BLOTZ B10-CS-007 Assembly Instructions

Brand: BLOTZ

Model: B10-CS-007

Type: Assembly Instructions

This manual is also suitable for

B10_CS_007

10mm 5x5 ‘L-Shape’ Hospital Foyer

B10-CS-204

Please read these instructions fully before starting construction.

PVA or equivalent glue will be required to stick sections together.

Sand paper can be used to gently clean any joints.

A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due

care and remember to cut away from yourself at all times.

During the construction of this model, you may find it convenient to use pegs / elastic bands to hold

pieces in place while you allow glue to dry.

Foyer (B10-CS-204)

Start by removing the wall sections and internal

frame shown above from the sprue. Note the

walls sections are labelled ‘A’ to ‘F’ and run

clockwise starting from the long wall on the left

of the picture.

Glue walls ‘A’ to ‘D’ into place using the lugs provided.

Attach the foyer cover and bracer to wall section

‘E’ as shown.

Push the lugs of wall ‘E’ into those of ‘D’, along with

the lugs from the foyer roof and bracer – then push

wall ‘E’ so that it connects to the framework. Glue the

door section into place. Finally attach end wall ‘F’.

Apply some glue to the back of the wall covering

for ‘D’ and slide it over the foyer roof section (at

a slight angle to wall ‘D’. When it is in place, push

it flush to wall ‘D’.

Repeat the process for the wall covering for wall ‘E’,

then move round the building, gluing the coverings

into place.

Showing the coving for wall ‘A’.

10mm 5x5 ‘L-Shape’ Hospital Middle

B10-CS-256

Please read these instructions fully before starting construction.

PVA or equivalent glue will be required to stick sections together.

Sand paper can be used to gently clean any joints.

A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due

care and remember to cut away from yourself at all times.

During the construction of this model, you may find it convenient to use pegs / elastic bands to hold

pieces in place while you allow glue to dry.

Mid-Section (B10-CS-256)

Remove walls ‘A’ to ‘F’ from the sprue, along with

the framework. Starting with wall ‘A’ glue them

to the framework, working clockwise around the

model. Leave to dry.

Attach the wall coverings to walls ‘D’, then ‘E’ before

attaching the rest of the wall coverings.

Remove the six rectangular supports from the

sprue and glue one to the back of each wall

section (at the base of the wall) as shown above.

The finished middle section.

10mm 5x5 ‘L-Shape’ Hospital Roof

B10-CS-305

Please read these instructions fully before starting construction.

PVA or equivalent glue will be required to stick sections together.

Sand paper can be used to gently clean any joints.

A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due

care and remember to cut away from yourself at all times.

During the construction of this model, you may find it convenient to use pegs / elastic bands to hold

pieces in place while you allow glue to dry.

Roof Section (B10-CS-305)

Remove the roof piece and wall sections from the

sprue.

Starting with wall piece ‘A’ run clockwise around the

building adding side ‘B’, end ‘C’, side ‘D’, side ‘E’ and

finally end ‘F’.

Now apply the wall covering to walls ‘D’ then ‘E’

as shown above. Glue the other wall coverings

into place. Remove the sections of the lift from the sprue.

Glue together as shown above.

Then glue into place on the roof.

Finally, glue a rectangular support to the back of

each wall section at the base (see above).

The finished roof section.

BLOTZ B10-CS-007 Assembly Instructions

Brand: BLOTZ

Model: B10-CS-007

Type: Assembly Instructions

This manual is also suitable for

B10_CS_007

Download PDF

report

BLOTZ B10-CS-007 Assembly Instructions

This manual is also suitable for

BLOTZ B10-CS-007 Assembly Instructions

Related papers