Sharkoon MS140 Specification

Sharkoon
Brand
Sharkoon
Model
MS140
Category
Computer cases
Type
Specification
Manual
MS140
MS140
Content
1. Features 3
2. Package content 4
3. The case at a glance 5
4. Installation notes 7
5. Removing the left HDD mounting plate 8
6. Installation of a mainboard 9
7. Installation of a PSU 11
8. Installation of a HDD 12
8.1 Into the lateral HDD mountings 12
8.2 Into the bottom panel 13
9. Installation of an optical device 14
10. Installation of a 3.5" device 16
11. Installation of an add-on card 17
12. Installation of additional fans / optimized airflow 18
Dear customer!
Congratulations for purchasing this premium quality SHARKOON product.
For a long life time and to take full advantage of this product we recommend you to read this manual completely.
Enjoy our product!
SHARKOON Technologies
2
MS140
1. Features
• MicroATXcase
• 1x5.25"drivebay(external)
• 1x3.5"drivebay(external)
• Internalmountingareafor4x3.5“or6x2.5“HDDs
• 4slotsforadd-oncards
• FrontI/Owith1xUSB3.0,3xUSB2.0and2xaudio
• 1x140mmLEDfanpre-installed
• SupportsVGAcardsupto36cmlength
• Dimensions:420x175x368mm(LxWxH)
• Weight:~4kg
• Fanconguration:
Casefront 1x140mmLEDfan
Rearpanel 1x80mmor1x92mmfan(optional)
Casebottom 1x120mmfan(optional)
3
MS140
2. Package contents
• ATXcase„MS140“
• Screwkit:
Screwsformainboardand
drivemounting(3.5"and
5.25")
Mountingscrewsfor2.5"
HDDs/SSDs
ScrewsforPSUmounting ScrewsforHDDmounting
• Accessorykit:
Stand-offsformainboard Washers Cabletie(A)andspeaker(B)


Note:
If you are missing any of the items listed above, please contact our customer service immediately:
[email protected] (Germany and Europe)
[email protected] (international).
4
A
B
MS140
3. The case at a glance
Frontpanel
A – 5.25"drivebay
B – PowerLED
C – On/offbutton
D – FrontI/O:
a – 1xUSB3.0
b – 3xUSB2.0and
c – 2xaudio
E – 3.5"mountingbay
F – LEDforHDDactivity
G– Resetbutton
H – behindthemeshpanel:1x140mmLEDfan
Sidepanel(closed/left)
A–Airinlet
a
b b
c
A
A
B
B
C
D
E
E
F
G
H
5
A
MS140
Sidepanel(opened/left)
A – 5.25"drivebay
B – 3.5"mountingbay
C – Attachmentsfor4x3.5"or
6x2.5"-HDDs/SSDs
D – Mainboardmountingpanel
Rearpanel
A – PSUbracket
B – OpeningforI/Oshield
C – Fanbracket(80or92mm)
D – Slotbezels
E – Thumbscrews
F – ConnectioncableforthefrontUSB3.0plug
6
A
A
B
B
C
D
C
D
E
E
E
E
F
MS140
Bottompanel
A – Casefeet
B – Attachmentfor3.5“HDD
C – AttachmentscrewsforHDDmountingpanel
D – Bracketfor120mmfan
4. Installation notes
1.ForfurtherinformationonhowtoinstallthePCcomponents,alsorefertotheirrespectiveinstructions.
2.InordertoinstalllongVGAcards,itmightbenecessarytoremovetheleftHDDmountingpanel(see5.).
Tohavetheoptiontoinstallatleasttwo3.5“HDDs,thereisanadditionalHDDattachmentinthebottom
panelofthecase.
7
A A
AA
B B
BB
C C
D
MS140
Fig.1
1.Unscrewthethumbscrewsonthebacksideofthecaseandremovebothsidepanels.
2.UnscrewthethreeattachmentscrewsoftheHDDmountingpanelandremovethepanelfromthecase
(g.2a-c).
 
Fig.2a-c
5. Removing the HDD mounting plate
InordertoinstalllongVGAcards,andtoutilizethebottomHDDattachment,theleftHDDmountingpanel
(g.1)mustberemovedasfollows:
8
MS140
6. Installation of a mainboard
1.Unscrewthethumbscrewsonthebacksideofthecaseandremovetheleftsidepanel.Laydownthe
casesidewiseonanevensurface.
2.Themountingpanelofthemainboardinsidethecaseprovidesvariousmountingholestoxthe
standoffs(g.3).
Fig.3
Themainboardcontainsspecialscrewmounts(g.4).
Fig.4
Placethemainboardtothemountingpanel.Astandoffmustbescrewedintoeveryholeonthe
mountingpanelvisiblethroughthemainboard’sscrewopenings.
9
MS140
3.Removethemainboardandscrewthestandoffsintotherespectiveholesofthemountingpanel(g.5).
(Standoffs)
Fig.5
4.InserttheI/Oshield(deliveredwiththemainboard)intotheI/Oshieldopeningintherearpanelofthe
case.
5.Placethemainboardbackontothestandoffsandscrewthemainboardtothem(g.6).
(Screwsformainboardmounting)
Fig.6
10
MS140
6.Plugtheconnectorsofthecase’sfrontbezeltotherespectiveconnectorsofthemainboard(alsoreferto
yourmainboard’smanualforfurtherinformation).
7. Installation of a PSU
1.PositionthecaseinfrontofyouandsetthePSUfromtheinsideagainstthePSUbracketonthecase’s
rearpanel.
2.ScrewthePSUtothecasefromtheoutside(g.7).
(ScrewsforPSUmounting)
Fig.7
11
MS140
8. Installation of a HDD
8.1 Into the lateral HDD mountings
A – Attachmentsfor3.5"HDDs(decoupledmounting)
B – Attachmentsfor2.5"HDDs/SSDs
Note:
Prior to the 2.5"HDD/SSD installation, the buffers for 3.5" HDDs must be removed from the attachments.
1.HoldtheHDD/SSDagainsttherespectiveattachment(g.8aandb).

Fig.8a(3.5"HDD) Fig.8b(2.5"HDD)
12
A B
MS140
2.AttachtheHDD/SSDtothecasefromtheoutside(g.9aandb).

(Screwsfordrive/HDDmounting)
Fig.9a(3.5"HDD) Fig.9b(2.5"HDD)
3.ConnecttheHDDtothepowersupplyandthemainboard.
8.2 Into the bottom panel
1.TousetheHDDattachmentinthebottompanel,theleftHDDattachmentpanelmustberemovedfrom
thecase(seeabove5.).
2.RemovefourbuffersfromtheHDDattachmentpanel,whichyouremovedfromthecase,andinsert
themintotheopeningsonthecase‘sbottompanel(g.10).
(Buffers)
Fig.10
13
MS140
3.PlacetheHDDontothebuffersandattachittothecasefromtheoutside(g.11aandb).

Fig.11aundb
4.ConnecttheHDDtothepowersupplyandthemainboard.
9. Installation of an optical device
1.Removethecase’sfrontpanelbygentlypullingittowardsyou(g.12).
Fig.12
14
MS140
2.Dismantlethe5.25"frontbezelfromthemountingbaybypushingitoutofthefrontpanel(g.13).
Fig.13
3.Placethefrontpanelbackontothecase.
4.Slidetheopticaldriveintothecase’sdrivebay(g.14).
Fig.14
15
MS140
5.Attachtheopticaldevicetothecasefrombothsides(g.15).
(Screwsfordrivemounting)
Fig.15
6.Connecttheopticaldrivetothepowersupplyandthemainboard.
10. Installation of a 3.5" device
1.Removethecase’sfrontpanelbygentlypullingittowardsyou.
2.Dismantlethe3.5"frontbezelbypushingitoutofthefrontpanel(g.16).
Fig.16
3.Placethefrontpanelbackontothecase.
16
MS140
4.Slidethe3.5"deviceintothe3.5"mountingbayandattachitfrombothsides(g.17).
(Screwsfor5.25"drivemounting)
Fig.17
5.Connectthe3.5"devicetothepowersupplyandthemainboard.
11. Installation of an add-on card
1.Removetheanchorscrewoftheslotbezelandtakeitfromthecase(g.18).
Fig.18
17
MS140
2.Inserttheadd-oncardintotherespectiveslotofthemainboardandattachittothecaseusingthe
anchorscrew(g.19).
Fig.19
12. Installation of additional fans / optimized airflow
1.Placethefanagainsttherespectivebracketfromtheinsideofthecase.
2.Screwthefantotheattachmentfromtheoutside.
Notes:
1. When installing fans, make sure that (cool) air is taken in on the front/bottom of the case and blown
out on its rear side/top. The PC components with the highest heat development should be placed directly
within the airflow.
2. The installation of the lower fan is an additional application for VGA cooling.
The bottom PCI slot of the mainboard will be occupied when used.
18
MS140
Legal disclaimer:
AsacontinuingpolicyofproductimprovementatSHARKOON,thedesignandspecicationsaresubjectto
changewithoutpriornotice.Nationalproductspecicationsmayvary.
Allrightsreservedespecially(alsoinextracts)fortranslation,reprinting,reproductionbycopyingorother
technicalmeans.Infringementswillleadtocompensation.
Allrightsreservedespeciallyincaseofassignationofpatentorutilitypatent.Meansofdeliveryandtechnical
modicationsreserved.
Disposalofyouroldproduct
Yourproductisdesignedandmanufacturedwithhighqualitymaterialsandcomponents,whichcanberecyc-
ledandreused.
Whenthiscrossed-outwheeledbinsymbolisattachedtoaproduct,itmeanstheproductiscoveredbythe
EuropeanDirective2002/96/EC.
Pleasebeinformedaboutthelocalseparatecollectionsystemforelectricalandelectronicproducts.
Pleaseactaccordingtoyourlocalrulesanddonotdisposeofyouroldproductswithyournormalhousehold
waste.Thecorrectdisposalofyouroldproductwillhelppreventpotentialnegativeconsequencestotheenvi-
ronmentandhumanhealth.
© SHARKOON Technologies 2011
www.sharkoon.com
19
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19

Sharkoon MS140 Specification

Sharkoon
Brand
Sharkoon
Model
MS140
Category
Computer cases
Type
Specification
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents