–) battery ter-

minal (see caution at right).

¡Unit should be installed in a horizontal position with

the front end up at a convenient angle, but less than

30°.

Warning

¡If your car is equipped with air bag and/or anti-

theft systems, specific procedures may be

required for connection and disconnection of the

battery to install this product.

Before attempting installation of this electronic

component against the manufacturer's recom-

mendation, you must contact your car dealer or

manufacturer to determine the required proce-

dure and strictly follow their instructions.

FAILURE TO FOLLOW THE PROCEDURE MAY

RESULT IN THE UNINTENDED DEPLOYMENT OF

AIR BAGS OR ACTIVATION OF THE ANTI-THEFT

SYSTEM RESULTING IN DAMAGE TO THE VEHI-

CLE AND PERSONAL INJURY OR DEATH.

Caution

¡We strongly recommend that you wear gloves for

installation work to protect yourself from injuries.

¡When bending the mounting tab of the mounting

collar with a screwdriver, be careful not to injure

your hands and fingers.

This unit should be professionally installed. In case of

difficulty, please consult with your nearest professional

installer.

1. This unit only operates in a 12 V DC negative ground

system.

2. Follow the Electrical Connections carefully (a page

14-23). Failure to do so may result in damage to the

unit.

3. Connect the power lead after all other connections are

made.

4. Be sure to connect the battery lead (yellow) to the pos-

itive terminal (+) of the battery or fuse block (BAT) ter-

minal.

5. Insulate all exposed wires to prevent short circuiting.

6. Secure all loose wires after installing the unit.

7. Please carefully read the operating and installation

instructions of the respective equipment before con-

necting it to this unit.

Caution

¡Please follow the laws and regulations of your

state, province or country for installation of the

unit.

Caution

¡Various settings that have been stored in the

memory in other on-board equipment (car naviga-

tion etc.) may be lost if the battery terminals are

disconnected.

Therefore, we recommend you to make a record

of or to back up the settings before disconnecting

the terminals.

After completing installation of the main unit, set

up the equipment again according to the settings.

0 – 30°

CQ-VD7003U

English

❏ Transportation Bracket Removal

Be sure to remove the transportation brackets before use (installation).

Use round head screws (

5 mmø x 6 mm) for installation. (a page 12)

Be careful not to lose these screws.

Round Head Screw

mmø x 6 mm)

Round Head Screw

mmø x 6 mm)

Transportation

Bracket

Transportation

Bracket

CQ-VD7003U

English

Installation Guide (continued)

❏ Installation Procedures (When using Mounting Collar w)

Mounting the Display Unit

Insert the Mounting Collar w into the dashboard, and

bend the mounting tabs out with a screwdriver.

Establish the rear connection of the unit.

After fixing Power Connector

!3, fix the rear of the unit to

the car body by either method (a) or (b) shown at right.

Insert Trim Plate q.

After installation

reconnect the negative

(–) battery terminal.

Attach the Mounting Springs e to the unit.

Power Connector

r Mounting Bolt

(5 mmø)

e Mounting Spring

o Flat-Head Screw

(5 mmø x 6 mm)

Note:

¡The car model, installation condi-

tions and combination of the units

used may impose some restric-

tions on opening and closing the

monitor as well as on the angle

and position to which the monitor

can be adjusted.

Fastening the Mounting Collar

How much to bend the tabs will vary depending on the

car. Bend them with a screwdriver to fasten the

Mounting Collar

securely in the dashboard.

w Mounting Collar

Dashboard

Tab

Insert the unit into Mounting Collar w.

Secure the clamp plate of Mounting Collar

w to the hook of Mounting Spring e.

Clamp plate

IMPORTANT

When this unit is installed in dash-

board, ensure that there is sufficient

air flow around the unit to prevent

damage from overheating. Do not

block any ventilation holes on the

unit.

CQ-VD7003U

English

Two holes of the mounting spring allow you to select between two mounting types as shown below.

A few millimeters of

console projecting

Less projecting

Method for Fixing the Rear of the Unit

Method for Fixing the Mounting Spring

(A) Regular installation method (B) Deeper installation method

o Flat-Head Screw

(a) Using the Rear Support Strap u.

(b) Using the Rubber Cushion (option)

Fire wall of car

3 mmø

Tapping Screw

(5 mmø x 16 mm)

Rear Support Strap

Mounting Bolt

(5 mmø)

Mounting Bolt

(5 mmø)

Rear Support Bracket

(Provided on the Car)

Rubber Bushing

(option)

Hex. Nut

(5 mmø)

Caution

¡Method (B) is not available in some types of cars.

CQ-VD7003U

English

Installation Guide (continued)

!1 Spacer

!2 Double-Faced Adhesive Tape

i Round Head Screw

(5 mmø x 6 mm)

Bracket

Mounting Hole

of a Bracket

(in section)

Existing Bracket (L) (Bracket originally attached to the car)

!2 Double-Faced

Adhesive Tape

Existing Bracket (R)

i Round Head Screw

(5 mmø x 6 mm)

!1 Spacer

❏ Installation Procedures (When not using Mounting Collar w)

Use the brackets supplied with your car when mounting this unit. The bracket shape and mounting method vary with car

manufacturers, car types and manufacturing year. Please consult your nearest dealer or installer.

Select mounting screws according to the hole positions and hole shape of the bracket.

o Flat-Head Screw (5 mmø x 6 mm) 4 pieces

!0 Round Head Screw (4 mmø x 3 mm)

4 pieces

i Round Head Screw (5 mmø x 6 mm) 2 pieces

Recycle the Round Head Screws that fixed the transportation brackets for two more

positions.

When using these

mounting holes

q Push the right and left clamp plates outward, one at a time, and pull the unit toward yourself.

w After removing the right and left clamp plates, pull the unit with both hands till it comes out.

Push here to

remove the

clamp plates.

To Remove the Unit

Use the supplied Spacer !1 if mounting hole of your

car is shaped like below.

CQ-VD7003U

English

—

SIDE BRAKE

The side brake (parking brake) switch position varies with car model.

For details on the exact location of the side brake (parking brake) switch

in your car, contact your dealer.

Attach a Clip Connector !4 to the end of the side

brake (parking brake) connection lead.

w The Clip Connector !4 is connected to the power

source side lead of the side brake (parking brake)

lever.

Connecting the Side Brake (Parking Brake) Connection Lead

Hand brake Foot brake

Side Brake (Parking Brake) Connection

Lead (Bright green)

When the side brake (parking brake) lever is

engaged, the unit is grounded by the chassis.

Side brake (parking brake) switch

Car chassis

Battery

Brake light

!4 Clip Connector

Side Brake (Parking Brake) Connection Lead

(Bright green)

Comes up to this point.

Power source side lead

Caution

¡For safety, be sure to ask your nearest professional installer to do this connection.

CQ-VD7003U

English

Electrical Connections

BATTERY 15 A

SIDE BRAKE

NAVI MUTE

ANT-CONT MAX 0.1A

FRONT SP

REAR SP

AMP-CONT MAX 0.1A

ACC

Motor Antenna Relay Control Lead (Blue)

(To motor antenna) (Max. 100 mA)

This lead is not intended for use with a switch actuated

power antenna.

Front Right + (Gray)

Front Right – (Gray/black stripe)

Front Left + (White)

Front Left – (White/black stripe)

Rear Right + (Violet)

Rear Right – (Violet/black stripe)

Rear Left + (Green)

Rear Left – (Green/black stripe)

External Amplifier Control Power Lead (Blue/white stripe)

To an external amplifier.

Battery Lead (Yellow)

To the car battery, continuous +12 V DC.

Power Lead (Red)

To ACC power, +12 V DC.

Ground Lead (Black)

To a clean, bare metallic part of the car chassis

Speaker connections

• Do not connect more than one speaker to one set of

speaker leads (except for connecting to a tweeter).

• Do not use a 3-wire type speaker system having a com-

mon earth lead.

Navi Mute Lead (Orange)

Connect to the Navi Mute Lead of the Panasonic car

navigation system. (available in future)

Side Brake (Parking Brake) Connection Lead (Bright

green)

Be sure to wire the side brake (parking brake) for safety and

preventing accidents. (a page 13)

(Noise Filter)

(Fuse 15 A)

(Resistor 1 k

Ω)

Caution

¡This unit is designed for use in a car having a 12 V negative ground battery system.

¡Be sure to insulate any exposed wires from the car chassis. Bundle all cables and keep cable terminals free from

any metal parts.

¡Note that if your car has a driving computer or a navigation computer, disconnecting the cable from the battery

may clear the memory.

¡Run the cords avoiding the spots where the temperature can be extremely high.

Power Connector

CQ-VD7003U

English

AV-OUT

PRE-OUT REAR

S.W-OUT

PRE-OUT CENTER

REVERSE

PRE-OUT FRONT

CAMERA-IN

AV1-IN

AV2-IN

REMOTE-IN

Reverse Lead

When connecting the rear view camera, use

the reverse lead. (a page 21)

Note:

Use a Reverse Extension Cord

if needed.

Note:

¡To prevent from damage to the unit, be sure to follow the wiring diagrams below.

¡Be sure to fully plug in the connectors. Secure them with clamps and tapes.

¡All other installation methods require the use of dedicated metal fittings. Consult with a qualified servicing engineer or

your dealer if other methods are required.

Video Output Terminal (AV-OUT)

Connect the rear monitor. (

a page 23)

Radio Antenna Connector (RADIO ANT IN)

RGB Connector

To the Panasonic Car Navigation System (available in future).

System-up Connector

To external devices equipped with system-up connector.

Pre-Out Connector (front)

To external amplifier.

Pre-Out Connector (center)

To external amplifier.

Pre-Out Connector (rear)

To external amplifier.

Pre-Out Subwoofer connector (mono)

To external amplifier.

Video Input Terminal (AV1-IN/AV2-IN)

Connect a VCR, camcorder, other brand’s car

navigation system, etc. (a page 22)

Note: When an external device is connected

to the system-up connector, the audio termi-

nals, {(R)(Red), (L)(White)}, of AV2-IN are

disabled.

Remote-In Lead

(not used)

Camera Input Terminal (CAMERA-IN)

Connect a rear view camera. (

a page 21)

(R)(Red)

(L)(White)

(R)(Red)

(L)(White)

(R)(Red)

(L)(White)

(Yellow)

(R)(Red)

(L)(White)

(Yellow)

(R)(Red)

(L)(White)

(Yellow)

(Brown/black stripe)

(Violet/white stripe)

(Black)

CQ-VD7003U

(Rear)

: This book refers to connections to the Panasonic car navigation system that will come onto the market in the

future. Descriptions regarding the car navigation system are boxed with a dotted line.

CQ-VD7003U

English

Electrical Connections (continued)

CHANGER IN

BATTERY 5 A

ACC

AV2-IN

Connection with DVD Changer (CX-DH801U)

CQ-VD7003U

(Rear)

RCA Cord

(Video)

(Yellow)

(Video)

(Yellow)

(L) (White)

(R) (Red)

DIN Connector

DIN Cord (Black)

DVD Changer

CX-DH801U (option)

Battery Lead

(Yellow) To the car battery, continuous +12 V DC

Power Lead (Red) (not used)

(not used)

Ground Lead (Black)

To a clean, bare metallic part of the car chassis

Note:

¡Refer to the operating instructions for the connected devices, in addition.

Power Connector

(Supplied with CX-DH801U)

Conversion Cable for DVD/CD Changer

(CA-CC30U, option)

System-up

connector

CHANGER IN

CQ-VD7003U

English

(L) (White)

(R) (Red)

DIN Connector

Conversion Cable for DVD/CD

Changer (CA-CC30U, option)

Connection with CD Changer (CX-DP880)

CQ-VD7003U

(Rear)

System-up

connector

DIN Cord (Black)

CD Changer

CX-DP880 (option)

Power Connector

(Supplied with CX-DP880)

RCA Cord

Battery Lead (Yellow)

To the car battery, continuous

+12 V DC

Ground Lead (Black)

To a clean, bare metallic part of the car

chassis

Note:

¡Refer to the operating instructions for the connected devices, in addition.

CQ-VD7003U

English

Electrical Connections (continued)

Connection with TV Tuner (CY-TUN153U)

Note:

¡Refer to the operating instructions for the connected devices, in addition.

AV2-IN

PWR-CONTAMP-CONT MAX 0.1 A

TV Tuner

CY-TUN153U (option)

CQ-VD7003U

(Rear)

(Video)

(Yellow)

(Video)

(Yellow)

RCA Cord

(supplied with CY-TUN153U)

System-up Connector

(supplied with CY-TUN153U)

(not used)

Power

Connector

Power Connector

(supplied with CY-TUN153U)

External Amplifier

Control Power Lead

Power Control Lead

CQ-VD7003U

English

FUSE

XM Satellite Radio

XMD1000* (option)

Connection with XM Satellite Radio (XMD1000)

CQ-VD7003U

(Rear)

DIN Connector

(L) (White)

(R) (Red)

* Please understand that Panasonic is not liable for modification of specifications, shape, name, and the like of the

optional XM receiver and digital adapter without prior notice because they are not manufactured by Panasonic.

Note:

¡Refer to the operating instructions for the connected devices, in addition.

System-up Connector

CHANGER IN

VIDEO-CNT

AV2-IN

CQ-VD7003U

English

Electrical Connections (continued)

Connection with Expansion Module (CY-EM100U)

CQ-VD7003U

(Rear)

Note:

¡Refer to the operating instructions for the connected devices, in addition.

VIDEO OUT

AUDIO OUT

VIDEO OUT

DVD Changer

CX-DH801U (option)

Expansion Module

CY-EM100U (option)

Conversion Cable

for DVD/CD

Changer (CA-

CC30U, option)

Direct Cable for iPod

(CA-DC300U, option)

(Video) (Yellow)

(Video)

(Yellow)

(Video)

(Yellow)

(L) (White)

RCA cord

(option)

(R) (Red)

(Video) (Yellow)

(L) (White)

(R)

(Red)

Head unit/Expansion Module

Connecting cable

(Supplied with CY-EM100U)

Camcorder

(option)

iPod

System-up

Connector

CQ-VD7003U

English

Connection with Rear View Camera

REVERSE

CAMERA-IN

Connecting the Reverse Lead

If using an optional rear view camera, the reverse lead

must be connected.

Connect the reverse lead (violet/white stripe) to the posi-

tive (+) lead of the reverse lamp (the lamp with a clear

lens that lights when the transmission gear is shifted into

the reverse position).

Note:

¡Connect the reverse lead after cutting the terminal at

the end.

¡Use a Reverse Extension Cord

!5 if needed.

Rear View Camera (option)

(Video)

(Yellow)

RCA Cord (option)

Rear View Camera

Control Unit (option)

CQ-VD7003U

(Rear)

(Video)

(Yellow)

Reverse lamp

Clip connector

(option)

Battery

Car chassis

Transmission gear

Reverse Extension Cord

(Violet/white stripe)

Reverse Lead

(Violet/white stripe)

Camera Input

Camera Input Terminal

(Yellow)

Check the reverse lamp.

Take it out of the back of

the tail lamp mount.

Note:

¡Refer to the operating instructions for the connected devices, in addition.

Page is loading ...

Panasonic CQ-VD7003U Installation guide

Panasonic CQ-VD7003U Installation guide

Panasonic CQ-VD7003U Installation guide

Related papers

Other documents