2. AcuityBrands
  3. 912-00232-000 BH
912-00232-000 BH

AcuityBrands 912-00232-000 BH User manual

  • Hello! I'm your chat assistant. I've reviewed the provided installation instructions for the Acuity Brands BHL luminaire. This document covers various installation methods including grid ceiling, mud-in hard ceiling, and flanged hard ceiling, including wiring and safety procedures. Feel free to ask me any questions about the installation process or any other aspect mentioned in the instructions.
  • What type of gloves should be used when handling the luminaire?
    What should I do if the lens surface becomes smudged?
    What is the proper torque for reinstalling fasteners after mudding?
, Luminaire LED.
Pre-Launch
BHL Luminaire
INSTALLATION INSTRUCTIONS
A. General Identification of BHL Luminaire……………......................................................................................................................Page 2
B. Grid Ceiling Install (FG,TG)……....................................................................................................................................................Page 3
C. Mud in Hard Ceiling Install (GB)………………………........................................................................................................................Page 5
D. Flanged Hard Ceiling Install (FL)……………………………….............................................................................................................. Page 7
E. Control Wiring………….……………..................................................................................................................................................Page 11
12/2021 ECO# 040-254560
BHL INSTALL INSTRUCTIONS 2
A. General Identification of BHL Luminaire
IMPORTANT: Wearcottongloves AND lift and handle theluminaire from theends to avoid damaging or soiling thelens
surface. Should the lens surface become smudged or otherwise blemished, cleanusing only a soft, microfiber cottoncloth.
ROOM FACING TAMPER
RESISTANT FASTENER
(TR15 FASTENER)
912-00232-000 REV. A
1400 Lester Rd NW, Conyers, GA 30012 • Tel: 800.705.SERV(7378) • Email: •Website: https://luminaireled.acuitybrands.com/
© 2021 Acuity Brands Lighting, Inc. All Rights Reserved. “LuminaireLED”is a registered trademark of Acuity Brands Lighting. Products in
this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice. Limited warranty applies.
Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
ELECTRICAL ACCESS PLATE
CEILING TRIM (WILL VARY
BASED ON APPLICATION)
ELECTRICAL ENCLOSURE
GASKET
INSULATION DETECTORS
(IF APPLICABLE)
Pre-Launch
B. Grid Ceiling Install (FG,TG)
BHL INSTALL INSTRUCTIONS 3
12/2021
912-00232-000
1400 Lester Rd NW, Conyers, GA 30012 • Tel: 800.705.SERV(7378) • Email: •Website: https://luminaireled.acuitybrands.com/
© 2021 Acuity Brands Lighting, Inc. All Rights Reserved. “LuminaireLED”is a registered trademark of Acuity Brands Lighting. Products in
this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice. Limited warranty applies.
Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
1
Ensure grid spacing is accurate.
BHL 2’ intended for 0’-6” X 2’-0” O.C. grid
BHL 4’ intended for 0’-6” X 4’-0” O.C. grid
Tilt and push the BHL luminaire through the intended
spacing from the bottom. Angle the luminaire to clear the
insulation detectors, if applicable. The luminaire ceiling
flange should then overlap the room facing grid piece.
2
**For IP66 required applications** Sealant or gasket
must be field applied between overlap flange and grid
rail to ensure room seal. Acuity Brands is not
responsible for materials or installation that would
ensure IP66 room rating.
Illustrated above is (FG) flat tee grid install. All step
apply to (FG) and (TG). See step 6 for (TG) trim
illustration.
34a
Locate the (4) grid support and alignment brackets.
For your application select which tab height that will
work best. Bend the tab 90 degrees to hold the fixture in
place.
Pre-Launch
BHL INSTALL INSTRUCTIONS 4
12/2021
912-00232-000
1400 Lester Rd NW, Conyers, GA 30012 • Tel: 800.705.SERV(7378) • Email: •Website: https://luminaireled.acuitybrands.com/
© 2021 Acuity Brands Lighting, Inc. All Rights Reserved. “LuminaireLED”is a registered trademark of Acuity Brands Lighting. Products in
this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice. Limited warranty applies.
Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
4b
Support luminaire using hole in grid bracket and tie
luminaire to structure. Luminaire must be supported by
more than grid rails
Locate and remove access plate to wire fixture. See
control wiring section for application specific instructions.
5
6
Example of (TG) tegular tile install. All pervious steps
are applicable to TG installation as well.
Pre-Launch
C. Mud in Hard Ceiling Install (GB)
BHL INSTALL INSTRUCTIONS 5
12/2021
912-00232-000
1400 Lester Rd NW, Conyers, GA 30012 • Tel: 800.705.SERV(7378) • Email: •Website: https://luminaireled.acuitybrands.com/
© 2021 Acuity Brands Lighting, Inc. All Rights Reserved. “LuminaireLED”is a registered trademark of Acuity Brands Lighting. Products in
this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice. Limited warranty applies.
Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
1
Check rough cut size and blocking is in place.
Blocking should be spaced 5-1/2” inches apart in all
applications
BHL 2’ rough cut should be 0’-’5 ¼” X 1’-23 ¼”
BHL 4’ rough cut should be 0’-’5 ¼” X 3’-23 ¼”
Locate and remove access plate to wire fixture. **For
the GB application the fixture must be wired before
installation** See control wiring section for application
specific instructions.
2
Push luminaire into ceiling rough cut. Center the
luminaire within the hole. Fasten the luminaire to the ceiling using provided
countersunk holes. Must fasten to blocking/structure
behind visible ceiling. Ceiling fasteners by others,
countersunk holes sized for #8 or #10 flat head screw.
3 4
Pre-Launch
BHL INSTALL INSTRUCTIONS 6
12/2021
912-00232-000
1400 Lester Rd NW, Conyers, GA 30012 • Tel: 800.705.SERV(7378) • Email: •Website: https://luminaireled.acuitybrands.com/
© 2021 Acuity Brands Lighting, Inc. All Rights Reserved. “LuminaireLED”is a registered trademark of Acuity Brands Lighting. Products in
this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice. Limited warranty applies.
Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
5
Remove the ceiling trim and diffuser by removing the
#8 TR15 fasteners.
6
Store the ceiling trim, diffuser, and fasteners for
post mud installation. By removing these components,
you reduce the risk to of mudding the luminaire closed or
getting ceiling paint on the luminaire.
7
Using provided ridged trim to mud into ceiling. Avoid
getting material into empty cavity where the diffuser and
trim will be placed back in.
Reinstall the diffuser, ceiling trim and fasteners.
Fasteners should be torqued to 17 in/lbs. **Improper
/installation of door and diffuser will not allow for IP66
room seal**
8
Pre-Launch
D. Flanged Hard Ceiling Install (FL)
BHL INSTALL INSTRUCTIONS 7
1400 Lester Rd NW, Conyers, GA 30012 • Tel: 800.705.SERV(7378) • Email: •Website: https://luminaireled.acuitybrands.com/
© 2021 Acuity Brands Lighting, Inc. All Rights Reserved. “LuminaireLED”is a registered trademark of Acuity Brands Lighting. Products in
this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice. Limited warranty applies.
Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
12/2021
912-00232-000
1
Check rough cut size and blocking is in place.
BHL 2’ rough cut should be 0’-’5” X 1’-23 ¼”
BHL 4’ rough cut should be 0’-’5” X 3’-23 ¼”
**If access is available to ceiling plenum skip to step 2
through 12 and continue with step 2B**
2
Locate and identify ceiling template side rails, 2 per
luminaire template required.
1 –Template side rail
2 –Snap in teeth and alignment pieces
Notes:
-Number of snap in teeth pieces will vary based on length
-Snap in teeth with interact with spring clips on luminaire
1
2
3
Locate and identify the ceiling template end plates, 2
per luminaire ceiling template required. Assembly ceiling template, using the provided hex
washer head screw (8 screws per template). Torque
fasteners to 15in/lbs.
2
4
Alignment tab
Pre-Launch
BHL INSTALL INSTRUCTIONS 8
1400 Lester Rd NW, Conyers, GA 30012 • Tel: 800.705.SERV(7378) • Email: •Website: https://luminaireled.acuitybrands.com/
© 2021 Acuity Brands Lighting, Inc. All Rights Reserved. “LuminaireLED”is a registered trademark of Acuity Brands Lighting. Products in
this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice. Limited warranty applies.
Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
12/2021
912-00232-000
5
Final assembly of ceiling template. 2FT shown, template
will vary based on length.
6
Rotate and tilt ceiling template through the ceiling
rough cut.
78
Rotate the template in the plenum ensuring it is in the
orientation shown above. **If snap in teeth are not
orientated correctly, damage to template, ceiling, or
luminaire may occur**
Center, fasten, and secure ceiling template in place.
The blue arrows above illustrate the recommended location
of fasteners through the ceiling template bottom flange.
**Mounting means and/or fasteners provided by others.**
Top
Top
Pre-Launch
BHL INSTALL INSTRUCTIONS 9
1400 Lester Rd NW, Conyers, GA 30012 • Tel: 800.705.SERV(7378) • Email: •Website: https://luminaireled.acuitybrands.com/
© 2021 Acuity Brands Lighting, Inc. All Rights Reserved. “LuminaireLED”is a registered trademark of Acuity Brands Lighting. Products in
this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice. Limited warranty applies.
Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
12/2021
912-00232-000
910
Locate luminaire access plate and make wiring
connections. Insulation detectors may vary based on
ordered configuration. If “NLT” or “NLIGHT” is ordered
ensure to locate and plug in the RJ45 adaptor.
***IMPORTANT*** Test luminaire to ensure its
functioning properly before beginning to install within
the ceiling template.
11
**For IP required applications** Sealant or gasket must
be field applied between overlap flange and ceiling before
installed into ceiling. Acuity Brands is not responsible for
materials or installation that would ensure IP66 room
rating.
Tilt and push the luminaire into the rough cut until it
snaps into place securely. Angle the luminaire so the
insulation detector goes into the plenum first, if
applicable. The spring clips on the luminaire should
engage the previously installed ceiling template. If
engagement is not occurring, please verify step 7-10 for
template location.
12
Locate and identify the spring clips on the luminaire.
These will interact with snap in teeth on the ceiling
template.
Pre-Launch
BHL INSTALL INSTRUCTIONS 10
1400 Lester Rd NW, Conyers, GA 30012 • Tel: 800.705.SERV(7378) • Email: •Website: https://luminaireled.acuitybrands.com/
© 2021 Acuity Brands Lighting, Inc. All Rights Reserved. “LuminaireLED”is a registered trademark of Acuity Brands Lighting. Products in
this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice. Limited warranty applies.
Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
12/2021
912-00232-000
12
2B
Push the luminaire against ceiling to minimize gaps and
finish installation.
3B
**For IP required applications** Sealant or gasket must
be field applied between overlap flange and ceiling before
installed into ceiling. Acuity Brands is not responsible for
materials or installation that would ensure IP66 room
rating.
Tilt and push the luminaire into the rough cut and
support the luminaire using the support brackets
illustrated in step 2B. **Mounting means and/or
fasteners provided by others.**
4B
Locate and identify the support bracket on the
luminaire. If access to plenum is available and/or using
snap in template is not possible the luminaire can be
supported via these brackets.
5B
Locate luminaire access plate and make wiring
connections. Insulation detectors may vary based on
ordered configuration. If “NLT” or “NLIGHT” is ordered
ensure to locate and plug in the RJ45 adaptor.
Step 12 concludes non plenum access
(FL) installations, Step 2B through 5B
illustrates optional plenum access (FL)
installation
Pre-Launch
BHL INSTALL INSTRUCTIONS 11
1400 Lester Rd NW, Conyers, GA 30012 • Tel: 800.705.SERV(7378) • Email: •Website: https://luminaireled.acuitybrands.com/
© 2021 Acuity Brands Lighting, Inc. All Rights Reserved. “LuminaireLED” is a registered trademark of Acuity Brands Lighting. Products in
this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice. Limited warranty applies.
Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
12/2021
912-00232-000
U2/U4 ZT
E. Control Wiring
H
N
GRN
DIM+
DIM-
H
N
GRN
DIM+
DIM-
U2/U4 ZT RL/NL
RL/NL DIM-
RL/NL DIM+
RL/NL H
H
N
GRN
DIM+
DIM-
RL/NL DIM-
RL/NL DIM+
RL/NL H BLK/ORG
EMG H
U4 ZT EMG310T20 RL
H
N
GRN
RJ45 NLIGHT CONNECTOR
H
N
GRN
BLK/ORG
EMG H
RJ45 NLIGHT CONNECTOR
U2/U4 (MUMO) NLIGHT
U2/U4 (MUMO) NLIGHT EMG310T20
**IMPORTANT**
- Contact tech support for any additional wiring
questions @ 800.705.SERV(7378)
Pre-Launch
/