Commercial Electric MB-64649 User manual

Brand: Commercial Electric

Model: MB-64649

Category: Flat panel wall mounts

Type: User manual

The Commercial Electric MB-64649 Extend + Tilting TV Wall Mount is designed to securely hold TVs ranging from 42 to 90 inches with a maximum weight capacity of 154 lbs. It features a tilting mechanism that allows you to adjust the viewing angle of your TV for optimal comfort, and a swivel function that enables you to easily position your TV for the best viewing experience from different angles. The mount is constructed from durable steel and comes with all the necessary hardware for easy installation on wood studs or concrete walls.

(For 42" - 90" TVs

Fits VESA 200/300/400/500/600)

Extend + Tilting TV Wall Mount

MB-64649

XXXXXXXX

Before you begin, carefully read and understand the instructions

in this manual. Please follow the instructions in the order

presented in this manual and observe all warnings and cautions.

4-11

3/16 in. (4.5 mm)

wood drill bit or

3/8 in. (10 mm)

masonry drill bit.

This mount has been tested to

support a television with diagonal

screen sizes between 42 in. and 90 in.

(106.7 cm & 2.29 m) and a weight

up to 154 lbs. (70 kgs).

25.7"(654mm)

8.1"(207mm)

min5.9"~max27.1"

(min150~max690mm)

min3"~max5.2"

(min78~max134mm)

16.9"(430mm)

min1.96"~max15.9"

(min50~max405mm)

structural strength for this product can

result in physical injury and/or damage to

equipment. It is the installer's responsibility

to make sure the structure to which this

product is attached can support four

times the combined weight of all equipment.

Reinforce the structure as required before

installing the product.

for use only with the maximum weights

indicated. Use with products heavier than the

maximum weights indicated may result in

collapse of the mount and its accessories

causing possible injury. This mount has been

tested to support 154 lbs. (70 kgs). Use with

products heavier than the rated weights

indicated may result in instability causing

possible injury.

This wall mount is intended

Part Description Quantity

AA 6

BB 6

CC 6

DD 4 each

8 each

Nylon anchor

Lag bolt washer

Lag bolt

Screw (size M5x14, M6x14, M6x30, M8x30, M8x50)

Washer

Spacer (size Φ15xΦ8x5 and Φ15xΦ8x15)

Pre-Installation

10 20 30 40 50 60 70 80 90 100mm

1 2 3 4in

Part Description Quantity

A Mounting plate 1

B Mounting bracket 1

C Mounting bracket 1

DBubble level 1

EAllen key 1

brick

Screw is too

long

Screw ts

correctly

Screw is too

short

DD EE

1 2

injuries and property damage, make sure that

there are adequate threads to secure the

brackets to your TV. If you encounter resistance,

stop immediately and contact customer service.

Use the shortest screw and spacer combination

to accommodate your TV. Using hardware that is

too long may damage your TV. However, using

a screw that is too short may cause your TV to

fall from the mount.

To avoid potential personal

CAUTION:

Installation

Mounting brackets to the TV

Use the washers (EE) and screws (DD, size M5x14, M6x14) to attach the TV if it has a ﬂat back.

Or use the spacers (FF), washers (EE) and screws (DD, size M6x30, M8x30, M8x50) to

attach the TV if it has a curved or recessed back.

CAUTION: Tighten the screws so the brackets

are ﬁrmly attached. DO NOT OVERTIGHTEN. This

may damage your TV.

Installation (continued)

B C

DD EE

B C

DD EE FF

brick

Ensure the wall you select is a weight-bearing wall.

Failure to observe this precaution can result in serious physical

injury and/or property damage. Consult a professional installer or

contact customer service if you have any questions.

CAUTION:

Installation (continued)

After you have mounted the brackets to the TV,

determine the mounting location on the wall.

Select the best location that you want the PICTURE AREA

to be positioned. A good rule of thumb is to have the

primary viewer’s eye level to be about 1/3 of the

distance from the bottom of the picture area.

Eye Level

42-48"

(106-122 cm)

Typical Height from Floor

2/3

1/3

Installing the wall mount (concrete/brick wall)

Use the Mounting plate (A) as a template to mark the installation holes. Use the bubble level (D) to ensure the

mounting plate (A) is level.

Insert anchors (AA) into the holes. Ensure the anchors are completely flush to the concrete surface even if covered

by a layer of joint compound or other material.

Attach the mounting plate (A) to the wall using the lag bolts (CC) and lag bolt washers (BB) as shown.

Installation (continued)

bricks

brick.

Use a 1/4 in. (6 mm) masonry drill bit to slowly drill 2.4 in. (60 mm) pilot holes. Then use a 3/8 in. (10 mm) masonry

drill bit to expand pilot holes.

BB CC

CAUTION:

Avoid potential personal injury or

property damage! Drywall covering the wall must not

exceed 5/8 in.(16mm)

Use a commercially-available stud finder to locate the stud centers in the wall. Studs are usually spaced 16 in. apart.

Use the mounting plate (A) as a template to mark the installation holes. Use the bubble level (D) to ensure the mounting

plate (A) is level.

Attach the mounting plate (A) to the wall using the lag bolts (CC) and lag bolt washers (BB) as shown.

Use a 3/16 in. (4.5mm) drill bit to slowly drill 2.2 in. (55 mm) pilot holes.

Installing the wall mount (wood stud)

Installation (continued)

HEAVY! You will need

assistance with this step.

Mounting the TV to the mounting plate

Pulling the ropes to open the stopper in the lower notch of the mounting brackets (B&C), push the TV as

shown to align the mounting brackets (B&C) with the mounting plate (A) then release the rope to secure

the TV.

Holding the TV with the top of the screen tilted toward the wall, slide the upper notches of the mounting

brackets (B&C) over the upper lip of the mounting plate (A).

Using padlocks

Apply 2 padlocks with a shackle that is long enough to cross the the locking holes on the lower side of

the mounting brackets (B&C) to prevent stealing or other unwanted removal.

Installation (continued)

Leveling and adjustments

Put the bubble level (D) on the top of the TV and use the Allen Key (E) to adjust the screws on the

mounting brackets (B&C) as shown to ﬁne-tune to the TV.

To tilt the TV, release the adjustment knob as shown to tilt up/back the TV.

To pivot the TV, hold one side of the TV and pull the other side out.

Installation (continued)

Commercial Electric MB-64649 User manual

Brand: Commercial Electric

Model: MB-64649

Category: Flat panel wall mounts

Type: User manual

Download PDF

report

Commercial Electric MB-64649 User manual

Commercial Electric MB-64649 User manual

Related papers

Other documents